Find the answer to your Linux question:
Results 1 to 9 of 9
Enjoy an ad free experience by logging in. Not a member yet? Register.
  1. #1

    Cool HELP:!!!! w/ wireless in kubuntu V7.10


    I am try to get my PCI WIRELESS CARD to work in linux for kubuntv version 7.10 and it seem that it does not see my card and when I enter the info for my router on my computer the computer locks-up I can't do anythink it is an HP computer 510n

    wireless card is a TRENDnet card

    and the wireless card works find in windows XP HOME SP 1-3

    and I can't use wine right now until I can get my wireless card working because the router is too far away from the computer to use an cable for it and all the port on my router is being used I have a 4port wireless router

    I have two routers one is a 2wire DLS montom and router in one and then their is the linksyswrt53gc router

    and also my computer has 512MB( 256MB X2) RAM 1.2 GHz intel celeron processsor!





    Code:
    the following is the output code or commands
    
    
    INFO HIDEN:~$ lspci –nn
    
    lspci: invalid option -- -
    Usage: lspci [<switches>]
    
    -v              Be verbose
    -n              Show numeric ID's
    -nn             Show both textual and numeric ID's (names & numbers)
    -b              Bus-centric view (PCI addresses and IRQ's instead of those seen by the CPU)
    -x              Show hex-dump of the standard portion of config space
    -xxx            Show hex-dump of the whole config space (dangerous; root only)
    -xxxx           Show hex-dump of the 4096-byte extended config space (root only)
    -s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]]   Show only devices in selected slots
    -d [<vendor>]:[<device>]        Show only selected devices
    -t              Show bus tree
    -m              Produce machine-readable output
    -i <file>       Use specified ID database instead of /usr/share/misc/pci.ids.gz
    -D              Always show domain numbers
    -M              Enable `bus mapping' mode (dangerous; root only)
    -P <dir>        Use specified directory instead of /proc/bus/pci
    -H <mode>       Use direct hardware access (<mode> = 1 or 2)
    -F <file>       Read configuration data from given file
    -G              Enable PCI access debugging
    
    INFO HIDENn:~$ lsmod
    
    Module                  Size  Used by
    rfcomm                 42136  2
    l2cap                  26240  11 rfcomm
    bluetooth              57060  4 rfcomm,l2cap
    ppdev                  10244  0
    cpufreq_userspace       5280  0
    cpufreq_stats           7232  0
    cpufreq_powersave       2688  0
    cpufreq_conservative     8072  0
    cpufreq_ondemand        9612  0
    freq_table              5792  2 cpufreq_stats,cpufreq_ondemand
    button                  8976  0
    container               5504  0
    ac                      6148  0
    dock                   10656  0
    sbs                    19592  0
    video                  18060  0
    battery                11012  0
    sbp2                   24072  0
    lp                     12580  0
    joydev                 11328  0
    snd_intel8x0           34972  1
    snd_ac97_codec        100644  1 snd_intel8x0
    ac97_bus                3200  1 snd_ac97_codec
    snd_pcm_oss            44672  0
    snd_mixer_oss          17664  1 snd_pcm_oss
    snd_pcm                80388  3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
    snd_seq_dummy           4740  0
    parport_pc             37412  1
    snd_mpu401              9640  0
    parport                37448  3 ppdev,lp,parport_pc
    r8180                  89868  0
    snd_seq_oss            33152  0
    snd_mpu401_uart         9600  1 snd_mpu401
    ieee80211_rtl          80648  1 r8180
    analog                 13344  0
    gameport               16776  1 analog
    snd_seq_midi            9600  0
    snd_rawmidi            25728  2 snd_mpu401_uart,snd_seq_midi
    snd_seq_midi_event      8448  2 snd_seq_oss,snd_seq_midi
    xpad                    9988  0
    usbhid                 29536  1
    hid                    28928  1 usbhid
    snd_seq                53232  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
    pcspkr                  4224  0
    snd_timer              24324  2 snd_pcm,snd_seq
    snd_seq_device          9228  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
    snd                    54660  14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401,snd_seq_oss,snd_mpu401_uart,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
    soundcore               8800  1 snd
    
    snd_page_alloc         11400  2 snd_intel8x0,snd_pcm
    serio_raw               8068  0
    psmouse                39952  0
    i2c_i810                5892  0
    shpchp                 34580  0
    pci_hotplug            32704  1 shpchp
    i2c_algo_bit            7428  1 i2c_i810
    iTCO_wdt               11940  0
    iTCO_vendor_support     4868  1 iTCO_wdt
    intel_agp              25620  1
    agpgart                35016  2 intel_agp
    i2c_core               26112  2 i2c_i810,i2c_algo_bit
    evdev                  11136  5
    ext3                  133896  1
    jbd                    60456  1 ext3
    mbcache                 9732  1 ext3
    8139cp                 25088  0
    sg                     36764  0
    sr_mod                 17828  0
    cdrom                  37536  1 sr_mod
    sd_mod                 30336  3
    ata_generic             8452  0
    floppy                 60004  0
    ohci1394               36528  0
    ieee1394               96312  2 sbp2,ohci1394
    ehci_hcd               36492  0
    8139too                27776  0
    mii                     6528  2 8139cp,8139too
    uhci_hcd               26640  0
    usbcore               138632  6 xpad,usbhid,ehci_hcd,uhci_hcd
    ata_piix               17540  2
    libata                125168  2 ata_generic,ata_piix
    scsi_mod              147084  5 sbp2,sg,sr_mod,sd_mod,libata
    thermal                14344  0
    processor              32072  1 thermal
    fan                     5764  0
    fuse                   47124  1
    apparmor               40728  0
    commoncap               8320  1 apparmor
    
