Find the answer to your Linux question:
Page 2 of 2 FirstFirst 1 2
Results 11 to 20 of 20
Same thing is still happening. Code: # Xorg configuration created by pyxf86config Section "ServerLayout" Identifier "Default Layout" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "InputDevice" Identifier "Keyboard0" ...
Enjoy an ad free experience by logging in. Not a member yet? Register.
  1. #11
    Just Joined!
    Join Date
    Apr 2007
    Posts
    10

    Thumbs up


    Same thing is still happening.

    Code:
    # Xorg configuration created by pyxf86config
    
    Section "ServerLayout"
    	Identifier "Default Layout"
    	Screen 0 "Screen0" 0 0
    	InputDevice "Keyboard0" "CoreKeyboard"
    EndSection
    
    Section "InputDevice"
    	Identifier "Keyboard0"
    	Driver "kbd"
    	Option "XkbModel" "pc105"
    	Option "XkbLayout" "us"
    EndSection
    
    Section "Monitor"
    	Identifier   "Monitor0"
    	ModelName    "Monitor xxx"
    	HorizSync    30.0 - 61.0
    	VertRefresh  50.0 - 95.0
    	Option	    "dpms"
    EndSection
    
    Section "Device"
    	Identifier "Videocard0"
    	Driver "vesa"
    EndSection
    
    Section "Screen"
    	Identifier "Screen0"
    	Device     "Videocard0"
    	Monitor    "Monitor0"
    	DefaultDepth     24
    	SubSection "Display"
    		Viewport   0 0
    		Depth     24
    		Modes    "1024x768" "800x600" "640x480"
    	EndSubSection
    EndSection

  2. #12
    Super Moderator devils casper's Avatar
    Join Date
    Jun 2006
    Location
    Chandigarh, India
    Posts
    24,729
    does 'system-config-display' command throw any error message?
    what about 'startx'?
    It is amazing what you can accomplish if you do not care who gets the credit.
    New Users: Read This First

  3. #13
    Just Joined!
    Join Date
    Mar 2007
    Posts
    10
    X Server log may have some info about this error, Have to checked the log for any error message? Log location is in the screen shot attached by you...

  4. $spacer_open
    $spacer_close
  5. #14
    Just Joined!
    Join Date
    Apr 2007
    Posts
    10
    There isn't any log file at that location. However I found some X log files in /var/log.

    Running it over real quick (near the bottom), I found this, which could be the problem:

    (EE) AIGLX: Screen 0 is not DRI capable

    Here is the log file.

  6. #15
    Just Joined!
    Join Date
    Apr 2007
    Posts
    10
    No one has any idea?

  7. #16
    Super Moderator devils casper's Avatar
    Join Date
    Jun 2006
    Location
    Chandigarh, India
    Posts
    24,729
    (EE) AIGLX: Screen 0 is not DRI capable
    did you install AIGLX? add this code at the end of xorg.conf file.
    Code:
    Section "DRI"
      Mode 0666
    EndSection
    It is amazing what you can accomplish if you do not care who gets the credit.
    New Users: Read This First

  8. #17
    Just Joined!
    Join Date
    Apr 2007
    Posts
    10
    If AIGLX wasn't installed during the linux installation, then chances of it being installed are pretty low.

    I tried adding that to the xorg.conf file, but again no dice.

    I looked at the AIGLX documentation and it showed the section necessary for disabling AIGLX, and after adding that in, I still get the Blank Screen/No Signal. However I don't see any errors in the log files. (Presuming that errors are makred by "(EE)")

  9. #18
    Super Moderator devils casper's Avatar
    Join Date
    Jun 2006
    Location
    Chandigarh, India
    Posts
    24,729
    execute this
    Code:
    lspci | grep VGA
    post output here.
    It is amazing what you can accomplish if you do not care who gets the credit.
    New Users: Read This First

  10. #19
    Just Joined!
    Join Date
    Apr 2007
    Posts
    10
    Code:
    01:00.0 VGA compatible controller nVidia Corporation Unknown device 0193 (rev 2)

  11. #20
    Super Moderator devils casper's Avatar
    Join Date
    Jun 2006
    Location
    Chandigarh, India
    Posts
    24,729
    execute this
    Code:
    system-config-display --reconfig
    01:00.0 VGA compatible controller nVidia Corporation Unknown device 0193 (rev 2)
    boot up in command line mode and
    Fedora is not recognizing your Graphics Card. i suggest you try any LiveCD and check if Graphics works in Live environment.
    It is amazing what you can accomplish if you do not care who gets the credit.
    New Users: Read This First

Page 2 of 2 FirstFirst 1 2

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •