eth0 problem /Reaktek RTL8139/

[TrashOverride]

Hi all willing to help
I have Realtek RTL8139 Family PCI. I'm using Slackware 9.1
and i'm havig problem connecting to the internet through my lan card

eth0 Link encap:Ethernet HWaddr 00:50:FC:F9:9B:48
inet addr:172.16.*.* Bcast:172.16.255.255 Mask:255.255.*.*
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:63119 errors:0 dropped:0 overruns:0 frame:0
TX packets:398 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4283287 (4.0 Mb) TX bytes:43565 (42.5 Kb)
Interrupt:16

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

when booting it says
eth0: link up, 100Mb....
so i think i have the card runnig but i cannot open any web page
i've done the ifconfig

and it seem there is no /etc/sysconfig/network-scripts/ifcfg-eth0... or i dont see it

can u help?

[ooop]

Firstly of all...

can you ping anything (your default gateway would be a good choice)
because if you can, then the device is at least working.

to visit webpages you need to configure resolv.conf

this is easily done, just add

nameserver 1.2.3.4

where 1.2.3.4 is the IP to your DNS-server...

if you can't ping anything, then the problem is probably the device though

/ooop

[TrashOverride]

here is my lspci

00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge
00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50)
01:00.0 VGA compatible controller: nVidia Corporation NV28 [GeForce4 Ti 4200 AGP 8x] (rev a1)

so its obiosly working. I'll try the ping and the resolf.conf. 10x

[TrashOverride]

Eurika! it worked but when i try to brouse lan "lan:/"
Error msg:

The lisa daemon does not appear to be running.
In order to use the LAN Browser the lisa daemon must be installed and activated by the system administrator.

the thing is that i am the sys admin and i configured lisa

[jeremy1701]

Not to be a punk, but is the deamon running?

Jeremy

[TrashOverride]

oooops!
10x for reminding to run it