Logitech LX6 Mouse

**Waistless** · 04-18-2008

Hi, I've got a problem with my Logitech LX6 Wireless Mouse

All of the buttons except tilting the mouse wheel right work fine. Clicking the wheel button, scrolling, and tilting the mouse wheel left all work good.

I have not been able to figure out how to get this button working, and I'm almost convinced it's a bug with it being detected (not a problem with X).

Using xev returns all my buttons except the right tilt.

I am using Debian Sid x64 on a 2.6.24-5 kernel.

Using

Code:

od -t x1 < /dev/input/mice

Will again, return all mouse clicks and mouse movement except tilting the mouse wheel to the right. If it's not detected at this level I assume it's a detection problem.

I have tried configuring xorg similar to this: HOWTO Advanced Mouse/Individual Configurations - Gentoo Linux Wiki

But to no avail.

Xorg.conf:

Code:

Section "InputDevice"
    Identifier  "Logitech LX6"
    Driver "evdev"
    Option "Name" "Logitech USB RECEIVER"
    Option "SendCoreEvents"
EndSection

Note that i have changed it to a variety of things. Including...

Code:

Section "InputDevice"
   Identifier  "Mouse0"
   Driver     "mouse"
   Option     "CorePointer"
   Option     "Emulate3Buttons" "false"
   Option     "Device" "/dev/input/mice"
   Option     "Protocol" "auto"
   Option     "Buttons" "7"
   Option     "ZAxisMapping" "4 5"
   Option     "ButtonMapping" "1 2 3 6 7"
EndSection

While playing around with the button mapping such as moving the button positions and changing ZAXIS to 6 7.

The device section may have been different. However, I stress this should not be a problem with X, as the left tilt continues to work with a variety of different configurations. And as I said, trying to use the od command to search for button signals does not return anything for the right tilt.

lsusb:

Code:

Bus 002 Device 005: ID 046d:c50e Logitech, Inc. MX-1000 Cordless Mouse Receiver

My device is detected as an MX-1000, yet despite the warning on the gentoo page, the lmpcm_usb module is not present in lsmod:

Code:

Module                  Size  Used by
isofs                  39720  0 
zlib_inflate           19328  1 isofs
udf                    83368  1 
ipv6                  286248  21 
ppdev                  13832  0 
lp                     17476  0 
ac                     11400  0 
battery                19976  0 
nls_iso8859_1           9728  2 
ntfs                  197216  2 
loop                   22788  0 
firewire_sbp2          20624  0 
dst                    34184  1 
dvb_bt8xx              21892  0 
dvb_core               89388  2 dst,dvb_bt8xx
rt73usb                30848  0 
rt2x00usb              16896  1 rt73usb
rt2x00lib              26752  2 rt73usb,rt2x00usb
bt878                  16232  2 dst,dvb_bt8xx
rfkill                 12816  1 rt2x00lib
bttv                  204404  2 dvb_bt8xx,bt878
input_polldev           9872  1 rt2x00lib
ir_common              42500  1 bttv
mac80211              132236  2 rt2x00usb,rt2x00lib
compat_ioctl32         13184  1 bttv
i2c_algo_bit           11012  1 bttv
videobuf_dma_sg        19076  1 bttv
cfg80211               19856  1 mac80211
nvidiafb               49960  0 
ns558                   9728  0 
snd_hda_intel         362024  3 
videobuf_core          23684  2 bttv,videobuf_dma_sg
btcx_risc               9480  1 bttv
tveeprom               22288  1 bttv
psmouse                45724  0 
snd_mpu401             13992  0 
snd_mpu401_uart        13440  1 snd_mpu401
vgastate               12416  1 nvidiafb
gameport               20496  2 ns558
rtc_cmos               13112  0 
videodev               32256  1 bttv
pcspkr                  7808  0 
v4l2_common            24320  3 bttv,compat_ioctl32,videodev
snd_rawmidi            30624  1 snd_mpu401_uart
snd_seq_device         12948  1 snd_rawmidi
parport_pc             42408  1 
parport                44812  3 ppdev,lp,parport_pc
snd_pcm                89352  1 snd_hda_intel
snd_timer              28552  1 snd_pcm
snd                    65896  13 snd_hda_intel,snd_mpu401,snd_mpu401_uart,snd_rawmidi,snd_seq_device,snd_pcm,snd_timer
soundcore              13216  1 snd
rtc_core               24716  1 rtc_cmos
rtc_lib                 7680  1 rtc_core
v4l1_compat            16388  2 bttv,videodev
rt73                  203776  1 
serio_raw              11908  0 
nvidia               8855748  36 
i2c_nforce2            11136  0 
snd_page_alloc         15248  2 snd_hda_intel,snd_pcm
k8temp                 10496  0 
firmware_class         15104  4 dvb_bt8xx,rt2x00lib,bttv,rt73
i2c_core               29824  7 dst,dvb_bt8xx,bttv,i2c_algo_bit,tveeprom,nvidia,i2c_nforce2
button                 13984  0 
evdev                  17024  4 
ext3                  139024  2 
jbd                    55976  1 ext3
mbcache                13952  1 ext3
sd_mod                 33536  6 
ide_cd                 44704  1 
cdrom                  39464  1 ide_cd
sata_nv                33032  5 
ata_generic            13060  0 
libata                162736  2 sata_nv,ata_generic
scsi_mod              170296  3 firewire_sbp2,sd_mod,libata
usbhid                 35168  0 
hid                    41792  1 usbhid
floppy                 66664  0 
firewire_ohci          24192  0 
firewire_core          49472  2 firewire_sbp2,firewire_ohci
crc_itu_t               6656  2 rt2x00lib,firewire_core
forcedeth              54540  0 
generic                 9732  0 [permanent]
ehci_hcd               39692  0 
amd74xx                14360  0 [permanent]
ide_core              144920  3 ide_cd,generic,amd74xx
ohci_hcd               28164  0 
thermal                22688  0 
processor              45032  1 thermal
fan                     9864  0

Output of dmesg:

Code:

mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 316k freed
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (40 C)
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xfe02f000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp: the driver 'ide' has been registered
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NFORCE-MCP51: IDE controller (0x10de:0x0265 rev 0xa1) at  PCI slot 0000:00:0d.0
NFORCE-MCP51: not 100% native mode: will probe irqs later
NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
    ide0: BM-DMA at 0xf400-0xf407, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf408-0xf40f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
usb 1-3: new full speed USB device using ohci_hcd and address 2
usb 1-3: configuration #1 chosen from 1 choice
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 4 ports detected
Probing IDE interface ide1...
usb 1-4: new low speed USB device using ohci_hcd and address 3
usb 1-4: configuration #1 chosen from 1 choice
usb 1-3.1: new full speed USB device using ohci_hcd and address 4
hdc: HL-DT-STDVD-RAM GSA-H20L, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: irq 22, io mem 0xfe02e000
usb 1-3.1: configuration #1 chosen from 1 choice
usb 1-3.1: can't set config #1, error -62
hub 1-3:1.0: hub_port_status failed (err = -62)
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 1-3:1.0: hub_port_status failed (err = -62)
hub 1-3:1.0: hub_port_status failed (err = -62)
usb 1-3: USB disconnect, address 2
usb 1-3.1: USB disconnect, address 4
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:14.0 to 64
SCSI subsystem initialized
libata version 3.00 loaded.
usb 1-4: USB disconnect, address 3
usb 2-3: new high speed USB device using ehci_hcd and address 2
forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:17:31:ea:51:cf
forcedeth 0000:00:14.0: highdma pwrctl timirq gbit lnktim desc-v3
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:04:05.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
usb 2-3: configuration #1 chosen from 1 choice
hub 2-3:1.0: USB hub found
hub 2-3:1.0: 4 ports detected
firewire_ohci: Added fw-ohci device 0000:04:05.0, OHCI version 1.10
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:0e.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xe000 irq 20
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xe008 irq 20
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
usb 2-3.1: new high speed USB device using ehci_hcd and address 4
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
firewire_core: created new fw device fw0 (0 config rom retries, S400)
ata1.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
usb 2-3.1: configuration #1 chosen from 1 choice
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      ST3250620AS      3.AA PQ: 0 ANSI: 5
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:0f.0 to 64
usb 2-3.2: new low speed USB device using ehci_hcd and address 5
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xcc00 irq 23
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xcc08 irq 23
usb 2-3.2: configuration #1 chosen from 1 choice
ata3: SATA link down (SStatus 0 SControl 300)
usb 2-3.3: new low speed USB device using ehci_hcd and address 6
usb 2-3.3: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
ata4: SATA link down (SStatus 0 SControl 300)
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 sda6 sda7 > sda4
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-4: new low speed USB device using ohci_hcd and address 5
usb 1-4: configuration #1 chosen from 1 choice
input: Logitech USB RECEIVER as /class/input/input1
input,hidraw0: USB HID v1.11 Mouse [Logitech USB RECEIVER] on usb-0000:00:0b.1-3.2
input: Twinhan Tech Remote Control as /class/input/input2
input,hidraw1: USB HID v1.10 Keyboard [Twinhan Tech Remote Control] on usb-0000:00:0b.1-3.3
input: Twinhan Tech Remote Control as /class/input/input3
