Hi,
I am a newbie to linux. I was trying to get a Lite5200B board runing with Linux. I downloaded "Ltib" and was trying to build the kernel and u-boot, but the kernel kept hanging. I also changed the baud-rate for the console to 115200, but still was not able to move forward.
I looked up with some forums and tried the things mentioned there, but was still not able to move forward. Please help.

Thanks for the help.




U-Boot 1.1.5 (Feb 12 2009 - 12:00:40)

CPU: MPC5200 v2.2, Core v1.4 at 462 MHz
Bus 132 MHz, IPB 132 MHz, PCI 33 MHz
Board: Freescale Lite5200B
I2C: 85 kHz, ready
DRAM: 256 MB
FLASH: 32 MB
*** Warning - bad CRC, using default environment

*** Using default MAC address from the EEPROM: 00:04:9f:00:6d:bc ***

PCI: Bus Dev VenId DevId Class Int
00 1a 1057 5809 0680 00
In: serial
Out: serial
Err: serial
Net: FEC ETHERNET
IDE: Bus 0: OK
Device 0: not available
Device 1: not available

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot: 0
=>
=> setenv kernel_addr FE000000
=> dhcp
Unknown command 'dhcp' - try 'help'
=>
=> printenv
bootcmd=run flash_self
bootdelay=5
baudrate=115200
preboot=echo;echo Type "run flash_nfs" to mount root filesystem over NFS;echo
netdev=eth0
nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}
ramargs=setenv bootargs root=/dev/ram rw
addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:$ {hostname}:${netdev}:off panic=1
flash_nfs=run nfsargs addip;bootm ${kernel_addr}
flash_self=run ramargs addip;bootm ${kernel_addr} ${ramdisk_addr}
net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm
rootpath=/opt/eldk/ppc_82xx
bootfile=/tftpboot/MPC5200/uImage
ethaddr=00:04:9f:00:6d:bc
stdin=serial
stdout=serial
stderr=serial
ethact=FEC ETHERNET
kernel_addr=FE000000

Environment size: 713/65532 bytes
=> setenv ramdisk_addr FE200000
=> run flash_self
## Booting image at fe000000 ...
Image Name: Linux-2.6.16.11-rt18
Created: 2009-03-25 7:08:08 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1327760 Bytes = 1.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at fe200000 ...
Image Name: uboot ext2 ramdisk rootfs
Created: 2009-03-23 11:26:15 UTC
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 4846432 Bytes = 4.6 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Ramdisk to 0faad000, end 0ff4c360 ... OK
id mach(): done
MMU:enter
MMU:hw init
MMU:mapin
MMU:setio
MMU:exit
setup_arch: enter
setup_arch: bootmem
arch: exit