Find the answer to your Linux question:
Results 1 to 5 of 5
Hi folks, Ubuntu 8.04 desktop amd64 SATA Sony DVD burner cdrecord -version Code: Cdrecord-yelling-line-to-tell-frontends-to-use-it-like-version 2.01.01a03-dvd Wodim 1.1.6 On running; $ cdrecord -scanbus Code: scsibus5: 5,0,0 500) 'SONY ' 'DVD RW ...
Enjoy an ad free experience by logging in. Not a member yet? Register.
  1. 08-17-2008 #1
    satimis
    satimis is offline
    Linux Guru
    Join Date
    Sep 2004
    Posts
    1,712

    Problem on burning CD

    Hi folks,


    Ubuntu 8.04 desktop amd64
    SATA Sony DVD burner

    cdrecord -version
    Code:
    Cdrecord-yelling-line-to-tell-frontends-to-use-it-like-version 2.01.01a03-dvd 
Wodim 1.1.6
    On running;

    $ cdrecord -scanbus
    Code:
    scsibus5:
	5,0,0	500) 'SONY    ' 'DVD RW AW-G170S ' '1.72' Removable CD-ROM
	5,1,0	501) *
	5,2,0	502) *
	5,3,0	503) *
	5,4,0	504) *
	5,5,0	505) *

    $ cdrecord -v -eject -tao dev=5,0,0 /path/to/ubuntu-8.04.1-desktop-i386.iso
    Code:
    TOC Type: 1 = CD-ROM
wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.scsidev: '5,0,0'
scsibus: 5 target: 0 lun: 0
WARNING: the deprecated pseudo SCSI syntax found as device specification.
Support for that may cease in the future versions of wodim. For now,
the device will be mapped to a block device file where possible.
Run "wodim --devices" for details.
    $ wodim -v -checkdrive dev=/dev/scd0
    Code:
    TOC Type: 1 = CD-ROM
scsidev: '/dev/scd0'
devname: '/dev/scd0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'SONY    '
Identification : 'DVD RW AW-G170S '
Revision       : '1.72'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x002B (DVD+R/DL) 
Profile: 0x001B (DVD+R) 
Profile: 0x001A (DVD+RW) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x0012 (DVD-RAM) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R) 
Profile: 0x0008 (CD-ROM) (current)
Profile: 0x0002 (Removable disk) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 890880 = 870 KB
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
    Please advise how to fix the problem. TIA


    B.R.
    satimis
    Reply With Quote Reply With Quote
  2. 08-17-2008 #2
    hazel
    hazel is offline
    Linux Engineer hazel's Avatar
    Join Date
    May 2004
    Location
    Harrow, UK
    Posts
    1,081
    I think you need root access to record. Also wodim uses Linux device names rather than the scsi x,y,z convention. So sudo wodim -v -eject -tao dev=/dev/scd0 /path/to/ubuntu-8.04.1-desktop-i386.iso should do it.
    "I'm just a little old lady; don't try to dazzle me with jargon!"
    Reply With Quote Reply With Quote
  3. 08-18-2008 #3
    satimis
    satimis is offline
    Linux Guru
    Join Date
    Sep 2004
    Posts
    1,712
    Quote Originally Posted by hazel View Post
    I think you need root access to record. Also wodim uses Linux device names rather than the scsi x,y,z convention. So sudo wodim -v -eject -tao dev=/dev/scd0 /path/to/ubuntu-8.04.1-desktop-i386.iso should do it.
    Hi hazel,


    Thanks for your advice.