input,hidraw2: USB HID v1.10 Mouse [Twinhan Tech Remote Control] on usb-0000:00:0b.1-3.3
input: Logitech Logitech USB Keyboard as /class/input/input4
input,hidraw3: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:0b.0-4
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input6
ACPI: Power Button (CM) [PWRB]
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:03:00.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  169.12  Thu Feb 14 17:51:09 PST 2008
rt73: init
rt73: idVendor = 0x7d1, idProduct = 0x3c03 
pnp: the driver 'parport_pc' has been registered
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
rt73: using permanent MAC addr
rt73: Active MAC addr: 00:1b:11:bb:6e:37
rt73: Local MAC = 00:1b:11:bb:6e:37
usbcore: registered new interface driver rt73
parport_pc 00:0a: driver attached
input: PC Speaker as /class/input/input7
Linux video capture interface: v2.00
pnp: the driver 'rtc_cmos' has been registered
rtc_cmos 00:04: disabling not supported
rtc_cmos: probe of 00:04 failed with error -16
pnp: the driver 'mpu401' has been registered
mpu401 00:0b: driver attached
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:10.1 to 64
pnp: the driver 'ns558' has been registered
ns558 00:0c: driver attached
gameport: NS558 PnP Gameport is pnp00:0c/gameport0, io 0x201, speed 638kHz
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:04:09.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
bttv0: Bt878 (rev 17) at 0000:04:09.0, irq: 17, latency: 32, mmio: 0xfdbff000
bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001
bttv0: using: Twinhan DST + clones [card=113,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00f500ff [init]
bttv0: tuner absent
bttv0: add subdevice "dvb0"
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:04:09.1[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
bt878_probe: card id=[0x11822],[ Twinhan VisionPlus DVB ] has DVB functions.
bt878(0): Bt878 (rev 17) at 04:09.1, irq: 17, latency: 32, memory: 0xfdbfe000
usbcore: registered new interface driver rt73usb
DVB: registering new adapter (bttv0)
dst(0) dst_get_device_id: Recognise [DTTDIG]
DST type flags : 0x10 firmware version = 2
dst(0) dst_get_mac: MAC Address=[00:08:ca:18:7e:00]
DVB: registering frontend 0 (DST DVB-T)...
Adding 2474000k swap on /dev/sda4.  Priority:-1 extents:1 across:2474000k
EXT3 FS on sda7, internal journal
loop: module loaded
NTFS driver 2.1.29 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs warning (device sda1): load_system_files(): Unsupported volume flags 0x4000 encountered.
NTFS-fs error (device sda1): load_system_files(): Volume has unsupported flags set.  Mounting read-only.  Run chkdsk and mount in Windows.
NTFS volume version 3.1.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
UDF-fs: Partition marked readonly; forcing readonly mount
UDF-fs INFO UDF 0.9.8.1 (2004/29/09) Mounting volume 'WIC', timestamp 2007/08/03 07:52 (1258)
rt73: driver version - 1.0.3.6 CVS
rt73: using net dev supplied MAC addr
rt73: Active MAC addr: 00:1b:11:bb:6e:37
rt73: Local MAC = 00:1b:11:bb:6e:37
wlan0: no IPv6 routers present
NOHZ: local_softirq_pending 08
NOHZ: local_softirq_pending 08
NOHZ: local_softirq_pending 08
NOHZ: local_softirq_pending 08
NOHZ: local_softirq_pending 08
NOHZ: local_softirq_pending 08
NOHZ: local_softirq_pending 08
NOHZ: local_softirq_pending 08
NOHZ: local_softirq_pending 08
NOHZ: local_softirq_pending 08

Sorry if the post is long, but I hope i've given you enough information. Would someone be willing to help? Thanks

**tophill** · 09-10-2008

I have the same problem. Did you, or anyone, ever solve this?

**Waistless** · 09-13-2008

No, assuming it's a bug, I have no idea where to report it. I'm guessing if the problem is a kernel module, I'd have to find the nearest relevant launchpad.

**uop** · 10-11-2008

Here's the solution: KODA ? Using a Logitech LX7 mouse in Ubuntu Edgy: “IHATEKLUDGERS”

Thread Tools

Display

Logitech LX6 Mouse

Posting Permissions