Can't dial out with modem

[dman777]

I'm kind of new to Gentoo and I was wondering if someone could tell me if I have the right drivers for my dial up modem and also if my wifi card should be working. And if so, how do I dial out useing the Gentoo live DVD? Here's the info from lspci and ifconfig, respectuflly:

00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller
00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller
00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 11)
00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI
00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge
00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge
00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller (rev 02)
00:14.6 Modem: ATI Technologies Inc ATI SB400 - AC'97 Modem Controller (rev 02)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc ATI Radeon XPRESS 200M 5955 (PCIE)
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
05:02.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
05:09.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller


eth0 Link encap:Ethernet HWaddr 00:90:4B:F29:E3
BROADCAST NOTRAILERS MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:19 Base address:0x4000

eth1 Link encap:Ethernet HWaddr 00:C0:9F:AA:33:84
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:20 Base address:0x8000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

[tpl]

you ask 2 questions, one about the modem and another about the wifi.

One: yr modem is

00:14.6 Modem: ATI Technologies Inc ATI SB400 - AC'97 Modem Controller (rev 02)

using google "ati sb400 linux" I found

http://www.linuxquestions.org/questi...d.php?t=500990

from which I quote:

> 1) Load module snd_atiixp_modem (after made it)
> 2) The modem is a smartlink modem. With gentoo,
> emerge the ebuild "slmodem" and run ist within
> init. Now you have /dev/modem (points to /dev/ttySL0).
> With debian use slmodem-daemon and maybe
> slmodem-source.
>3) Use /dev/modem

Two: about the wifi: suggest you read the sticky in our "wireless internet" forum: it is very good.