    $ sudo wodim -v -eject -tao dev=/dev/scd0 Desktop/archlinux-2008.06-core-x86_64.iso
    Code:
    TOC Type: 1 = CD-ROM
scsidev: '/dev/scd0'
devname: '/dev/scd0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'SONY    '
Identification : 'DVD RW AW-G170S '
Revision       : '1.72'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x002B (DVD+R/DL) 
Profile: 0x001B (DVD+R) 
Profile: 0x001A (DVD+RW) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x0012 (DVD-RAM) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R) 
Profile: 0x0008 (CD-ROM) (current)
Profile: 0x0002 (Removable disk) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 890880 = 870 KB
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
FIFO size      : 12582912 = 12288 KB
Track 01: data   305 MB        
Total size:      350 MB (34:42.81) = 156211 sectors
Lout start:      350 MB (34:44/61) = 156211 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 2
  Reference speed: 6
  Is not unrestricted
  Is erasable
  Disk sub type: High speed Rewritable (CAV) media (1)
  ATIP start of lead in:  -11615 (97:27/10)
  ATIP start of lead out: 335925 (74:41/00)
  1T speed low:  4 1T speed high: 10
  2T speed low:  4 2T speed high:  0 (reserved val  6)
  power mult factor: 1 5
  recommended erase/write power: 5
  A1 values: 24 1A D9
  A2 values: 26 B2 48
Disk type:    Phase change
Manuf. index: 18
Manufacturer: Plasmon Data systems Ltd.
Blocks total: 335925 Blocks current: 335925 Blocks remaining: 179714
Speed set to 1764 KB/s
Starting to write CD/DVD at speed  10.0 in real TAO mode for single session.
Last chance to quit, starting real write i   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 0
Track 01:   75 of  305 MB written (fifo 100%) [buf 100%]  10.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 97 F9 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 03 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.041s timeout 40s

write track data: error after 79677440 bytes
wodim: A write error occured.
wodim: Please properly read the error message above.
Writing  time:   72.741s
Average write speed  35.7x.
Min drive buffer fill was 100%
Fixating...
Fixating time:   33.499s
BURN-Free was 1 times used.
wodim: fifo had 1446 puts and 1256 gets.
wodim: fifo was 0 times empty and 1241 times full, min fill was 93%.

    However no problem occurred on blanking the CD-RW

    $ sudo wodim -v -eject -tao dev=/dev/scd0 blank=all
    Code:
    TOC Type: 1 = CD-ROM
scsidev: '/dev/scd0'
devname: '/dev/scd0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'SONY    '
Identification : 'DVD RW AW-G170S '
Revision       : '1.72'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x002B (DVD+R/DL) 
Profile: 0x001B (DVD+R) 
Profile: 0x001A (DVD+RW) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x0012 (DVD-RAM) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R) 
Profile: 0x0008 (CD-ROM) (current)
Profile: 0x0002 (Removable disk) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 890880 = 870 KB
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 2
  Reference speed: 6
  Is not unrestricted
  Is erasable
  Disk sub type: High speed Rewritable (CAV) media (1)
  ATIP start of lead in:  -11615 (97:27/10)
  ATIP start of lead out: 335925 (74:41/00)
  1T speed low:  4 1T speed high: 10
  2T speed low:  4 2T speed high:  0 (reserved val  6)
  power mult factor: 1 5
  recommended erase/write power: 5
  A1 values: 24 1A D9
  A2 values: 26 B2 48
Disk type:    Phase change
Manuf. index: 18
Manufacturer: Plasmon Data systems Ltd.
Speed set to 1764 KB/s
Starting to write CD/DVD at speed  10.0 in real BLANK mode for single session.
Last chance to quit, starting real write i   0 seconds. Operation starts.
Performing OPC...
Blanking entire disk
Blanking time:  481.895s
    B.R.
    satimis
    Reply With Quote Reply With Quote
  4. 08-18-2008 #4
    daark.child
    daark.child is offline
    Blackfooted Penguin daark.child's Avatar
    Join Date
    Apr 2006
    Location
    West Yorks
    Posts
    4,372
    Have you tried using a different disc. It seems like 75MB is successfully written to the disc and then some sort of writing problem occurs.
    Reply With Quote Reply With Quote
  5. 08-18-2008 #5
    satimis
    satimis is offline
    Linux Guru
    Join Date
    Sep 2004
    Posts
    1,712
    Quote Originally Posted by daark.child View Post
    Have you tried using a different disc. It seems like 75MB is successfully written to the disc and then some sort of writing problem occurs.
    Hi daark.child,


    It is not the problem of the CD-RW. I found the trick. "-tao" should be dropped.


    $ wodim -eject -v dev=/dev/scd0 Desktop/archlinux-2008.06-core-x86_64.iso
    Code:
    ......
Starting to write CD/DVD at speed  10.0 in real TAO mode for single session.
......
    Wodim also works as USER. Thanks


    satimis
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules