Results 1 to 9 of 9
Thread: Mp3 usb player does not mount
|
Enjoy an ad free experience by logging in. Not a member yet? Register.
|
|
-
06-19-2006 #1
- Join Date
- Mar 2005
- Posts
- 14
Mp3 usb player does not mount
from 2 weeks to now, I can mount my mp3 usb player. The conection is ok, cause I can mount another mp3 player in the same usb and the mp3 player is also ok because I can mount it in my work's computer.
I've tried to mount it but the system has not the /dev/sda device.
Any ideas ?
Thanks a lot !!!
-
06-19-2006 #2
Can you give us more details than that? What brand of player is it? Does it require some sort of software to access it or can you just load it like a USB harddrive? What are the exact messages you're getting when you run dmesg after plugging it in? What version of Mandriva are you using?
Registered Linux user #270181
-
06-19-2006 #3
- Join Date
- Mar 2005
- Posts
- 14
Hello again,
the mplayer is very old nowadays. I've been using it as a usb storage without any problems until now and without any special software.
Here you have some commands:
#uname -a
Linux rodogh 2.6.11-6mdk #1 Tue Mar 22 16:04:32 CET 2005 i686 Pentium III (Katmai) unknown GNU/Linux
#dmesg
...
usb 1-1: new full speed USB device using uhci_hcd and address 8
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 8
usb-storage: waiting for device to settle before scanning
Vendor: A-MAX Model: PA22 MP3 Player Rev: 0001
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 256001 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 04
sda: assuming drive cache: write through
SCSI device sda: 256001 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 04
sda: assuming drive cache: write through
/dev/scsi/host1/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0
Thanks again !!!
-
06-19-2006 #4
what happens if you reboot with it plugged in? i had a usb drive that wouldn't mount but when i booted with it plugged in i never had problems after that.
Desktop: Dual Xeon 2.8 GHz 1.5 GB RAM Ubuntu/XP Pro
Laptop: Macbook 2 GHz C2Duo 3 GB RAM OS X/ Ubuntu/ XP Pro
Linux Registration #396559
Go 'Stros!
-
06-19-2006 #5
- Join Date
- Mar 2005
- Posts
- 14
I thing it must run without rebooting...
Sorry, but there were more messages with dmesg command:
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
Vendor: A-MAX Model: PA22 MP3 Player Rev: 0001
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 256001 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 04
sda: assuming drive cache: write through
SCSI device sda: 256001 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 04
sda: assuming drive cache: write through
/dev/scsi/host2/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi2, channel 0, id 0, lun 0, type 0
usb 1-1: reset full speed USB device using uhci_hcd and address 13
usb 1-1: device not accepting address 13, error -71
usb 1-1: reset full speed USB device using uhci_hcd and address 13
usb 1-1: device not accepting address 13, error -71
usb 1-1: reset full speed USB device using uhci_hcd and address 13
usb 1-1: device descriptor read/64, error -71
usb 1-1: device descriptor read/64, error -71
usb 1-1: reset full speed USB device using uhci_hcd and address 13
usb 1-1: device descriptor read/64, error -71
usb 1-1: device descriptor read/64, error -71
scsi: Device offlined - not ready after error recovery: host 2 channel 0 id 0 lun 0
scsi2 (0:0): rejecting I/O to offline device
usb 1-1: USB disconnect, address 13
scsi2 (0:0): rejecting I/O to offline device
scsi2 (0:0): rejecting I/O to offline device
usb-storage: device scan complete
usb 1-1: new full speed USB device using uhci_hcd and address 14
usb 1-1: device not accepting address 14, error -71
usb 1-1: new full speed USB device using uhci_hcd and address 15
usb 1-1: device not accepting address 15, error -71
usb 1-1: new full speed USB device using uhci_hcd and address 16
usb 1-1: device descriptor read/64, error -71
usb 1-1: device descriptor read/64, error -71
usb 1-1: new full speed USB device using uhci_hcd and address 17
usb 1-1: device descriptor read/64, error -71
usb 1-1: device descriptor read/64, error -71
-
06-20-2006 #6Code:
usb 1-1: new full speed USB device using uhci_hcd and address 8 scsi1 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 8 usb-storage: waiting for device to settle before scanning Vendor: A-MAX Model: PA22 MP3 Player Rev: 0001 Type: Direct-Access ANSI SCSI revision: 04 SCSI device sda: 256001 512-byte hdwr sectors (131 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 04 sda: assuming drive cache: write through SCSI device sda: 256001 512-byte hdwr sectors (131 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 04 sda: assuming drive cache: write through /dev/scsi/host1/bus0/target0/lun0: p1 Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0
Registered Linux user #270181
-
06-20-2006 #7
- Join Date
- Mar 2005
- Posts
- 14
It seems to be something in /dev/sda because of the line you've read
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
But waiting just some seconds it appears another lines telling that something is wrong... (just see my last post)
scsi: Device offlined - not ready after error recovery: host 2 channel 0 id 0 lun 0
scsi2 (0:0): rejecting I/O to offline device
usb 1-1: USB disconnect, address 13
So if I try to do what you said I get "no device" message (in spanish....)
mount: el dispositivo especial /dev/sda no existe
Kind regards !!!
-
06-20-2006 #8
- Join Date
- Mar 2005
- Posts
- 14
Hi again,
just only to say that I restored a O.S's backup and now it runs perfectly. The problem ? I don't know...
If I do a dmesg this is what it happens:
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 9
usb-storage: waiting for device to settle before scanning
Vendor: A-MAX Model: PA22 MP3 Player Rev: 0001
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 256001 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 04
sda: assuming drive cache: write through
SCSI device sda: 256001 512-byte hdwr sectors (131 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 04
sda: assuming drive cache: write through
/dev/scsi/host2/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0
usb-storage: device scan complete
If anyone want to know about my new configuration, just let me know...
Thanks to you all...
-
06-20-2006 #9
Well, umm... YEAH! See, just like I said! I mean... umm..
But seriously, good to see it's working now, but I can't for the life of me figure out what might have gone wrong in the first place. Perhaps you updated a software package that conflicted with something else? I'm really shooting in the dark here, but good to hear it's working now.Registered Linux user #270181