Find the answer to your Linux question:
Results 1 to 2 of 2
I have just installed Fedora 6 onto a SCSI driive. I am trying to access a RAID0 on the same computer. The RAID is using the intel 875P chip on ...
Enjoy an ad free experience by logging in. Not a member yet? Register.
  1. #1
    Just Joined!
    Join Date
    Oct 2006
    Posts
    24

    Help trying so mount RAID0


    I have just installed Fedora 6 onto a SCSI driive. I am trying to access a RAID0 on the same computer. The RAID is using the intel 875P chip on a Asus P4C800-E deluxe mobo. It is also ntfs. I have installed the ntfs drivers but dont know how the mount the RAID.

    Its the letter ID I need that references the RAID. If primary IDE is hda1 (secondary hda2 and so on) and first SCSI is sda1 (second SCSI sda2 and so on). What would RAID0 be? I did dmesg and I can see both drives which make up the RAID0 but the ID only shows each individual drive not the RAID. I have put most of the dmesg output here. You can see that the two drives which make up the RAID get listed twice as ata1 and ata2 and then again as sdb and sdc. Also further down you can see "autodedcting RAID arrays" comes up so I must just need the letter that fedora uses. What other commands would show the RAID0.

    Code:
    Linux agpgart interface v0.101 (c) Dave Jones
    agpgart: Detected an Intel i875 Chipset.
    agpgart: AGP aperture is 128M @ 0xf0000000
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH5: IDE controller at PCI slot 0000:00:1f.1
    PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
    ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
    ICH5: chipset revision 2
    ICH5: not 100% native mode: will probe irqs later
        ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
        ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
    Probing IDE interface ide0...
    hda: Maxtor 6Y120P0, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hdc: PLEXTOR DVDR PX-708A, ATAPI CD/DVD-ROM drive
    hdd: PLEXTOR CD-R PREMIUM, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    hda: max request size: 128KiB
    hda: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(100)
    hda: cache flushes supported
     hda: hda1
    
    scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
            <Adaptec 29160N Ultra160 SCSI adapter>
            aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
    
      Vendor: MATSHITA  Model: DVD-RAM LF-D200   Rev: X120
      Type:   CD-ROM                             ANSI SCSI revision: 04
     target0:0:4: Beginning Domain Validation
     target0:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 32)
     target0:0:4: Domain Validation skipping write tests
     target0:0:4: Ending Domain Validation
      Vendor: IBM       Model: IC35L036UWD210-0  Rev: S5CQ
      Type:   Direct-Access                      ANSI SCSI revision: 03
    scsi0:A:6:0: Tagged Queuing enabled.  Depth 4
     target0:0:6: Beginning Domain Validation
     target0:0:6: wide asynchronous
     target0:0:6: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
     target0:0:6: Ending Domain Validation
    SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
    sda: Write Protect is off
    sda: Mode Sense: cb 00 00 08
    SCSI device sda: drive cache: write back
    SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
    sda: Write Protect is off
    sda: Mode Sense: cb 00 00 08
    SCSI device sda: drive cache: write back
     sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
    sd 0:0:6:0: Attached scsi disk sda
    libata version 2.00 loaded.
    ata_piix 0000:00:1f.2: version 2.00
    ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
    ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF90 irq 169
    ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF98 irq 169
    scsi1 : ata_piix
    ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 
    ata1.00: ata1: dev 0 multi count 16
    ata1.00: configured for UDMA/133
    scsi2 : ata_piix
    ata2.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48 
    ata2.00: ata2: dev 0 multi count 16
    ata2.00: configured for UDMA/133
      Vendor: ATA       Model: Maxtor 7Y250M0    Rev: YAR5
      Type:   Direct-Access                      ANSI SCSI revision: 05
    SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
    sdb: Write Protect is off
    sdb: Mode Sense: 00 3a 00 00
    SCSI device sdb: drive cache: write back
    SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
    sdb: Write Protect is off
    sdb: Mode Sense: 00 3a 00 00
    SCSI device sdb: drive cache: write back
     sdb: sdb1 sdb2 < >
    sd 1:0:0:0: Attached scsi disk sdb
      Vendor: ATA       Model: Maxtor 7Y250M0    Rev: YAR5
      Type:   Direct-Access                      ANSI SCSI revision: 05
    SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
    sdc: Write Protect is off
    sdc: Mode Sense: 00 3a 00 00
    SCSI device sdc: drive cache: write back
    SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
    sdc: Write Protect is off
    sdc: Mode Sense: 00 3a 00 00
    SCSI device sdc: drive cache: write back
     sdc: unknown partition table
    sd 2:0:0:0: Attached scsi disk sdc
    device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
    kjournald starting.  Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    audit(1167496402.383:2): enforcing=1 old_enforcing=0 auid=4294967295
    security:  3 users, 6 roles, 1583 types, 172 bools, 1 sens, 1024 cats
    security:  59 classes, 49428 rules
    
    audit(1167496402.554:3): policy loaded auid=4294967295
    Initializing USB Mass Storage driver...
    scsi3 : SCSI emulation for USB Mass Storage devices
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    usb-storage: device found at 4
    usb-storage: waiting for device to settle before scanning
    hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA
    Uniform CD-ROM driver Revision: 3.20
    hdd: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, DMA
    ieee1394: Initialized config rom entry `ip1394'
    Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI
    Copyright (c) 1999-2006 Intel Corporation.
    ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 169
    PCI: Setting latency timer of device 0000:02:01.0 to 64
    e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:a6:5a:96:bf
    intel_rng: FWH not detected
    EDAC MC: Ver: 2.0.1 Dec 15 2006
    input: PC Speaker as /class/input/input4
    e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
    ACPI: PCI Interrupt 0000:03:0a.2[B] -> GSI 23 (level, low) -> IRQ 193
    ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[193]  MMIO=[feafe800-feafefff]  Max Packet=[2048]  IR/IT contexts=[4/8]
    gameport: EMU10K1 is pci0000:03:0a.1/gameport0, io 0xdfe0, speed 1169kHz
    ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 209
    scsi 0:0:4:0: Attached scsi generic sg0 type 5
    sd 0:0:6:0: Attached scsi generic sg1 type 0
    sd 1:0:0:0: Attached scsi generic sg2 type 0
    sd 2:0:0:0: Attached scsi generic sg3 type 0
    EDAC i82875p: i82875p init one
    EDAC MC0: Giving out device to i82875p_edac i82875p: DEV 0000:00:00.0
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    sr0: scsi3-mmc drive: 0x/0x dvd-ram cd/rw xa/form2 cdda tray
    sr 0:0:4:0: Attached scsi CD-ROM sr0
    ACPI: PCI Interrupt 0000:03:0a.0[A] -> GSI 22 (level, low) -> IRQ 217
    ieee1394: Host added: ID:BUS[0-01:1023]  GUID[00023c0020000c45]
    parport: PnPBIOS parport detected.
    parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
    lp0: using parport0 (interrupt-driven).
    lp0: console ready
      Vendor:           Model: USB Flash Memory  Rev: 1.04
      Type:   Direct-Access                      ANSI SCSI revision: 00
    SCSI device sdd: 1001472 512-byte hdwr sectors (513 MB)
    sdd: Write Protect is off
    sdd: Mode Sense: 23 00 00 00
    sdd: assuming drive cache: write through
    SCSI device sdd: 1001472 512-byte hdwr sectors (513 MB)
    sdd: Write Protect is off
    sdd: Mode Sense: 23 00 00 00
    sdd: assuming drive cache: write through
     sdd: sdd1
    sd 3:0:0:0: Attached scsi removable disk sdd
    sd 3:0:0:0: Attached scsi generic sg4 type 0
    usb-storage: device scan complete
    SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
    NET: Registered protocol family 10
    lo: Disabled Privacy Extensions
    IPv6 over IPv4 tunneling driver
    ACPI: Power Button (FF) [PWRF]
    ACPI: Power Button (CM) [PWRB]
    ibm_acpi: ec object not found
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: ... autorun DONE.
    device-mapper: multipath: version 1.0.4 loaded
    EXT3 FS on dm-5, internal journal
    kjournald starting.  Commit interval 5 seconds
    EXT3 FS on sda5, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    SELinux: initialized (dev sda5, type ext3), uses xattr
    SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
    Adding 2031608k swap on /dev/VolGroup00/LogVol01.  Priority:-1 extents:1 across:2031608k
    SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
    SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
    SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
    SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
    eth0: no IPv6 routers present
    SELinux: initialized (dev sdd1, type vfat), uses genfs_contexts
    NTFS driver 2.1.27 [Flags: R/W MODULE].
    NTFS-fs error (device hda1): parse_options(): Unrecognized mount option unmask.
    NTFS volume version 3.1.
    SELinux: initialized (dev hda1, type ntfs), uses genfs_contexts
    NTFS volume version 3.1.
    SELinux: initialized (dev hda1, type ntfs), uses genfs_contexts

  2. #2
    Just Joined!
    Join Date
    Oct 2006
    Posts
    24
    Here is the relevednt output from lspci -vv

    00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
    Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 169
    Region 0: I/O ports at <unassigned>
    Region 1: I/O ports at <unassigned>
    Region 2: I/O ports at <unassigned>
    Region 3: I/O ports at <unassigned>
    Region 4: I/O ports at fc00 [size=16]
    Region 5: Memory at 50000000 (32-bit, non-prefetchable) [size=1K]

    00:1f.2 RAID bus controller: Intel Corporation 82801ER (ICH5R) SATA Controller (rev 02) (prog-if 8f)
    Subsystem: ASUSTeK Computer Inc. Unknown device 80a6
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Interrupt: pin A routed to IRQ 169
    Region 0: I/O ports at efe0 [size=8]
    Region 1: I/O ports at efac [size=4]
    Region 2: I/O ports at efa0 [size=8]
    Region 3: I/O ports at efa8 [size=4]
    Region 4: I/O ports at ef90 [size=16]

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •