Wireless Issues

[chadders]

laptop:~# lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller IDE (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc M66-P ATI Mobility Radeon X1700
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
06:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
06:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
06:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
06:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a)
laptop:~# ipw3945d 
ipw3945d - regulatory daemon
Copyright (C) 2005-2006 Intel Corporation. All rights reserved.
version: 1.7.22
2007-07-27 20:18:45: ERROR: Could not find Intel PRO/Wireless 3945ABG Network Connection
laptop:~# ls /lib/firmware/
ipw3945.ucode
laptop:~# modprobe ipw3945
FATAL: Error inserting ipw3945 (/lib/modules/2.6.22-1-686/kernel/drivers/net/wireless/ipw3945.ko): Unknown symbol in module, or unknown parameter (see dmesg)
FATAL: Error running install command for ipw3945
laptop:~#

... needless to say, help. I can't get my wireless card working.

[chadders]

This might also help:

chadders@laptop:~$ dmesg
Linux version 2.6.22-1-686 (Debian 2.6.22-2) (waldi@debian.org) (gcc version 4.1.3 20070718 (prerelease) (Debian 4.1.2-14)) #1 SMP Mon Jul 23 13:23:02 UTC 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable)
 BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data)
 BIOS-e820: 000000003ffce000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 262080) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   262080
early_node_map[1] active PFN ranges
    0:        0 ->   262080
On node 0 totalpages: 262080
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 255 pages used for memmap
  HighMem zone: 32449 pages, LIFO batch:7
DMI 2.4 present.
ACPI: RSDP 000F7AD0, 0014 (r0 ACPIAM)
ACPI: RSDT 3FFC0000, 0040 (r1 AMI    OEMRSDT   9000627 MSFT       97)
ACPI: FACP 3FFC0200, 0084 (r2 AMI    OEMFACP   9000627 MSFT       97)
ACPI: DSDT 3FFC05E0, 8406 (r1  F3J00 F3J00001        1 INTL  2002026)
ACPI: FACS 3FFCE000, 0040
ACPI: APIC 3FFC0390, 005C (r1 AMI    OEMAPIC   9000627 MSFT       97)
ACPI: MCFG 3FFC03F0, 003C (r1 AMI    OEMMCFG   9000627 MSFT       97)
ACPI: BOOT 3FFC05B0, 0028 (r1 AMI    OEMBOOT   9000627 MSFT       97)
ACPI: SLIC 3FFC0430, 0176 (r1 AMI    OEMSLIC   9000627 MSFT       97)
ACPI: OEMB 3FFCE040, 0046 (r1 AMI    AMI_OEM   9000627 MSFT       97)
ACPI: TCPA 3FFC89F0, 0032 (r1 AMI    TBLOEMID        1 MSFT       97)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bee00000)
Built 1 zonelists.  Total pages: 260033
Kernel command line: root=/dev/sda6 ro 
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1662.538 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1029500k/1048320k available (1688k kernel code, 18112k reserved, 649k data, 244k init, 130816k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4e000 - 0xfffff000   ( 708 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc034f000 - 0xc038c000   ( 244 kB)
      .data : 0xc02a6187 - 0xc03487e4   ( 649 kB)
      .text : 0xc0100000 - 0xc02a6187   (1688 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3329.07 BogoMIPS (lpj=6658145)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e39d 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e39d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) Core(TM)2 CPU         T5500  @ 1.66GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.24 BogoMIPS (lpj=6650486)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e39d 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e39d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 CPU         T5500  @ 1.66GHz stepping 06
Total of 2 processors activated (6654.31 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=77
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=6
PCI: Using configuration type 1
Setting up standard PCI resources
APIC error on CPU1: 00(40)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 12)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: RTC can wake from S4
pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
pnp: 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
pnp: 00:08: iomem range 0xfed45000-0xfed89fff has been reserved
Time: tsc clocksource has been installed.
pnp: 00:08: iomem range 0xfed45000-0xfed89fff has been reserved
pnp: 00:09: ioport range 0x250-0x253 has been reserved
pnp: 00:09: ioport range 0x256-0x25f has been reserved
pnp: 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:09: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:09: iomem range 0xfec10000-0xfec17fff has been reserved
