I have been trying to get my CDMA EV-DO card to be recognize by linux. But i am not getting anywhere. Here is the put put of /var/log/messages when i insert my EVDO PCI card.
So what i gather afterreading around is that linux is assigning the wrong IRQ address to the card (its assigning IRQ 10 rather than 9).
any ideas if that is the problem or is there any other problem? and how do i get about it? Thx a lot
rohan

Jun 20 17:08:55 localhost kernel: cs: cb_alloc(bus 3): vendor 0x11c1, device 0x5802
Jun 20 17:08:55 localhost kernel: PCI: Enabling device 03:00.0 (0000 -> 0002)
Jun 20 17:08:55 localhost kernel: usb-ohci.c: USB OHCI at membase 0xc893e000, IRQ 10
Jun 20 17:08:55 localhost kernel: usb-ohci.c: usb-03:00.0, PCI device 11c1:5802
Jun 20 17:08:55 localhost kernel: usb.c: new USB bus registered, assigned bus number 3
Jun 20 17:08:55 localhost kernel: hub.c: USB hub found
Jun 20 17:08:55 localhost kernel: hub.c: 2 ports detected
Jun 20 17:08:56 localhost /etc/hotplug/pci.agent: Setup usb-ohci for PCI slot 03:00.0
Jun 20 17:08:56 localhost devlabel: devlabel service started/restarted
Jun 20 17:08:58 localhost kernel: hub.c: new USB device 03:00.0-1, assigned address 2
Jun 20 17:08:58 localhost /etc/hotplug/usb.agent: Setup usbcore for USB product 0/0/0
Jun 20 17:08:58 localhost /etc/hotplug/usb.agent: Setup usbcore for USB product 0/0/0
Jun 20 17:08:59 localhost kernel: usb.c: USB device not accepting new address=2 (error=-110)
Jun 20 17:08:59 localhost devlabel: devlabel service started/restarted
Jun 20 17:09:00 localhost kernel: hub.c: Cannot enable port 1 of hub 1, disabling port.
Jun 20 17:09:00 localhost kernel: hub.c: Maybe the USB cable is bad?
Jun 20 17:09:00 localhost kernel: hub.c: new USB device 03:00.0-1, assigned address 3
Jun 20 17:09:00 localhost kernel: usb.c: USB device 3 (vend/prod 0xf3d/0x112) is not claimed by any active driver.
Jun 20 17:09:03 localhost /etc/hotplug/usb.agent: ... no modules for USB product f3d/112/1



the follwing is the output of /proc/bus/usb/devices after the PCI card is plugged in


> T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
> B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
> D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> P: Vendor=0000 ProdID=0000 Rev= 0.00
> S: Product=USB OHCI Root Hub
> S: SerialNumber=c893e000
> C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
> T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
> D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=16 #Cfgs= 1
> P: Vendor=0f3d ProdID=0112 Rev= 0.01
> S: Manufacturer=AirPrime, Incorporated
> S: Product=AirPrime CDMA Wireless PC Card
> C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=100mA
> I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
> E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=128ms
> E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=0b(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms


there are 2 places with (none).. how do i get past that?