Serial port not working
Serial port on my KUBUNTU doesn't seem to be working. This is the first time I am trying to use serial port on Linux so I might be doing something stupid.
I have attached a loop-back on my serial port to check if data is actually transmitted and received. From looking at /proc/tty/driver/serial it looks like data is being transmitted but nothing is being received, however voltmeter doesn't show any fluctuation when data is being transmitted so I doubt if any data is 'actually' being transmitted.
Here are the results of dmesg, setserial, stty, etc
dmesg | grep tty:
[ 0.010000] console [tty0] enabled
[ 1.551851] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.552105] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ls -l /dev/ttyS*:
crw-rw-rw- 1 sanket dialout 4, 64 2009-05-13 13:17 /dev/ttyS0
crw-rw---- 1 root dialout 4, 65 2009-05-13 11:38 /dev/ttyS1
crw-rw---- 1 root dialout 4, 66 2009-05-13 11:38 /dev/ttyS2
crw-rw---- 1 root dialout 4, 67 2009-05-13 11:38 /dev/ttyS3
stty -F /dev/ttyS0 -a:
speed 9600 baud; rows 0; columns 0; line = 0;
intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = <undef>; eol2 = <undef>; swtch = <undef>; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R;
werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 0;
-parenb -parodd cs8 hupcl -cstopb cread clocal -crtscts
-ignbrk -brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon -ixoff -iuclc -ixany -imaxbel -iutf8
opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0
isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt echoctl echoke
/dev/ttyS0, Line 0, UART: 16550A, Port: 0x03f8, IRQ: 4
Baud_base: 9600, close_delay: 50, divisor: 0
Flags: spd_normal auto_irq
00:0c PNP0501 16550A-compatible serial port
state = active
00:01.0 ISA bridge: nVidia Corporation MCP78S [GeForce 8200] LPC Bridge (rev a2)
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:67963 rx:0
1: uart:unknown port:000002F8 irq:3
2: uart:unknown port:000003E8 irq:4
3: uart:unknown port:000002E8 irq:3
As you can see this shows transmitted data but received data is 0, which cant be the case as all the data transmitted should be received due to loopback.
I have checked BIOS and it shows serial port on IRQ 4 and address 0x3F8.
I am transmitting data using echo test_message > /dev/ttyS0, cp filename /dev/ttyS0 and by using minicom, cutecom.
I am trying to receive data using tail -f /dev/ttyS0, cat /dev/ttyS0 and using cutecom application.
I have wasted two days with this without any progress.