pnp: 00:09: iomem range 0xfec18000-0xfec1ffff has been reserved
pnp: 00:0b: iomem range 0xe0000000-0xe3ffffff has been reserved
pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0c: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0c: iomem range 0x100000-0x3fffffff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: 9000-bfff
  MEM window: fdf00000-fdffffff
  PREFETCH window: bdf00000-ddefffff
PCI: Bridge: 0000:00:1c.0
  IO window: c000-cfff
  MEM window: fe000000-fe0fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
  IO window: disabled.
  MEM window: fe100000-fe1fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
  IO window: d000-dfff
  MEM window: fe200000-fe9fffff
  PREFETCH window: ddf00000-dfefffff
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: fea00000-feafffff
  PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
Freeing initrd memory: 6096k freed
Simple Boot Flag at 0x52 set to 0x1
audit: initializing netlink socket (disabled)
audit(1185566357.008:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 244k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: SSDT 3FFC8A30, 0D07 (r1    AMI   CPU1PM        1 INTL  2002026)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Warning (tbutils-0158): Incorrect checksum in table [SSDT] -  F0, should be B1 [20070126]
ACPI: SSDT 3FFC9740, 0D07 (r1    AMI   CPU2PM        1 INTL  2002026)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU2] (supports 8 throttling states)
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
ACPI: Thermal Zone [THRM] (54 C)
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: RTL8168b/8111b at 0xf8842000, 00:18:f3:e4:7f:41, IRQ 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000ec00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000e880
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e480
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfebfbc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 16 (level, low) -> IRQ 16
firewire_ohci: Added fw-ohci device 0000:06:01.0, OHCI version 1.0
SCSI subsystem initialized
libata version 2.21 loaded.
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
ata1.00: ATA-7: Hitachi HTS541680J9SA00, SB2OC70P, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
firewire_core: created new fw device fw0 (0 config rom retries)
ata2.00: ATAPI: MATSHITADVD-RAM UJ-850S, 1.21, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54168 SB2O PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM            MATSHITA DVD-RAM UJ-850S  1.21 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
usb 5-8: new high speed USB device using ehci_hcd and address 4
usb 5-8: configuration #1 chosen from 1 choice
Attempting manual resume
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 2-1: new low speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
usb 2-2: new full speed USB device using uhci_hcd and address 4
usb 2-2: configuration #1 chosen from 1 choice
Linux agpgart interface v0.102 (c) Dave Jones
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
intel_rng: FWH not detected
Real Time Clock Driver v1.12ac
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:06:01.1 [1180:0822] (rev 19)
ACPI: PCI Interrupt 0000:06:01.1[B] -> GSI 17 (level, low) -> IRQ 17
mmc0: SDHCI at 0xfeaff400 irq 17 DMA
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 20
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 4 if 1 alt 0 proto 2 vid 0x03F0 pid 0x3111
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
ipw3945: Unknown symbol ieee80211_wx_get_encodeext
ipw3945: Unknown symbol ieee80211_wx_set_encode
ipw3945: Unknown symbol ieee80211_wx_get_encode
ipw3945: Unknown symbol ieee80211_txb_free
ipw3945: Unknown symbol ieee80211_wx_set_encodeext
ipw3945: Unknown symbol ieee80211_wx_get_scan
ipw3945: Unknown symbol escape_essid
ipw3945: Unknown symbol ieee80211_freq_to_channel
ipw3945: Unknown symbol ieee80211_set_geo
ipw3945: Unknown symbol ieee80211_rx
ipw3945: Unknown symbol ieee80211_get_channel
ipw3945: Unknown symbol ieee80211_channel_to_index
ipw3945: Unknown symbol ieee80211_rx_mgt
ipw3945: Unknown symbol ieee80211_get_geo
ipw3945: Unknown symbol free_ieee80211
ipw3945: Unknown symbol ieee80211_tx_frame
ipw3945: Unknown symbol ieee80211_is_valid_channel
ipw3945: Unknown symbol ieee80211_get_channel_flags
ipw3945: Unknown symbol alloc_ieee80211
usbcore: registered new interface driver hiddev
input: PC Speaker as /class/input/input1
input: Logitech Logitech USB Optical Mouse as /class/input/input2
input: USB HID v1.11 Mouse [Logitech Logitech USB Optical Mouse] on usb-0000:00:1d.1-1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input3
Adding 2096440k swap on /dev/sda7.  Priority:-1 extents:1 across:2096440k
EXT3 FS on sda6, internal journal
loop: module loaded
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
r8169: eth1: link up
r8169: eth1: link up
ACPI Exception (exoparg2-0442): AE_AML_PACKAGE_LIMIT, Index (0FFFFFFFD) is beyond end of object [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU1._PSS] (Node df9d3a18), AE_AML_PACKAGE_LIMIT
ACPI Exception (processor_perflib-0234): AE_AML_PACKAGE_LIMIT, Evaluating _PSS [20070126]
ACPI Exception (exoparg2-0442): AE_AML_PACKAGE_LIMIT, Index (0FFFFFFFD) is beyond end of object [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU2._PSS] (Node df9d3860), AE_AML_PACKAGE_LIMIT
ACPI Exception (processor_perflib-0234): AE_AML_PACKAGE_LIMIT, Evaluating _PSS [20070126]
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [AC0] (on-line)
input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input6
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input7
ACPI: Sleep Button (CM) [SLPB]
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
[fglrx] USWC is disabled in module parameters
[fglrx] PAT is disabled!
[fglrx] module loaded - fglrx 8.39.4 [Jul 20 2007] on minor 0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[fglrx] total      GART = 130023424
[fglrx] free       GART = 114032640
[fglrx] max single GART = 114032640
[fglrx] total      LFB  = 268304384
[fglrx] free       LFB  = 233426944
[fglrx] max single LFB  = 233426944
[fglrx] total      Inv  = 0
[fglrx] free       Inv  = 0
[fglrx] max single Inv  = 0
[fglrx] total      TIM  = 0
set_rtc_mmss: can't update from 0 to 59
eth1: no IPv6 routers present
ISO 9660 Extensions: Microsoft Joliet Level 1
ISOFS: changing to secondary root
ipw3945: Unknown symbol ieee80211_wx_get_encodeext
ipw3945: Unknown symbol ieee80211_wx_set_encode
ipw3945: Unknown symbol ieee80211_wx_get_encode
ipw3945: Unknown symbol ieee80211_txb_free
ipw3945: Unknown symbol ieee80211_wx_set_encodeext
ipw3945: Unknown symbol ieee80211_wx_get_scan
ipw3945: Unknown symbol escape_essid
ipw3945: Unknown symbol ieee80211_freq_to_channel
ipw3945: Unknown symbol ieee80211_set_geo
ipw3945: Unknown symbol ieee80211_rx
ipw3945: Unknown symbol ieee80211_get_channel
ipw3945: Unknown symbol ieee80211_channel_to_index
ipw3945: Unknown symbol ieee80211_rx_mgt
ipw3945: Unknown symbol ieee80211_get_geo
ipw3945: Unknown symbol free_ieee80211
ipw3945: Unknown symbol ieee80211_tx_frame
ipw3945: Unknown symbol ieee80211_is_valid_channel
ipw3945: Unknown symbol ieee80211_get_channel_flags
ipw3945: Unknown symbol alloc_ieee80211
ipw3945: Unknown symbol ieee80211_wx_get_encodeext
ipw3945: Unknown symbol ieee80211_wx_set_encode
ipw3945: Unknown symbol ieee80211_wx_get_encode
ipw3945: Unknown symbol ieee80211_txb_free
ipw3945: Unknown symbol ieee80211_wx_set_encodeext
ipw3945: Unknown symbol ieee80211_wx_get_scan
ipw3945: Unknown symbol escape_essid
ipw3945: Unknown symbol ieee80211_freq_to_channel
ipw3945: Unknown symbol ieee80211_set_geo
ipw3945: Unknown symbol ieee80211_rx
ipw3945: Unknown symbol ieee80211_get_channel
ipw3945: Unknown symbol ieee80211_channel_to_index
ipw3945: Unknown symbol ieee80211_rx_mgt
ipw3945: Unknown symbol ieee80211_get_geo
ipw3945: Unknown symbol free_ieee80211
ipw3945: Unknown symbol ieee80211_tx_frame
ipw3945: Unknown symbol ieee80211_is_valid_channel
ipw3945: Unknown symbol ieee80211_get_channel_flags
ipw3945: Unknown symbol alloc_ieee80211

[infoshirish]

Hey,
Did you installed drivers Wireless LAN? I guess you need to install drivers for your Intel Corporation PRO/Wireless 3945ABG
Network Connection.
I guess for that you need Madwifi. This project provides a Linux kernel device driver for Atheros-based Wireless LAN devices.
check the below links-->
SourceForge.net: MADWIFI
Madwifi - ThinkWiki

Before that check the below links for how to configure wireless connection-->
Wireless-HOWTO
http://www.redhat.com/docs/manuals/l...-wireless.html __________________

[lightsycle]

did you try ndiswrapper? If you are just wanting to get online it works fine. It wouldn't let me use monitor mode on my card tho, and I 'm still having issues with that one. u know I tried madwifi, but I couldn't figure it out. I used ndiswrapper, then removed the mod and linux found my pccard 0_o, now it works, with a few ghosts...