    
    
    INFO HIDEN:~$ dmesg
    
    [    0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
    [    0.000000] BIOS-provided physical RAM map:
    [    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    [    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    [    0.000000]  BIOS-e820: 00000000000c8000 - 00000000000d0000 (reserved)
    [    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    [    0.000000]  BIOS-e820: 0000000000100000 - 000000001fcf0000 (usable)
    [    0.000000]  BIOS-e820: 000000001fcf0000 - 000000001fcfc000 (ACPI data)
    [    0.000000]  BIOS-e820: 000000001fcfc000 - 000000001fd00000 (ACPI NVS)
    [    0.000000]  BIOS-e820: 000000001fd00000 - 000000001fe80000 (usable)
    [    0.000000]  BIOS-e820: 000000001fe80000 - 0000000020000000 (reserved)
    [    0.000000]  BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
    [    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
    [    0.000000] 0MB HIGHMEM available.
    [    0.000000] 510MB LOWMEM available.
    [    0.000000] Entering add_active_range(0, 0, 130688) 0 entries of 256 used
    [    0.000000] Zone PFN ranges:
    [    0.000000]   DMA             0 ->     4096
    [    0.000000]   Normal       4096 ->   130688
    [    0.000000]   HighMem    130688 ->   130688
    [    0.000000] early_node_map[1] active PFN ranges
    [    0.000000]     0:        0 ->   130688
    [    0.000000] On node 0 totalpages: 130688
    [    0.000000]   DMA zone: 32 pages used for memmap
    [    0.000000]   DMA zone: 0 pages reserved
    [    0.000000]   DMA zone: 4064 pages, LIFO batch:0
    [    0.000000]   Normal zone: 989 pages used for memmap
    [    0.000000]   Normal zone: 125603 pages, LIFO batch:31
    [    0.000000]   HighMem zone: 0 pages used for memmap
    [    0.000000] DMI 2.3 present.
    [    0.000000] ACPI: RSDP signature @ 0xC00F6670 checksum 0
    [    0.000000] ACPI: RSDP 000F6670, 0014 (r0 PTLTD )
    [    0.000000] ACPI: RSDT 1FCF7082, 0030 (r1 PTLTD    RSDT    6040000  LTP        0)
    [    0.000000] ACPI: FACP 1FCFBF0A, 0074 (r1 INTEL  Whitney   6040000 PTL     F4240)
    [    0.000000] ACPI: DSDT 1FCF70B2, 4E58 (r1  INTEL  Whitney  6040000 MSFT  100000D)
    [    0.000000] ACPI: FACS 1FCFCFC0, 0040
    [    0.000000] ACPI: APIC 1FCFBF7E, 005A (r1 PTLTD       APIC    6040000  LTP        0)
    [    0.000000] ACPI: BOOT 1FCFBFD8, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
    [    0.000000] ACPI: PM-Timer IO Port: 0x1008
    [    0.000000] ACPI: Local APIC address 0xfee00000
    [    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [    0.000000] Processor #0 6:11 APIC version 17
    [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    [    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [    0.000000] ACPI: IRQ0 used by override.
    [    0.000000] ACPI: IRQ2 used by override.
    [    0.000000] ACPI: IRQ9 used by override.
    [    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
    [    0.000000] Using ACPI (MADT) for SMP configuration information
    [    0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dfb80000)
    [    0.000000] Built 1 zonelists.  Total pages: 129667
    [    0.000000] Kernel command line: root=UUID=61717d39-116a-4b44-8444-baa9cf029ebe ro quiet splash
    [    0.000000] mapped APIC to ffffd000 (fee00000)
    [    0.000000] mapped IOAPIC to ffffc000 (fec00000)
    [    0.000000] Enabling fast FPU save and restore... done.
    [    0.000000] Enabling unmasked SIMD FPU exception support... done.
    [    0.000000] Initializing CPU#0
    [    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
    [    0.000000] Detected 1196.038 MHz processor.
    [   18.835019] Console: colour VGA+ 80x25
    [   18.836564] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    [   18.838080] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    [   18.894408] Memory: 506380k/522752k available (2015k kernel code, 15732k reserved, 916k data, 364k init, 0k highmem)
    [   18.894429] virtual kernel memory layout:
    [   18.894431]     fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
    [   18.894434]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    [   18.894436]     vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
    [   18.894439]     lowmem  : 0xc0000000 - 0xdfe80000   ( 510 MB)
    [   18.894441]       .init : 0xc03e3000 - 0xc043e000   ( 364 kB)
    [   18.894444]       .data : 0xc02f7d26 - 0xc03dce84   ( 916 kB)
    [   18.894446]       .text : 0xc0100000 - 0xc02f7d26   (2015 kB)
    [   18.894453] Checking if this processor honours the WP bit even in supervisor mode... Ok.
    [   18.894531] SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
    [   18.974548] Calibrating delay using timer specific routine.. 2393.98 BogoMIPS (lpj=4787973)
    [   18.974607] Security Framework v1.0.0 initialized
    [   18.974625] SELinux:  Disabled at boot.
    [   18.974658] Mount-cache hash table entries: 512
    [   18.974948] CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 00000000 00000000 00000000
    [   18.974969] CPU: L1 I cache: 16K, L1 D cache: 16K
    [   18.974974] CPU: L2 cache: 256K
    [   18.974982] CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000
    [   18.975002] Compat vDSO mapped to ffffe000.
    [   18.975031] Checking 'hlt' instruction... OK.
    [   18.990776] SMP alternatives: switching to UP code
    [   18.991161] Freeing SMP alternatives: 11k freed
    [   18.991796] Early unpacking initramfs... done
    [   19.660070] ACPI: Core revision 20070126
    [   19.660378] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
    [   19.757396] CPU0: Intel(R) Celeron(TM) CPU                1200MHz stepping 01
    [   19.757455] Total of 1 processors activated (2393.98 BogoMIPS).
    [   19.757616] ENABLING IO-APIC IRQs
    [   19.757860] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
    [   19.902547] Brought up 1 CPUs
    [   19.902863] Booting paravirtualized kernel on bare hardware
    [   19.902984] Time: 17:39:37  Date: 00/03/109
    [   19.903064] NET: Registered protocol family 16
    [   19.903383] EISA bus registered
    [   19.903410] ACPI: bus type pci registered
    [   19.904360] PCI: PCI BIOS revision 2.10 entry at 0xfd9a8, last bus=1
    [   19.904365] PCI: Using configuration type 1
    [   19.904369] Setting up standard PCI resources
    [   19.907222] ACPI: EC: Look up EC in DSDT
    [   19.913089] ACPI: Interpreter enabled
    [   19.913102] ACPI: (supports S0 S1 S3 S4 S5)
    [   19.913130] ACPI: Using IOAPIC for interrupt routing
    [   19.918910] ACPI: PCI Root Bridge [PCI0] (0000:00)
    [   19.918939] PCI: Probing PCI hardware (bus 00)
    [   19.919254] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
    [   19.919261] PCI quirk: region 1180-11bf claimed by ICH4 GPIO
    [   19.920083] PCI: Transparent bridge - 0000:00:1e.0
    [   19.920124] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [   19.920533] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
    [   19.923255] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
    [   19.923398] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12 14 15)
    [   19.923528] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
    [   19.923658] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
    [   19.923922] ACPI: Power Resource [FN01] (on)
    [   19.923937] Linux Plug and Play Support v0.97 (c) Adam Belay
    [   19.923966] pnp: PnP ACPI init
    [   19.923995] ACPI: bus type pnp registered
    [   19.957429] pnp: PnP ACPI: found 13 devices
    [   19.957438] ACPI: ACPI bus type pnp unregistered
    [   19.957450] PnPBIOS: Disabled by ACPI PNP
    [   19.957588] PCI: Using ACPI for IRQ routing
    [   19.957594] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
    [   19.961859] NET: Registered protocol family 8
    [   19.961864] NET: Registered protocol family 20
    [   19.962061] pnp: 00:01: iomem range 0xff800000-0xffffffff could not be reserved
    [   19.962068] pnp: 00:01: iomem range 0xfec00000-0xfec00fff has been reserved
    [   19.962075] pnp: 00:01: iomem range 0xfee00000-0xfee00fff has been reserved
    [   19.962088] pnp: 00:02: iomem range 0x0-0x9ffff could not be reserved
    [   19.962094] pnp: 00:02: iomem range 0xe0000-0xfffff could not be reserved
    [   19.962099] pnp: 00:02: iomem range 0x100000-0x1fffffff could not be reserved
    [   19.962434] Time: tsc clocksource has been installed.
    [   19.992812] PCI: Bridge: 0000:00:1e.0
    [   19.992818]   IO window: 2000-2fff
    [   19.992828]   MEM window: f4100000-f41fffff
    [   19.992834]   PREFETCH window: disabled.
    [   19.992854] PCI: Setting latency timer of device 0000:00:1e.0 to 64
    [   19.992884] NET: Registered protocol family 2
    [   20.030536] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    [   20.030683] TCP established hash table entries: 16384 (order: 5, 196608 bytes)
    [   20.031542] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    [   20.032384] TCP: Hash tables configured (established 16384 bind 16384)
    [   20.032394] TCP reno registered
    [   20.042845] checking if image is initramfs...<6>Switched to high resolution mode on CPU 0
    [   20.542761]  it is
    [   21.259587] Freeing initrd memory: 7361k freed
    [   21.260022] Simple Boot Flag at 0x35 set to 0x1
    [   21.260822] audit: initializing netlink socket (disabled)
    [   21.260859] audit(1231004377.876:1): initialized
    [   21.265661] VFS: Disk quotas dquot_6.5.1
    [   21.265865] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [   21.266241] io scheduler noop registered
    [   21.266249] io scheduler anticipatory registered
    [   21.266253] io scheduler deadline registered
    [   21.266313] io scheduler cfq registered (default)
    [   21.266352] Boot video device is 0000:00:01.0
    [   21.266832] isapnp: Scanning for PnP cards...
    [   21.620745] isapnp: No Plug & Play device found
    [   21.701929] Real Time Clock Driver v1.12ac
    [   21.702239] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    [   21.702383] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [   21.702864] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    [   21.704142] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [   21.704754] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    [   21.706596] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
    [   21.707215] input: Macintosh mouse button emulation as /class/input/input0
    [   21.707501] PNP: No PS/2 controller found. Probing ports directly.
    [   21.710805] serio: i8042 KBD port at 0x60,0x64 irq 1
    [   21.710820] serio: i8042 AUX port at 0x60,0x64 irq 12
    [   21.711252] mice: PS/2 mouse device common for all mice
    [   21.711517] EISA: Probing bus 0 at eisa.0
    [   21.711536] Cannot allocate resource for EISA slot 1
    [   21.711541] Cannot allocate resource for EISA slot 2
    [   21.711570] EISA: Detected 0 cards.
    [   21.711806] TCP cubic registered
    [   21.711850] NET: Registered protocol family 1
    [   21.711916] Using IPI No-Shortcut mode
    [   21.712362]   Magic number: 9:129:693
    [   21.714317] Freeing unused kernel memory: 364k freed
    [   23.278786] AppArmor: AppArmor initialized<5>audit(1231004379.876:2):  type=1505 info="AppArmor initialized" pid=1179
    [   23.294809] fuse init (API version 7.8)
    [   23.307748] Failure registering capabilities with primary security module.
    [   23.319378] ACPI: Fan [FAN1] (on)
    [   23.332288] ACPI: Invalid PBLK length [5]
    [   23.340648] ACPI: Thermal Zone [THRM] (-269 C)
    [   25.002499] SCSI subsystem initialized
    [   25.020537] libata version 2.21 loaded.
    [   25.026279] ata_piix 0000:00:1f.1: version 2.11
    [   25.026411] PCI: Setting latency timer of device 0000:00:1f.1 to 64
    [   25.026717] scsi0 : ata_piix
    [   25.026826] scsi1 : ata_piix
    [   25.027051] ata1: PATA max UDMA/66 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011080 irq 14
    [   25.027058] ata2: PATA max UDMA/66 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011088 irq 15
    [   25.059305] usbcore: registered new interface driver usbfs
    [   25.059371] usbcore: registered new interface driver hub
    [   25.059430] usbcore: registered new device driver usb
    [   25.062811] USB Universal Host Controller Interface driver v3.0
    [   25.136037] 8139too Fast Ethernet driver 0.9.28
    [   25.197519] ata1.00: ATA-6: WDC WD800JB-00JJC0, 05.01C05, max UDMA/100
    [   25.197532] ata1.00: 156301488 sectors, multi 16: LBA
    [   25.197740] ata1.01: ATA-6: ST340810A, 3.39, max UDMA/100
    [   25.197745] ata1.01: 78165360 sectors, multi 16: LBA
    [   25.206888] ata1.00: configured for UDMA/66
    [   25.221608] ata1.01: configured for UDMA/66
    [   25.599912] Floppy drive(s): fd0 is 1.44M
    [   25.661000] FDC 0 is a post-1991 82077
    [   25.721245] ata2.00: ATAPI: ATAPI   DVD A  DH20A4H, QP59, max UDMA/66
    [   25.721270] ata2.01: ATAPI: _NEC DVD_RW ND-3550A, 1.05, max UDMA/33
    [   25.721282] ata2.00: limited to UDMA/33 due to 40-wire cable
    [   25.909203] ata2.00: configured for UDMA/33
    [   26.081185] ata2.01: configured for UDMA/33
    [   26.081542] scsi 0:0:0:0: Direct-Access     ATA      WDC WD800JB-00JJ 05.0 PQ: 0 ANSI: 5
    [   26.082622] scsi 0:0:1:0: Direct-Access     ATA      ST340810A        3.39 PQ: 0 ANSI: 5
    [   26.083897] scsi 1:0:0:0: CD-ROM            ATAPI    DVD A  DH20A4H   QP59 PQ: 0 ANSI: 5
    [   26.085502] scsi 1:0:1:0: CD-ROM            _NEC     DVD_RW ND-3550A  1.05 PQ: 0 ANSI: 5
    [   26.091585] ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 16
    [   26.091618] PCI: Setting latency timer of device 0000:00:1f.2 to 64
    [   26.091626] uhci_hcd 0000:00:1f.2: UHCI Host Controller
    [   26.091972] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
    [   26.092022] uhci_hcd 0000:00:1f.2: irq 16, io base 0x000010a0
    [   26.092338] usb usb1: configuration #1 chosen from 1 choice
    [   26.092395] hub 1-0:1.0: USB hub found
    [   26.092413] hub 1-0:1.0: 2 ports detected
    [   26.131307] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
    [   26.131391] sd 0:0:0:0: [sda] Write Protect is off
    [   26.131397] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [   26.131430] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [   26.131594] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
    [   26.131612] sd 0:0:0:0: [sda] Write Protect is off
    [   26.131617] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [   26.131644] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [   26.131659]  sda: sda1 sda2 < sda5 >
    [   26.186136] sd 0:0:0:0: [sda] Attached SCSI disk
    [   26.186638] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
    [   26.186668] sd 0:0:1:0: [sdb] Write Protect is off
    [   26.186674] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [   26.186705] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [   26.186827] sd 0:0:1:0: [sdb] 78165360 512-byte hardware sectors (40021 MB)
    [   26.186845] sd 0:0:1:0: [sdb] Write Protect is off
    [   26.186850] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    [   26.186878] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [   26.186886]  sdb:PCI: Enabling device 0000:01:0b.0 (0110 -> 0111)
    [   26.193259] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 18 (level, low) -> IRQ 17
    [   26.193286] uhci_hcd 0000:01:0b.0: UHCI Host Controller
    [   26.193335] uhci_hcd 0000:01:0b.0: new USB bus registered, assigned bus number 2
    [   26.193380] uhci_hcd 0000:01:0b.0: irq 17, io base 0x00002400
    [   26.193604] usb usb2: configuration #1 chosen from 1 choice
    [   26.193674] hub 2-0:1.0: USB hub found
    [   26.193691] hub 2-0:1.0: 2 ports detected
    [   26.204965]  sdb1
    [   26.205788] sd 0:0:1:0: [sdb] Attached SCSI disk
    [   26.219993] sd 0:0:0:0: Attached scsi generic sg0 type 0
    [   26.220477] sd 0:0:1:0: Attached scsi generic sg1 type 0
    [   26.220954] sr 1:0:0:0: Attached scsi generic sg2 type 5
    [   26.221374] scsi 1:0:1:0: Attached scsi generic sg3 type 5
    [   26.277615] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
    [   26.277635] Uniform CD-ROM driver Revision: 3.20
    [   26.277841] sr 1:0:0:0: Attached scsi CD-ROM sr0
    [   26.297304] PCI: Enabling device 0000:01:0b.1 (0110 -> 0111)
    [   26.297326] ACPI: PCI Interrupt 0000:01:0b.1[B] -> GSI 19 (level, low) -> IRQ 16
    [   26.297354] uhci_hcd 0000:01:0b.1: UHCI Host Controller
    [   26.297423] uhci_hcd 0000:01:0b.1: new USB bus registered, assigned bus number 3
    [   26.297463] uhci_hcd 0000:01:0b.1: irq 16, io base 0x00002420
    [   26.297690] usb usb3: configuration #1 chosen from 1 choice
    [   26.297746] hub 3-0:1.0: USB hub found
    [   26.297763] hub 3-0:1.0: 2 ports detected
    [   26.350961] sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
    [   26.351847] sr 1:0:1:0: Attached scsi CD-ROM sr1
    [   26.401286] PCI: Enabling device 0000:01:0d.0 (0110 -> 0111)
    [   26.401322] ACPI: PCI Interrupt 0000:01:0d.0[A] -> GSI 17 (level, low) -> IRQ 18
    [   26.401352] uhci_hcd 0000:01:0d.0: UHCI Host Controller
    [   26.401414] uhci_hcd 0000:01:0d.0: new USB bus registered, assigned bus number 4
    [   26.401461] uhci_hcd 0000:01:0d.0: irq 18, io base 0x00002440
    [   26.401751] usb usb4: configuration #1 chosen from 1 choice
    [   26.401829] hub 4-0:1.0: USB hub found
    [   26.401852] hub 4-0:1.0: 2 ports detected
    [   26.432942] usb 1-2: new full speed USB device using uhci_hcd and address 2
    [   26.505213] PCI: Enabling device 0000:01:0d.1 (0110 -> 0111)
    [   26.505235] ACPI: PCI Interrupt 0000:01:0d.1[B] -> GSI 18 (level, low) -> IRQ 17
    [   26.505264] uhci_hcd 0000:01:0d.1: UHCI Host Controller
    [   26.505329] uhci_hcd 0000:01:0d.1: new USB bus registered, assigned bus number 5
    [   26.505376] uhci_hcd 0000:01:0d.1: irq 17, io base 0x00002460
    [   26.505653] usb usb5: configuration #1 chosen from 1 choice
    [   26.505714] hub 5-0:1.0: USB hub found
    [   26.505733] hub 5-0:1.0: 2 ports detected
    [   26.587207] usb 1-2: configuration #1 chosen from 1 choice
    [   26.590070] hub 1-2:1.0: USB hub found
    [   26.592922] hub 1-2:1.0: 4 ports detected
    [   26.609356] PCI: Enabling device 0000:01:06.0 (0100 -> 0103)
    [   26.609374] ACPI: PCI Interrupt 0000:01:06.0[A] -> GSI 19 (level, low) -> IRQ 16
    [   26.609833] eth0: RealTek RTL8139 at 0xe0814000, 00:40:2b:3a:46:39, IRQ 16
    [   26.609838] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
    [   26.615064] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
    [   26.616937] PCI: Enabling device 0000:01:0b.2 (0110 -> 0112)
    [   26.616974] ACPI: PCI Interrupt 0000:01:0b.2[C] -> GSI 16 (level, low) -> IRQ 19
    [   26.617014] ehci_hcd 0000:01:0b.2: EHCI Host Controller
    [   26.617132] ehci_hcd 0000:01:0b.2: new USB bus registered, assigned bus number 6
    [   26.617225] ehci_hcd 0000:01:0b.2: irq 19, io mem 0xf4100400
    [   26.617237] ehci_hcd 0000:01:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    [   26.617489] usb usb6: configuration #1 chosen from 1 choice
    [   26.617557] hub 6-0:1.0: USB hub found
    [   26.617578] hub 6-0:1.0: 4 ports detected
    [   26.721160] PCI: Enabling device 0000:01:0d.2 (0110 -> 0112)
    [   26.721179] ACPI: PCI Interrupt 0000:01:0d.2[C] -> GSI 19 (level, low) -> IRQ 16
    [   26.721212] ehci_hcd 0000:01:0d.2: EHCI Host Controller
    [   26.721269] ehci_hcd 0000:01:0d.2: new USB bus registered, assigned bus number 7
    [   26.721354] ehci_hcd 0000:01:0d.2: irq 16, io mem 0xf4101000
    [   26.721365] ehci_hcd 0000:01:0d.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    [   26.721561] usb usb7: configuration #1 chosen from 1 choice
    [   26.721621] hub 7-0:1.0: USB hub found
    [   26.721639] hub 7-0:1.0: 4 ports detected
    [   26.825432] PCI: Enabling device 0000:01:0b.3 (0110 -> 0113)
    [   26.825449] ACPI: PCI Interrupt 0000:01:0b.3[A] -> GSI 18 (level, low) -> IRQ 17
    [   26.879509] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]  MMIO=[f4100800-f4100fff]  Max Packet=[2048]  IR/IT contexts=[4/8]
    [   27.027746] Attempting manual resume
    [   27.027757] swsusp: Resume From Partition 8:5
    [   27.027760] PM: Checking swsusp image.
    [   27.028159] PM: Resume from disk failed.
    [   27.104072] kjournald starting.  Commit interval 5 seconds
    [   27.104109] EXT3-fs: mounted filesystem with ordered data mode.
    [   27.974451] usb 1-2.2: new full speed USB device using uhci_hcd and address 3
    [   28.106654] usb 1-2.2: configuration #1 chosen from 1 choice
    [   28.109402] hub 1-2.2:1.0: USB hub found
    [   28.112346] hub 1-2.2:1.0: 4 ports detected
    [   28.156662] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[005022660014100e]
    [   28.644341] usb 2-2: new low speed USB device using uhci_hcd and address 2
    [   28.816552] usb 2-2: configuration #1 chosen from 1 choice
    [   29.022037] usb 1-2.2.1: new low speed USB device using uhci_hcd and address 4
    [   29.162240] usb 1-2.2.1: configuration #1 chosen from 1 choice
    [   29.369895] usb 1-2.2.3: new low speed USB device using uhci_hcd and address 5
    [   29.517098] usb 1-2.2.3: configuration #1 chosen from 1 choice
    [   37.652972] Linux agpgart interface v0.102 (c) Dave Jones
    [   37.666540] agpgart: Detected an Intel i810 Chipset.
    [   37.679053] agpgart: AGP aperture is 64M @ 0xf8000000
    [   37.774697] iTCO_vendor_support: vendor-support=0
    [   37.781766] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
    [   37.781999] iTCO_wdt: Found a ICH TCO device (Version=1, TCOBASE=0x1060)
    [   37.782146] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [   37.793387] intel_rng: FWH not detected
    [   37.890939] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [   37.896373] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [   38.269363] i810_smbus 0000:00:01.0: i810/i815 i2c device found.
    [   39.499325] input: PC Speaker as /class/input/input1
    [   40.158906] usbcore: registered new interface driver hiddev
    [   40.324541] hiddev96: USB HID v1.10 Device [CPS UPS AE550] on usb-0000:01:0b.0-2
    [   40.338690] input: Logitech USB Receiver as /class/input/input2
    [   40.338818] input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1f.2-2.2.1
    [   40.367805] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: Fixing up Logitech keyboard report descriptor
    [   40.369707] input: Logitech USB Receiver as /class/input/input3
    [   40.370019] input,hiddev97: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1f.2-2.2.1
    [   40.395141] input: No brand 2Port KVMSwicther as /class/input/input4
    [   40.395245] input: USB HID v1.10 Keyboard [No brand 2Port KVMSwicther] on usb-0000:00:1f.2-2.2.3
    [   40.404035] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: couldn't find an input interrupt endpoint
    [   40.404106] usbcore: registered new interface driver usbhid
    [   40.404114] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
    [   40.421213] usbcore: registered new interface driver xpad
    [   40.421226] /build/buildd/linux-source-2.6.22-2.6.22/drivers/input/joystick/xpad.c: driver for Xbox controllers v0.1.6
    [   40.932074] rtl_ieee80211_crypt: registered algorithm 'NULL'
    [   40.932085] rtl_ieee80211_crypt: registered algorithm 'TKIP'
    [   40.932090] rtl_ieee80211_crypt: registered algorithm 'WEP'
    [   40.932094] rtl_ieee80211_crypt: registered algorithm 'CCMP'
    [   40.984290]
    [   40.984294] Linux kernel driver for RTL8180 / RTL8185 based WLAN cards
    [   40.984301] Copyright (c) 2004-2005, Andrea Merello
    [   40.984305] rtl8180: Initializing module
    [   40.984308] rtl8180: Wireless extensions version 22
    [   40.984312] rtl8180: Initializing proc filesystem
    [   40.984424] rtl8180: Configuring chip resources
    [   40.984452] PCI: Enabling device 0000:01:0e.0 (0110 -> 0113)
    [   40.984465] ACPI: PCI Interrupt 0000:01:0e.0[A] -> GSI 16 (level, low) -> IRQ 19
    [   40.984614] rtl8180: Memory mapped space @ 0xf4101400
    [   40.984665] rtl8180: MAC controller is a RTL8185 b/g (V. D)
    [   40.984669] rtl8180: This is a CARDBUS NIC
    [   40.984673] rtl8180: Reported EEPROM chip is a 93c56 (2Kbit)
    [   40.990796] rtl8180: Card MAC address is 00:14:d1:3b:e3:05
    [   41.005937] rtl8180: EEPROM version 105
    [   41.007958] rtl8180: Card reports RF frontend Realtek 8225
    [   41.007963] rtl8180: WW:This driver has EXPERIMENTAL support for this chipset.
    [   41.007967] rtl8180: WW:use it with care and at your own risk and
    [   41.007971] rtl8180: WW:**PLEASE** REPORT SUCCESS/INSUCCESS TO andreamrl@tiscali.it
    [   41.007976] rtl8180: Energy threshold: b
    [   41.007980] rtl8180: PAPE from CONFIG2: 6
    [   41.029169] rtl8180: IRQ 19
    [   41.029900] rtl8180: Driver probe completed
    [   41.029906]
    [   41.069602] parport_pc 00:09: reported by Plug and Play ACPI
    [   41.069671] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
    [   41.525080] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 18
    [   41.525124] PCI: Setting latency timer of device 0000:00:1f.5 to 64
    [   42.193066] intel8x0_measure_ac97_clock: measured 54488 usecs
    [   42.193079] intel8x0: clocking to 48000
    [   43.176660] lp0: using parport0 (interrupt-driven).
    [   43.301372] Adding 1502036k swap on /dev/sda5.  Priority:-1 extents:1 across:1502036k
    [   43.628551] EXT3 FS on sda1, internal journal
    [   45.530738] No dock devices found.
    [   45.824163] input: Power Button (FF) as /class/input/input5
    [   45.824880] ACPI: Power Button (FF) [PWRF]
    [   45.856186] input: Power Button (CM) as /class/input/input6
    [   45.856858] ACPI: Power Button (CM) [PWRB]
    [   48.508567] eth0: link down
    [   48.625235] rtl8180: Bringing up iface
    [   48.833730] rtl8180: Card successfully reset
    [   50.291926] ppdev: user-space parallel port driver
    [   50.509117] audit(1231004408.474:3):  type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4844 profile="/usr/sbin/cupsd"
    [   50.686045] apm: BIOS not found.
    [   52.922793] Failure registering capabilities with primary security module.
    [   53.210770] Bluetooth: Core ver 2.11
    [   53.211004] NET: Registered protocol family 31
    [   53.211009] Bluetooth: HCI device and connection manager initialized
    [   53.211017] Bluetooth: HCI socket layer initialized
    [   53.281527] Bluetooth: L2CAP ver 2.8
    [   53.281539] Bluetooth: L2CAP socket layer initialized
    [   53.382198] Bluetooth: RFCOMM socket layer initialized
    [   53.382405] Bluetooth: RFCOMM TTY layer initialized
    [   53.382411] Bluetooth: RFCOMM ver 1.8    
    
    INFO HIDEN:~$ dmesg | grep firmware
    INFO HIDEN:~$
    PS:

    let me know if you need anymore info from me

    thanks for any and all help that can be given to me!!!1

  2. #2
    Please retry the lspci -nn command, you must have mistyped it. If you get the same result, then just use lspci without any options.

    It appears that the system sees the wireless as a rtl8180 wireless. But the output of lsmod list the driver as r8180. If this is not a typo, then there is a problem with the driver module.

    I would recommend installing a newer version of Kubuntu. Version 8.10 is now available. Otherwise, upgrade the kernel to the latest version available.
    Please do not send Private Messages to me with requests for help. I will not reply.

  3. #3

    Cool

    Quote Originally Posted by waterhead View Post
    Please retry the lspci -nn command, you must have mistyped it. If you get the same result, then just use lspci without any options.

    It appears that the system sees the wireless as a rtl8180 wireless. But the output of lsmod list the driver as r8180. If this is not a typo, then there is a problem with the driver module.

    I would recommend installing a newer version of Kubuntu. Version 8.10 is now available. Otherwise, upgrade the kernel to the latest version available.
    is the command --nn ( - - n n) or is it -nn

    because I thought I saw --nn in the fourms here on this site or in the wireless internet of this site

    thanks

  4. $spacer_open
    $spacer_close
  5. #4
    The command is this:
    Code:
    lspci -nn
    Take a look at the "Usage" output in your first post. You can also just use this command, without the -nn option.
    Code:
    lspci
    Please do not send Private Messages to me with requests for help. I will not reply.

  6. #5

    Angry

    Quote Originally Posted by waterhead View Post
    Please retry the lspci -nn command, you must have mistyped it. If you get the same result, then just use lspci without any options.

    It appears that the system sees the wireless as a rtl8180 wireless. But the output of lsmod list the driver as r8180. If this is not a typo, then there is a problem with the driver module.

    I would recommend installing a newer version of Kubuntu. Version 8.10 is now available. Otherwise, upgrade the kernel to the latest version available.
    Ok thanks for then info but I have not beable to get the info you have ask for just yet because I have been on my laptop for the last few days I have an issues with kubuntu v. 7.10 that I don't know how to fix which cause the delay in getting the info you have ask for and the issue I have is at times my desktop computer (that has kubuntu v7.10 on it) lockup or I can't use my keyboard and/or mouse I have a Logitech cardless desktop ex110 keybord and mouse which is being used on a KVM switch for my computer and laptop and what I would like to know is if my computer is supported by linux (the version I am using) or why this might happen and if this keeps happening I will not be able to use linux for my desktop computer and will have to go back to windows XP HOME and my computer is about 5 to 7 year old too and have added some of the PCI cards like the 4 port USB PCI and 3 USB + 2FIREWIRE (note: I have not added the one that can be used from the inside of the case for firewire and usb port(s))

    OH wait a min I just turn on my other computer and have the info and did not want to retype or redo some of this so I am going to paste the info from my linux desktop comuter for the info that you need but I would like to know how to unlock my PC from lockup if that can be done if not alwell but do give me the info just incase I can fix it later on thanks

    output file belw:

    Code:
    info@removed by user:~$ lspci -nn
    00:00.0 Host bridge [0600]: Intel Corporation 82810E DC-133 (GMCH) Graphics Memory Controller Hub [8086:7124] (rev 03)
    00:01.0 VGA compatible controller [0300]: Intel Corporation 82810E DC-133 (CGC) Chipset Graphics Controller [8086:7125] (rev 03)
    00:1e.0 PCI bridge [0604]: Intel Corporation 82801AA PCI Bridge [8086:2418] (rev 02)
    00:1f.0 ISA bridge [0601]: Intel Corporation 82801AA ISA Bridge (LPC) [8086:2410] (rev 02)
    00:1f.1 IDE interface [0101]: Intel Corporation 82801AA IDE Controller [8086:2411] (rev 02)
    00:1f.2 USB Controller [0c03]: Intel Corporation 82801AA USB Controller [8086:2412] (rev 02)
    00:1f.3 SMBus [0c05]: Intel Corporation 82801AA SMBus Controller [8086:2413] (rev 02)
    00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801AA AC'97 Audio Controller [8086:2415] (rev 02)
    01:06.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
    01:0b.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 61)
    01:0b.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 61)
    01:0b.2 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 63)
    01:0b.3 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. IEEE 1394 Host Controller [1106:3044] (rev 46)
    01:0d.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 61)
    01:0d.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 61)
    01:0d.2 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 63)
    01:0e.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185] (rev 20)
    info@removed by user:~$
    I hope this would help?

  7. #6
    Thank you

    This is the wireless card.
    Code:
    01:0e.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185] (rev 20)
    It uses the rtl818x driver. Here is some info on it:

    Main Page - Realtek Linux wireless driver

    The driver is the Linux kernel starting in version 2.6.25. This is why I recommend upgrading, either the kernel or just use a newer version of Ubuntu.

