Find the answer to your Linux question:
Results 1 to 4 of 4
Hello, I am trying to use CentOS 4.6 to build web server at home (LAMP stack). As far as I can tell its working properly, it boots at least and ...
Enjoy an ad free experience by logging in. Not a member yet? Register.
  1. #1
    Just Joined!
    Join Date
    Sep 2008
    Posts
    2

    Unhappy CentOS 4.6 Network Card Issue


    Hello,

    I am trying to use CentOS 4.6 to build web server at home (LAMP stack). As far as I can tell its working properly, it boots at least and i can run some root commands.

    From what i have seen in various installs i need to "yum" something to get an update of some sort, however I can't get the network card to actually access the internet.

    My network card is as follows:
    Accton Tech SMC2-1211TX (rev 10)

    when i do a: "dmesg | more" one of the last lines i get is
    eth0: no IPv6 routers present

    as far as i can remember i have my network set up this way (on the system)
    IP 192.168.0.100
    gateway: 255.255.255.0
    im not sure if i need to change my dns settings on the machine (which i dont remember how i did in the first place) or whatnot.


    i can give more details but i dont know the commands to show them.

    any help on this would be great.

  2. #2
    Linux Guru Lazydog's Avatar
    Join Date
    Jun 2004
    Location
    The Keystone State
    Posts
    2,677
    What are the output of the following commands:

    route -n
    ifconfig
    cat /etc/resolv.conf

    Regards
    Robert

    Linux
    The adventure of a life time.

    Linux User #296285
    Get Counted

  3. #3
    Just Joined!
    Join Date
    Sep 2008
    Posts
    2
    Hi Lazydog

    below is what im getting:

    route:
    Kernel IP routing table:
    Destination Gateway GenMask Flags Metric Ref Use Iface
    192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
    169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth 0
    0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth 0

    ifconfig
    eth0
    Link encap: Ethernet HWaddr 00:10:B5:7D:0FD
    inet addr: 192.168.0.100 Bcast: 192.168.0.255 Mask 255.255.255.0
    UP BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    Interrupt:10 Base address:0x2800

    lo
    Link encap:Local Loopback
    inet addr: 127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:8 errors:0 dropped:0 overruns:0 frame:0
    TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)

    cat /etc/resolv.conf
    search localdomain

    hope this makes sense

    thanks

    eric

  4. $spacer_open
    $spacer_close
  5. #4
    Linux Guru Lazydog's Avatar
    Join Date
    Jun 2004
    Location
    The Keystone State
    Posts
    2,677
    You don't have any DNS servers in your resolv.conf file.
    Add your ISP's DNS server there.

    Regards
    Robert

    Linux
    The adventure of a life time.

    Linux User #296285
    Get Counted

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •