Find the answer to your Linux question:
Page 2 of 2 FirstFirst 1 2
Results 11 to 20 of 20
What are the output of Code: lspci and Code: dmesg...
  1. 08-09-2005 #11
    Kingedgar
    Kingedgar is offline
    Just Joined!
    Join Date
    Nov 2004
    Location
    Iowa
    Posts
    43
    What are the output of

    Code:
    lspci
    and

    Code:
    dmesg
    Reply With Quote Reply With Quote
  2. 08-10-2005 #12
    COKE CAN
    COKE CAN is offline
    Linux Newbie
    Join Date
    Jun 2005
    Location
    Yorktown, VA
    Posts
    215
    Code:
    # lspci
0000:00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
0000:00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 05)
0000:00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 05)
0000:00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 05)
0000:00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #1) (rev 05)
0000:00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 05)
0000:00:1f.4 USB Controller: Intel Corp. 82801BA/BAM USB (Hub #2) (rev 05)
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801BA/BAM AC'97 Audio (rev 05)
0000:00:1f.6 Modem: Intel Corp. Intel 537 [82801BA/BAM AC'97 Modem] (rev 05)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY
0000:02:00.0 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
0000:02:00.1 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
0000:02:08.0 Ethernet controller: Intel Corp. 82801BA/BAM/CA/CAM Ethernet Controller (rev 03)
0000:02:0a.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
    Code:
    # dmesg
Linux version 2.6.8-2-686 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 Thu May 19 17:53:30 JST 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
 BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
 BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002fef0000 (usable)
 BIOS-e820: 000000002fef0000 - 000000002feff000 (ACPI data)
 BIOS-e820: 000000002feff000 - 000000002ff00000 (ACPI NVS)
 BIOS-e820: 000000002ff00000 - 000000002ff80000 (usable)
 BIOS-e820: 000000002ff80000 - 0000000030000000 (reserved)
 BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
767MB LOWMEM available.
On node 0 totalpages: 196480
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 192384 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 TOSCPL                                    ) @ 0x000f6da0
ACPI: RSDT (v001 TOSCPL   RSDT   0x06040000  LTP 0x00000000) @ 0x2fefa617
ACPI: FADT (v001 TOSCPL BTR20    0x06040000 PTL  0x00000001) @ 0x2fefef64
ACPI: BOOT (v001 TOSCPL $SBFTBL$ 0x06040000  LTP 0x00000001) @ 0x2fefefd8
ACPI: DSDT (v001 COMPAL BTR20    0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro
No local APIC present or hardware disabled
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 1994.128 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 770860k/785920k available (1551k kernel code, 14228k reserved, 690k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3948.54 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 3febf9ff 00000000 00000000 00000000
CPU: After vendor identify, caps:  3febf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps:        3febf9ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
CPU: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4528k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd990, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SLOT._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *5)
ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs *5)
ACPI: PCI Interrupt Link [LNKE] (IRQs *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 5) *11
ACPI: Embedded Controller [EC0] (gpe 28)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f6e00
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9cb6, dseg 0x400
pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0a: ioport range 0x1000-0x105f has been reserved
pnp: 00:0a: ioport range 0x1060-0x107f has been reserved
pnp: 00:0a: ioport range 0x1180-0x11bf has been reserved
PnPBIOS: 18 nodes reported by PnP BIOS; 18 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:02:00.1[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 11 (level, low) -> IRQ 11
Simple Boot Flag at 0x36 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 11 (level, low) -> IRQ 11
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4528 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 5
ICH2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1800-0x1807, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x1808-0x180f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK4018GAP, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB), CHS=65535/16/63, UDMA(100)
 /dev/ide/host0/bus0/target0/lun0&#58; p1 p2 < p5 >
hdc&#58; TOSHIBA DVD-ROM SD-R2212, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting.  Commit interval 5 seconds
EXT3-fs&#58; mounted filesystem with ordered data mode.
Adding 771080k swap on /dev/hda5.  Priority&#58;-1 extents&#58;1
EXT3 FS on hda1, internal journal
hdc&#58; ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA&#40;33&#41;
Uniform CD-ROM driver Revision&#58; 3.20
input&#58; PS/2 Generic Mouse on isa0060/serio4
ieee1394&#58; Initialized config rom entry `ip1394'
sbp2&#58; $Rev&#58; 1219 $ Ben Collins <bcollins@debian.org>
usbcore&#58; registered new driver usbfs
usbcore&#58; registered new driver hub
Initializing USB Mass Storage driver...
usbcore&#58; registered new driver usb-storage
USB Mass Storage support registered.
Capability LSM initialized
mice&#58; PS/2 mouse device common for all mice
ts&#58; Compaq touchscreen protocol output
Linux agpgart interface v0.100 &#40;c&#41; Dave Jones
Linux Kernel Card Services
  options&#58;  &#91;pci&#93; &#91;cardbus&#93; &#91;pm&#93;
ACPI&#58; PCI interrupt 0000&#58;02&#58;00.0&#91;A&#93; -> GSI 5 &#40;level, low&#41; -> IRQ 5
Yenta&#58; CardBus bridge found at 0000&#58;02&#58;00.0 &#91;1179&#58;ff00&#93;
Yenta&#58; ISA IRQ mask 0x0498, PCI irq 5
Socket status&#58; 30000006
ACPI&#58; PCI interrupt 0000&#58;02&#58;00.1&#91;B&#93; -> GSI 11 &#40;level, low&#41; -> IRQ 11
Yenta&#58; CardBus bridge found at 0000&#58;02&#58;00.1 &#91;1179&#58;ff00&#93;
Yenta&#58; ISA IRQ mask 0x0498, PCI irq 11
Socket status&#58; 30000410
ohci1394&#58; $Rev&#58; 1223 $ Ben Collins <bcollins@debian.org>
ACPI&#58; PCI interrupt 0000&#58;02&#58;0a.0&#91;A&#93; -> GSI 11 &#40;level, low&#41; -> IRQ 11
ohci1394&#58; fw-host0&#58; OHCI-1394 1.1 &#40;PCI&#41;&#58; IRQ=&#91;11&#93;  MMIO=&#91;e8105000-e81057ff&#93;  Max Packet=&#91;2048&#93;
e100&#58; Intel&#40;R&#41; PRO/100 Network Driver, 3.0.18
e100&#58; Copyright&#40;c&#41; 1999-2004 Intel Corporation
ACPI&#58; PCI interrupt 0000&#58;02&#58;08.0&#91;A&#93; -> GSI 11 &#40;level, low&#41; -> IRQ 11
e100&#58; eth0&#58; e100_probe&#58; addr 0xe8104000, irq 11, MAC addr 00&#58;02&#58;3F&#58;7C&#58;95&#58;D5
USB Universal Host Controller Interface driver v2.2
ACPI&#58; PCI interrupt 0000&#58;00&#58;1f.2&#91;D&#93; -> GSI 5 &#40;level, low&#41; -> IRQ 5
uhci_hcd 0000&#58;00&#58;1f.2&#58; Intel Corp. 82801BA/BAM USB &#40;Hub #1&#41;
ieee1394&#58; Host added&#58; ID&#58;BUS&#91;0-00&#58;1023&#93;  GUID&#91;00023f2a20006ceb&#93;
PCI&#58; Setting latency timer of device 0000&#58;00&#58;1f.2 to 64
uhci_hcd 0000&#58;00&#58;1f.2&#58; irq 5, io base 00001820
uhci_hcd 0000&#58;00&#58;1f.2&#58; new USB bus registered, assigned bus number 1
hub 1-0&#58;1.0&#58; USB hub found
hub 1-0&#58;1.0&#58; 2 ports detected
ACPI&#58; PCI interrupt 0000&#58;00&#58;1f.4&#91;C&#93; -> GSI 5 &#40;level, low&#41; -> IRQ 5
uhci_hcd 0000&#58;00&#58;1f.4&#58; Intel Corp. 82801BA/BAM USB &#40;Hub #2&#41;
PCI&#58; Setting latency timer of device 0000&#58;00&#58;1f.4 to 64
uhci_hcd 0000&#58;00&#58;1f.4&#58; irq 5, io base 00001840
uhci_hcd 0000&#58;00&#58;1f.4&#58; new USB bus registered, assigned bus number 2
ip1394&#58; $Rev&#58; 1224 $ Ben Collins <bcollins@debian.org>
ip1394&#58; eth1&#58; IEEE-1394 IPv4 over 1394 Ethernet &#40;fw-host0&#41;
hub 2-0&#58;1.0&#58; USB hub found
hub 2-0&#58;1.0&#58; 2 ports detected
usb 2-2&#58; new low speed USB device using address 2
usbcore&#58; registered new driver hiddev
input&#58; USB HID v1.00 Mouse &#91;Microsoft Microsoft 3-Button Mouse with IntelliEye?&#93; on usb-0000&#58;00&#58;1f.4-2
usbcore&#58; registered new driver usbhid
drivers/usb/input/hid-core.c&#58; v2.0&#58;USB HID core driver
agpgart&#58; Detected an Intel i845 Chipset.
agpgart&#58; Maximum main memory to use for agp memory&#58; 690M
agpgart&#58; AGP aperture is 64M @ 0xec000000
cpci_hotplug&#58; CompactPCI Hot Plug Core version&#58; 0.2
pci_hotplug&#58; PCI Hot Plug PCI Core version&#58; 0.5
pciehp&#58; PCI Express Hot Plug Controller Driver version&#58; 0.4
shpchp&#58; shpc_init &#58; shpc_cap_offset == 0
shpchp&#58; shpc_init &#58; shpc_cap_offset == 0
shpchp&#58; Standard Hot Plug PCI Controller Driver version&#58; 0.4
hw_random hardware driver 1.0.0 loaded
ACPI&#58; PCI interrupt 0000&#58;00&#58;1f.5&#91;B&#93; -> GSI 11 &#40;level, low&#41; -> IRQ 11
PCI&#58; Setting latency timer of device 0000&#58;00&#58;1f.5 to 64
intel8x0_measure_ac97_clock&#58; measured 50964 usecs
intel8x0&#58; clocking to 48000
ACPI&#58; PCI interrupt 0000&#58;00&#58;1f.6&#91;B&#93; -> GSI 11 &#40;level, low&#41; -> IRQ 11
PCI&#58; Setting latency timer of device 0000&#58;00&#58;1f.6 to 64
MC'97 1 converters and GPIO not ready &#40;0xf200&#41;
Real Time Clock Driver v1.12
input&#58; PC Speaker
inserting floppy driver for 2.6.8-2-686
Floppy drive&#40;s&#41;&#58; fd0 is 1.44M
FDC 0 is a post-1991 82077
parport&#58; PnPBIOS parport detected.
parport0&#58; PC-style at 0x378, irq 7 &#91;PCSPP,TRISTATE,EPP&#93;
NET&#58; Registered protocol family 17
e100&#58; eth0&#58; e100_watchdog&#58; link up, 100Mbps, full-duplex
cs&#58; IO port probe 0x0100-0x04ff&#58; excluding 0x200-0x20f
cs&#58; IO port probe 0x0800-0x08ff&#58; clean.
cs&#58; IO port probe 0x0c00-0x0cff&#58; clean.
cs&#58; IO port probe 0x0a00-0x0aff&#58; clean.
cs&#58; memory probe 0xa0000000-0xa0ffffff&#58; clean.
orinoco.c 0.13e &#40;David Gibson <hermes@gibson.dropbear.id.au> and others&#41;
orinoco_cs.c 0.13e &#40;David Gibson <hermes@gibson.dropbear.id.au> and others&#41;
eth2&#58; Station identity 001f&#58;0006&#58;0001&#58;0003
eth2&#58; Looks like an Intersil firmware version 1.3.6
eth2&#58; Ad-hoc demo mode supported
eth2&#58; IEEE standard IBSS ad-hoc mode supported
eth2&#58; WEP supported, 104-bit key
eth2&#58; MAC address 00&#58;09&#58;5B&#58;4B&#58;4E&#58;AF
eth2&#58; Station name "Prism  I"
eth2&#58; ready
eth2&#58; index 0x01&#58; Vcc 5.0, irq 3, io 0x0100-0x013f
NET&#58; Registered protocol family 10
Disabled Privacy Extensions on device c0300140&#40;lo&#41;
IPv6 over IPv4 tunneling driver
eth0&#58; no IPv6 routers present
    MCP | Network+
    Reply With Quote Reply With Quote
  3. 08-10-2005 #13
    winter
    winter is offline
    Linux User
    Join Date
    Jul 2005
    Posts
    369
    wait a minuet what card do you have?
    All i want for christmas is a new liver....a second chance to get afflicted with Cirrhosis
    Reply With Quote Reply With Quote
  4. 08-10-2005 #14
    zapper21
    zapper21 is offline
    Just Joined!
    Join Date
    Nov 2004
    Location
    Florida
    Posts
    52
    Hi, guys. Im sorry to butt in this thread but i think im having the same problem as coke can and i was hoping anyone could help me. I ran the commands you told him and this is what i get:


    linux:/home/krackz # dsmeg
    bash: dsmeg: command not found
    linux:/home/krackz # dmesg
    Linux version 2.6.11.4-21.8-default (geeko@buildhost) (gcc version 3.3.5 2005011
    7 (prerelease) (SUSE Linux)) #1 Tue Jul 19 12:42:37 UTC 2005
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000000eee0000 (usable)
    BIOS-e820: 000000000eee0000 - 000000000eeeb000 (ACPI data)
    BIOS-e820: 000000000eeeb000 - 000000000ef00000 (ACPI NVS)
    BIOS-e820: 000000000ef00000 - 0000000010000000 (reserved)
    BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
    BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
    0MB HIGHMEM available.
    238MB LOWMEM available.
    On node 0 totalpages: 61152
    DMA zone: 4096 pages, LIFO batch:1
    Normal zone: 57056 pages, LIFO batch:13
    HighMem zone: 0 pages, LIFO batch:1
    DMI 2.3 present.
    ACPI: RSDP (v000 PTLTD ) @ 0x000f6cd0
    ACPI: RSDT (v001 PTLTD Montara 0x06040000 LTP 0x00000000) @ 0x0eee5c9b
    ACPI: FADT (v001 INTEL MONTARAG 0x06040000 PTL 0x00000050) @ 0x0eeeaa2d
    ACPI: SSDT (v001 INTEL GV3Ref 0x06040000 MSFT 0x0100000e) @ 0x0eeeaaa1
    ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0eeeafd8
    ACPI: DSDT (v001 INTEL MONTARAG 0x06040000 MSFT 0x0100000e) @ 0x00000000
    ACPI: PM-Timer IO Port: 0x1008
    ACPI: local apic disabled
    Allocating PCI resources starting at 10000000 (gap: 10000000:ef800000)
    Built 1 zonelists
    Kernel command line: root=/dev/hda6 vga=0x314 selinux=0 splash=silent resume=/d
    ev/hda5
    bootsplash: silent mode.
    Initializing CPU#0
    PID hash table entries: 1024 (order: 10, 16384 bytes)
    Detected 1594.998 MHz processor.
    Using pmtmr for high-res timesource
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    Memory: 237364k/244608k available (1866k kernel code, 6640k reserved, 658k data,
    204k init, 0k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay loop... 3162.11 BogoMIPS (lpj=1581056)
    Security Framework v1.0.0 initialized
    SELinux: Disabled at boot.
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 00000180
    00000000 00000000
    CPU: After vendor identify, caps: afe9f9bf 00000000 00000000 00000000 00000180 0
    0000000 00000000
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: After all inits, caps: afe9f9bf 00000000 00000000 00000040 00000180 0000000
    0 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 06
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    checking if image is initramfs... it is
    Freeing initrd memory: 1380k freed
    ACPI: Looking for DSDT in initrd... not found!
    not found!
    ACPI: setting ELCR to 0200 (from 0c00)
    NET: Registered protocol family 16
    PCI: PCI BIOS revision 2.10 entry at 0xfd812, last bus=2
    PCI: Using configuration type 1
    mtrr: v2.0 (20020519)
    ACPI: Subsystem revision 20050211
    ACPI: Interpreter enabled
    ACPI: Using PIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (00:00)
    PCI: Probing PCI hardware (bus 00)
    PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
    PCI: Transparent bridge - 0000:00:1e.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 10 *11)
    ACPI: PCI Interrupt Link [LNKB] (IRQs *10 11)
    ACPI: PCI Interrupt Link [LNKC] (IRQs *10 11)
    ACPI: PCI Interrupt Link [LNKD] (IRQs *10 11)
    ACPI: PCI Interrupt Link [LNKE] (IRQs *10 11)
    ACPI: PCI Interrupt Link [LNKF] (IRQs *10 11)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 10 *11)
    ACPI: Embedded Controller [EC0] (gpe 2
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: PnP ACPI: found 8 devices
    PCI: Using ACPI for IRQ routing
    PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
    TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
    Simple Boot Flag at 0x36 set to 0x1
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    apm: overridden by ACPI.
    audit: initializing netlink socket (disabled)
    audit(1123631765.773:0): initialized
    Total HugeTLB memory allocated, 0
    VFS: Disk quotas dquot_6.5.1
    Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    Initializing Cryptographic API
    vesafb: framebuffer at 0xe8000000, mapped to 0xcf880000, using 3750k, total 1619
    2k
    vesafb: mode is 800x600x16, linelength=1600, pages=15
    vesafb: protected mode interface info at 00ff:44f0
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 39926 byt
    es,<6>...found (800x600, 25182 bytes, v3).
    Console: switching to colour frame buffer device 99x34
    fb0: VESA VGA frame buffer device
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    Real Time Clock Driver v1.12
    PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    serio: i8042 AUX port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
    PCI: setting IRQ 10 as level-triggered
    ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered
    floppy0: no floppy controllers found
    RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
    loop: loaded (max 8 devices)
    mice: PS/2 mouse device common for all mice
    input: PC Speaker
    md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
    NET: Registered protocol family 2
    IP: routing cache hash table of 2048 buckets, 16Kbytes
    TCP established hash table entries: 8192 (order: 4, 65536 bytes)
    TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
    TCP: Hash tables configured (established 8192 bind 8192)
    NET: Registered protocol family 1
    PM: Checking swsusp image.
    PM: Resume from disk failed.
    ACPI wakeup devices:
    LID0 SLPB LANC MODM
    ACPI: (supports S0 S3 S4 S5)
    Freeing unused kernel memory: 204k freed
    input: AT Translated Set 2 keyboard on isa0060/serio0
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH4: IDE controller at PCI slot 0000:00:1f.1
    PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
    ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 10 (level, low) -> IRQ 10
    ICH4: chipset revision 3
    ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hdaMA, hdbio
    ide1: BM-DMA at 0x1818-0x181f, BIOS settings: hdcMA, hddio
    Probing IDE interface ide0...
    hda: TOSHIBA MK6026GAX, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hdc: PHILIPS CD-RW/DVD-ROM CDD5263, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    hda: max request size: 128KiB
    hda: 117210240 sectors (60011 MB), CHS=65535/16/63, UDMA(100)
    hda: cache flushes supported
    hda: hda1 hda2 < hda5 hda6 >
    hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    Synaptics Touchpad, model: 1
    Firmware: 6.2
    180 degree mounted touchpad
    Sensor: 37
    new absolute packet format
    Touchpad has extended capability bits
    -> multifinger detection
    -> palm detection
    input: SynPS/2 Synaptics TouchPad on isa0060/serio1
    Attempting manual resume
    PM: Checking swsusp image.
    swsusp: Suspend partition has wrong signature?
    PM: Resume from disk failed.
    ReiserFS: hda6: found reiserfs format "3.6" with standard journal
    ReiserFS: hda6: using ordered data mode
    reiserfs: using flush barriers
    ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18,
    max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: hda6: checking transaction log (hda6)
    ReiserFS: hda6: Using r5 hash to sort names
    bootsplash: status on console 0 changed to on
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: ... autorun DONE.
    Adding 473876k swap on /dev/hda5. Priority:42 extents:1
    device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
    cdrom: open failed.
    NTFS driver 2.1.22 [Flags: R/W MODULE].
    NTFS volume version 3.1.
    pnp: Device 00:05 activated.
    parport: PnPBIOS parport detected.
    pnp: Device 00:05 disabled.
    lp: driver loaded but no devices found
    Capability LSM initialized
    ieee1394: Initialized config rom entry `ip1394'
    ieee1394: raw1394: /dev/raw1394 device initialized
    ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
    PCI: Enabling device 0000:02:04.2 (0000 -> 0002)
    ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
    ACPI: PCI interrupt 0000:02:04.2[C] -> GSI 10 (level, low) -> IRQ 10
    ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[e0208000-e02087ff] Max
    Packet=[2048]
    video1394: Installed video1394 module
    NET: Registered protocol family 10
    Disabled Privacy Extensions on device c033d600(lo)
    IPv6 over IPv4 tunneling driver
    ip6_tables: (C) 2000-2002 Netfilter core team
    hw_random hardware driver 1.0.0 loaded
    ieee1394: Host added: ID:BUS[0-00:1023] GUID[813f120091ed7f00]
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    USB Universal Host Controller Interface driver v2.2
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    load_module: err 0xffffffef (dont worry)
    Linux agpgart interface v0.100 (c) Dave Jones
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: irq 11, io base 0x1820
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
    ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 10 (level, low) -> IRQ 10
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: irq 10, io base 0x1840
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 10 (level, low) -> IRQ 10
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    ieee80211_crypt: module not supported by Novell, setting U taint flag.
    ieee80211_crypt: registered algorithm 'NULL'
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: irq 10, io base 0x1860
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    agpgart: Detected an Intel 855 Chipset.
    agpgart: Maximum main memory to use for agp memory: 188M
    agpgart: Detected 16252K stolen memory.
    agpgart: AGP aperture is 128M @ 0xe8000000
    ieee80211: module not supported by Novell, setting U taint flag.
    ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
    ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: irq 11, pci mem 0xe0100000
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
    PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 5 ports detected
    ip_tables: (C) 2000-2002 Netfilter core team
    ip_conntrack version 2.1 (1911 buckets, 15288 max) - 248 bytes per conntrack
    ipw2200: module not supported by Novell, setting U taint flag.
    ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.1
    ipw2200: Copyright(c) 2003-2004 Intel Corporation
    ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
    ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 10 (level, low) -> IRQ 10
    ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
    Linux Kernel Card Services
    options: [pci] [cardbus] [pm]
    usb 4-1: new high speed USB device using ehci_hcd and address 2
    bootsplash: status on console 0 changed to on
    BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
    cdrom: open failed.
    Disabled Privacy Extensions on device cdf31400(sit0)
    ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 10 (level, low) -> IRQ 10
    Yenta: CardBus bridge found at 0000:02:04.0 [1028:018d]
    Yenta: ISA IRQ mask 0x00f8, PCI irq 10
    Socket status: 30000006
    ACPI: PCI interrupt 0000:02:04.1[B] -> GSI 10 (level, low) -> IRQ 10
    Yenta: CardBus bridge found at 0000:02:04.1 [1028:018d]
    Yenta: ISA IRQ mask 0x00f8, PCI irq 10
    Socket status: 30000006
    ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10
    PCI: Setting latency timer of device 0000:00:1f.5 to 64
    intel8x0_measure_ac97_clock: measured 55196 usecs
    intel8x0: clocking to 48000
    b44.c:v0.95 (Aug 3, 2004)
    ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 10 (level, low) -> IRQ 10
    eth1: Broadcom 4400 10/100BaseT Ethernet 00:12:3f:7f:ed:91
    SCSI subsystem initialized
    st: Version 20041025, fixed bufsize 32768, s/g segs 256
    cs: IO port probe 0xc00-0xcff: clean.
    cs: IO port probe 0xc00-0xcff: clean.
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0x820-0x8ff: clean.
    cs: IO port probe 0x800-0x80f: clean.
    cs: IO port probe 0x800-0x80f: clean.
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0x100-0x3af: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    cs: IO port probe 0xa00-0xaff: clean.
    Initializing USB Mass Storage driver...
    scsi0 : SCSI emulation for USB Mass Storage devices
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    usb-storage: device found at 2
    usb-storage: waiting for device to settle before scanning
    ieee80211_crypt_wep: module not supported by Novell, setting U taint flag.
    ieee80211_crypt: registered algorithm 'WEP'
    NET: Registered protocol family 17
    Vendor: M-SysT5 Model: Dell Memory Key Rev: 5.00
    Type: Direct-Access ANSI SCSI revision: 00
    sda: Unit Not Ready, sense:
    : Current: sense key: Unit Attention
    Additional sense: Not ready to ready change, medium may have changed
    SCSI device sda: 123903 512-byte hdwr sectors (63 MB)
    sda: Write Protect is off
    sda: Mode Sense: 45 00 00 08
    sda: assuming drive cache: write through
    SCSI device sda: 123903 512-byte hdwr sectors (63 MB)
    sda: Write Protect is off
    sda: Mode Sense: 45 00 00 08
    sda: assuming drive cache: write through
    sda: sda1
    Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
    Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
    usb-storage: device scan complete
    [drm] Initialized drm 1.0.0 20040925
    ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
    mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x800000
    [drm] Initialized i915 1.1.0 20040405 on minor 0:
    mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x800000
    [drm] Initialized i915 1.1.0 20040405 on minor 1:
    mtrr: base(0xe8020000) is not aligned on a size(0x300000) boundary
    mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x800000
    b44: eth1: Link is down.
    eth0: no IPv6 routers present
    eth1: no IPv6 routers present
    Non-volatile memory driver v1.2
    ACPI: AC Adapter [ADP1] (on-line)
    ACPI: Battery Slot [BAT0] (battery present)
    ACPI: Power Button (FF) [PWRF]
    ACPI: Lid Switch [LID0]
    ACPI: Sleep Button (CM) [SLPB]
    ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
    ACPI: Processor [CPU0] (supports 8 throttling states)
    ACPI: Thermal Zone [THRC] (57 C)
    ACPI: Thermal Zone [THRS] (48 C)
    bootsplash: status on console 0 changed to on
    bootsplash: status on console 0 changed to on
    drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
    usbcore: registered new driver usbserial_generic
    usbcore: registered new driver usbserial
    drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
    subfs 0.9
    ACPI-1041: *** Warning: Failed to acquire semaphore[ceec8d60|1|0], AE_TIME
    linux:/home/krackz #


    ################################################## ################################################## ###############################

    lspci
    0000:00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
    0000:00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
    0000:00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
    0000:00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
    0000:00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
    0000:00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
    0000:00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
    0000:00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03)
    0000:00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
    0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
    0000:00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
    0000:00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
    0000:00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
    0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
    0000:00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03)
    0000:02:01.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
    0000:02:04.0 CardBus bridge: Texas Instruments PCI7420 CardBus Controller
    0000:02:04.1 CardBus bridge: Texas Instruments PCI7420 CardBus Controller
    0000:02:04.2 FireWire (IEEE 1394): Texas Instruments PCI7x20 1394a-2000 OHCI Two-Port PHY/Link-Layer Controller
    0000:02:04.3 Unknown mass storage controller: Texas Instruments PCI7420/PCI7620 Dual Socket CardBus and Smart Card Cont. w/ 1394a-2000 OHCI Two-Port PHY/Link-Layer Cont. an
    0000:02:05.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
    ################################################## ################################################## #######################################
    linux:/home/krackz # iwconfig
    lo no wireless extensions.

    sit0 no wireless extensions.

    eth0 IEEE 802.11g ESSID:"NETGEAR" Nickname:"linux"
    Mode:Managed Frequency:2.462 GHz Access Point: 00:09:5B:53:B1:A4
    Bit Rate=54 Mb/s Tx-Power=20 dBm
    RTS thr:off Fragment thr:off
    Encryption key:3041-FD0D-FCBD-7452-FF01-3744-23 Security mode:open
    Power Management:off
    Link Quality=91/100 Signal level=-37 dBm Noise level=-81 dBm
    Rx invalid nwid:0 Rx invalid crypt:3 Rx invalid frag:0
    Tx excessive retries:0 Invalid misc:0 Missed beacon:3

    eth1 no wireless extensions.

    linux:/home/krackz #

    i ran ifup eth0 and it said that dhcp client was running on the machine,
    and the other command

    I guess those negative values for the noise level and signal level have something to do with it?
    by the way im using an intel prowireless 2200GB card.
    Thanks in advance!!!
    Reply With Quote Reply With Quote
  5. 08-10-2005 #15
    COKE CAN
    COKE CAN is offline
    Linux Newbie
    Join Date
    Jun 2005
    Location
    Yorktown, VA
    Posts
    215
    Quote Originally Posted by winter
    wait a minuet what card do you have?
    Netgear MA401 802.11b
    MCP | Network+
    Reply With Quote Reply With Quote
  6. 08-10-2005 #16
    loft306
    loft306 is offline
    Linux Guru loft306's Avatar
    Join Date
    Oct 2003
    Location
    The DairyLand
    Posts
    1,666
    what is the output of
    Code:
    ifconfig
    you also need to start the nic in the same way as you start ethernet nic's by bringing it up
    ~Mike ~~~ Forum Rules
    Testing? What's that? If it compiles, it is good, if it boots up, it is perfect. ~ Linus Torvalds
    http://loft306.org
    Reply With Quote Reply With Quote
  7. 08-11-2005 #17
    zapper21
    zapper21 is offline
    Just Joined!
    Join Date
    Nov 2004
    Location
    Florida
    Posts
    52
    I dont know if you meant Coke can or Me but here goes my output for ifconfig:

    linux:/home/krackz # ifconfig
    eth0 Link encap:Ethernet HWaddr 00:12:3F:7F:ED:91
    inet6 addr: fe80::212:3fff:fe7f:ed91/64 Scope:Link
    UP BROADCAST NOTRAILERS MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:4642 (4.5 Kb)
    Interrupt:10

    eth1 Link encap:Ethernet HWaddr 00:12:F0:7F:BF:15
    inet6 addr: fe80::212:f0ff:fe7f:bf15/64 Scope:Link
    UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:27 errors:7 dropped:7 overruns:0 frame:0
    TX packets:11 errors:0 dropped:0 overruns:0 carrier:2
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:3848 (3.7 Kb)
    Interrupt:10 Base address:0xe000 Memory:e0206000-e0206fff

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:96 errors:0 dropped:0 overruns:0 frame:0
    TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:6768 (6.6 Kb) TX bytes:6768 (6.6 Kb)
    Reply With Quote Reply With Quote
  8. 08-11-2005 #18
    COKE CAN
    COKE CAN is offline
    Linux Newbie
    Join Date
    Jun 2005
    Location
    Yorktown, VA
    Posts
    215
    I got mad and decided to try Gentoo on my laptop. Now that I couldn't get that (the operating system) to work, I'm trying Slackware. If that doesn't work, I'll try Debian again, and start fresh.
    MCP | Network+
    Reply With Quote Reply With Quote
  9. 08-11-2005 #19
    zapper21
    zapper21 is offline
    Just Joined!
    Join Date
    Nov 2004
    Location
    Florida
    Posts
    52
    I beg the linux community to please help me get my wireless card working. I've been trying to get it to work since forever with suse 9.2- 3 gentoo 2005, knoppinx-whoppix-slackware and a couple of more distros and havent been succesful. Not getting my card wireless card to work on linux is the only reason I still have windows(I really want to get rid of windows)Please help me on this one? thanks
    Reply With Quote Reply With Quote
  10. 08-11-2005 #20
    zapper21
    zapper21 is offline
    Just Joined!
    Join Date
    Nov 2004
    Location
    Florida
    Posts
    52
    Well thanks guys i finally fixed my wireless card, looked at www.linuxquestions.org and found out how to fix it. But thanks anyways to the members of this forums. Coke Can in case you're interested, you should take a look at that website you might be able to find a solution to your problem or they might help you.
    thnx everyone (goodbye windows)
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 1 2
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

...