    As for your lock up problems. Does this PC have windows on it? Does it lock up in widows too?

    I see that this motherboard has a lot of Via components on it. If this is a Via mobo, then it may have bad capacitors I have two Via motherboards that suffered constant freeze ups, and they have bad capacitors on them. The bad capacitors will have bulging tops, sometimes there will be a crusty substance oozing from the top or bottom. Please check for this problem.

    There is no cure, except to replace the capacitors or the entire motherboard. If you are experienced with soldering, you can do it yourself for as little as $20USD.
    Last edited by waterhead; 01-15-2009 at 11:15 AM.
    Please do not send Private Messages to me with requests for help. I will not reply.

  8. #7

    Angry reply about lockups

    Quote Originally Posted by waterhead View Post
    Thank you

    This is the wireless card.
    Code:
    01:0e.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185] (rev 20)
    It uses the rtl818x driver. Here is some info on it:

    Main Page - Realtek Linux wireless driver

    The driver is the Linux kernel starting in version 2.6.25. This is why I recommend upgrading, either the kernel or just use a newer version of Ubuntu.

    As for your lock up problems. Does this PC have windows on it? Does it lock up in widows too?

    I see that this motherboard has a lot of Via components on it. If this is a Via mobo, then it may have bad capacitors I have two Via motherboards that suffered constant freeze ups, and they have bad capacitors on them. The bad capacitors will have bulging tops, sometimes there will be a crusty substance oozing from the top or bottom. Please check for this problem.

    There is no cure, except to replace the capacitors or the entire motherboard. If you are experienced with soldering, you can do it yourself for as little as $20USD.
    NO I DON'T HAVE WINDOWS INSTALLED ANYMORE BUT HAVE TWO HDD ONE IS A 40GB HDD AND THE OTHER IS 80GB HDD AND I CAN'T GET MY 40GB TO MOUNT BUT THAT ISSUSE I HAVE DONE A NEW TOPIC FOR THAT SO THAT IS NOT NEEDED RIGHT NOW AND I INSTALLED KUBUNTU 7.10 ON THIS COMPUTER WIT WINDOWS HOME XP SP3 WAS INSTALLED

    and it does the lockup on the live cd too and it seem to me that as long as I am moving the mouse around with out stopping it would not lockup at all

    and windows was first install on the 40GB HDD and then I changed it to be the 80GB HDD and my computer is about 5 to 7 years old and just had the power supply replace about a year ago

    and I need the 3 port USB 2.0 hub + 2 firewire port because I do video editing on my computer I will how to do and get that software on my computer later on but it is a good thing I can use my vista laptop computer to do some of the editing and I have two portable hdd one is 120GB hdd USB and FIREWIRE and the other HDD is 500GB seagate drive

    and have replaced my cd rom drive(s) it came w/ an CD-RW but installed a DVD-RW DL burner then I got a Lightscribe CD/DVD DL burner in my computer so that is 2 DVD DL burners but their is only ONE DVD DL BURNER that has light scribe in my computer but have TWO DVD DL burners in my computer and it is an HP 510n computer

    and I will have to let you know if Kubuntu 8 or 8.10 works because I have just downloaded the iso file and burned it to a cd the file size was 699MB so I put it on a CD but could not get fedroa (don't know which version) to work or installed on my computer I have it on a CD too but it would not work it would try to load but did not or stops after some time or the progress bar stops when it gets full (white) but it is does not matter because I would like to get KUBUNTU to work more then that version of linux anyways!

    and my computer had only has 2 RAM slot on the motherboard which only had one 256MB and now I have 2x 256MB which give me 512MB of RAM which my computer take PC100 SDRAM


    1.2GHz intel celeron processory

    just thought I would give you some more info about my computer to see if that would helps out!

  9. #8

    reply about downloading

    Quote Originally Posted by waterhead View Post
    Thank you

    This is the wireless card.
    Code:
    01:0e.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185] (rev 20)
    It uses the rtl818x driver. Here is some info on it:

    Main Page - Realtek Linux wireless driver

    The driver is the Linux kernel starting in version 2.6.25. This is why I recommend upgrading, either the kernel or just use a newer version of Ubuntu.

    As for your lock up problems. Does this PC have windows on it? Does it lock up in widows too?

    I see that this motherboard has a lot of Via components on it. If this is a Via mobo, then it may have bad capacitors I have two Via motherboards that suffered constant freeze ups, and they have bad capacitors on them. The bad capacitors will have bulging tops, sometimes there will be a crusty substance oozing from the top or bottom. Please check for this problem.

    There is no cure, except to replace the capacitors or the entire motherboard. If you are experienced with soldering, you can do it yourself for as little as $20USD.
    I tried the link you give but it does not tell me how to download and install it

    when I download file for linux (because I can't use the wireless card) is I first download the file on my windows computer and then copy the file over to a flash drive and copy the file from the flash drive over to the linux computer

    thanks for any help!

    PS:

    don't have a long internet cable for my computer!
    that is why I went wireless

  10. #9
    The driver is not available as a "package" that can be installed. You would have to download the source files using the Subversion program, and then compile the source files.

    This process usually needs other programs and files installed first. For example, you need the Subversion program. Since you do not have an internet connection, you will find this to be very difficult. This is why I recommend you downloading Ubuntu 8.10 and installing that. Your wireless driver should be already installed for you.

    By the way, how are the capacitors on the motherboard? This may very well be the cause of your computer freezing, yet you seem to have dismissed it.
    Please do not send Private Messages to me with requests for help. I will not reply.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •