#1 permalink Linux Guru
Join Date: Jul 2008
Location: Pecos, Texas
Posts: 1,503
Xubuntu 8.04 Belkin F5D 7010 Ver6000 PCMCIA
Just installed Xubuntu 8.04 on IBM T23, P3 1.2 GHZ, 256 mb ram, 40 gig partition.
Wireless PCMCIA Card Is a Belkin F5D 7010 version 6000
uname -r
lsmod
Code:
Module Size Used by
savage 33920 2
drm 82452 3 savage
af_packet 23812 2
rfcomm 41744 2
l2cap 25728 13 rfcomm
bluetooth 61028 4 rfcomm,l2cap
uinput 10240 0
thinkpad_acpi 51836 0
nvram 9992 1 thinkpad_acpi
ppdev 10372 0
ipv6 267908 10
speedstep_ich 6288 0
speedstep_lib 6532 1 speedstep_ich
cpufreq_userspace 5284 0
cpufreq_conservative 8712 0
cpufreq_stats 7104 0
cpufreq_ondemand 9740 1
freq_table 5536 3 speedstep_ich,cpufreq_stats,cpufreq_ondemand
cpufreq_powersave 2688 0
sbs 15112 0
sbshc 7680 1 sbs
bay 6912 0
container 5632 0
dock 11280 1 bay
iptable_filter 3840 0
ip_tables 14820 1 iptable_filter
x_tables 16132 1 ip_tables
lp 12324 0
loop 18948 0
arc4 2944 2
ecb 4480 2
blkcipher 8324 1 ecb
rt61pci 25472 0
rt2x00pci 11264 1 rt61pci
rt2x00lib 22528 2 rt61pci,rt2x00pci
rfkill 8596 1 rt2x00lib
input_polldev 5896 1 rt2x00lib
crc_itu_t 3072 1 rt2x00lib
mac80211 165652 3 rt61pci,rt2x00pci,rt2x00lib
cfg80211 15112 1 mac80211
eeprom_93cx6 3200 1 rt61pci
pcmcia 40876 0
snd_intel8x0 35356 2
snd_ac97_codec 101028 1 snd_intel8x0
irtty_sir 9728 0
ac97_bus 3072 1 snd_ac97_codec
sir_dev 17412 1 irtty_sir
snd_pcm_oss 42144 0
snd_mixer_oss 17920 1 snd_pcm_oss
nsc_ircc 24208 0
irda 203068 3 irtty_sir,sir_dev,nsc_ircc
battery 14212 0
crc_ccitt 3072 1 irda
ac 6916 0
parport_pc 36260 1
parport 37832 3 ppdev,lp,parport_pc
snd_pcm 78596 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
evdev 13056 6
snd_seq_dummy 4868 0
video 19856 0
output 4736 1 video
serio_raw 7940 0
psmouse 40336 0
snd_seq_oss 35584 0
yenta_socket 27276 3
rsrc_nonstatic 13696 1 yenta_socket
snd_seq_midi 9376 0
pcmcia_core 40596 3 pcmcia,yenta_socket,rsrc_nonstatic
snd_rawmidi 25760 1 snd_seq_midi
snd_seq_midi_event 8320 2 snd_seq_oss,snd_seq_midi
snd_seq 54224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 24836 2 snd_pcm,snd_seq
snd_seq_device 9612 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 56996 15 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_dummy,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
button 9232 0
pcspkr 4224 0
soundcore 8800 1 snd
snd_page_alloc 11400 2 snd_intel8x0,snd_pcm
iTCO_wdt 13092 0
iTCO_vendor_support 4868 1 iTCO_wdt
shpchp 34452 0
intel_agp 25492 1
pci_hotplug 30880 1 shpchp
agpgart 34760 2 drm,intel_agp
ext3 136840 1
jbd 48404 1 ext3
mbcache 9600 1 ext3
sg 36880 0
sr_mod 17956 0
cdrom 37408 1 sr_mod
sd_mod 30720 3
floppy 59588 0
ata_piix 19588 2
ata_generic 8324 0
pata_acpi 8320 0
e100 37388 0
mii 6400 1 e100
libata 159600 3 ata_piix,ata_generic,pata_acpi
scsi_mod 151436 4 sg,sr_mod,sd_mod,libata
uhci_hcd 27024 0
usbcore 146412 2 uhci_hcd
thermal 16796 0
processor 36488 2 thermal
fan 5636 0
fbcon 42912 0
tileblit 3456 1 fbcon
font 9472 1 fbcon
bitblit 6784 1 fbcon
softcursor 3072 1 bitblit
fuse 50708 1
dmesg
Code:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.24-23-generic (buildd@vernadsky) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Mon Jan 26 00:13:11 UTC 2009 (Ubuntu 2.6.24-23.48-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000ff60000 (usable)
[ 0.000000] BIOS-e820: 000000000ff60000 - 000000000ff7a000 (ACPI data)
[ 0.000000] BIOS-e820: 000000000ff7a000 - 000000000ff7c000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000000ff7c000 - 0000000010000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 255MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 65376) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 65376
[ 0.000000] HighMem 65376 -> 65376
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 65376
[ 0.000000] On node 0 totalpages: 65376
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 478 pages used for memmap
[ 0.000000] Normal zone: 60802 pages, LIFO batch:15
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F7440 checksum 0
[ 0.000000] ACPI: RSDP 000F7440, 0024 (r2 IBM )
[ 0.000000] ACPI: XSDT 0FF6FD7F, 0044 (r1 IBM TP-1A 1130 LTP 0)
[ 0.000000] ACPI: FACP 0FF6FDC3, 0081 (r1 IBM TP-1A 1130 IBM 1)
[ 0.000000] ACPI: DSDT 0FF6FEAA, A0DD (r1 IBM TP-1A 1130 MSFT 100000D)
[ 0.000000] ACPI: FACS 0FF7B000, 0040
[ 0.000000] ACPI: SSDT 0FF6FE77, 0033 (r1 IBM TP-1A 1130 MSFT 100000D)
[ 0.000000] ACPI: ECDT 0FF79F87, 0051 (r1 IBM TP-1A 1130 IBM 1)
[ 0.000000] ACPI: BOOT 0FF79FD8, 0028 (r1 IBM TP-1A 1130 LTP 1)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 10000000:ef800000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000dc000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64866
[ 0.000000] Kernel command line: root=UUID=4ecf04f2-97fd-459b-ad77-ef0d5ffeb3d7 ro quiet splash
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] mapped APIC to ffffb000 (0120c000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 1199.024 MHz processor.
[ 9.696007] Console: colour VGA+ 80x25
[ 9.696015] console [tty0] enabled
[ 9.696179] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 9.696392] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 9.711381] Memory: 247292k/261504k available (2179k kernel code, 13720k reserved, 1008k data, 368k init, 0k highmem)
[ 9.711396] virtual kernel memory layout:
[ 9.711398] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 9.711400] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 9.711402] vmalloc : 0xd0800000 - 0xff7fe000 ( 751 MB)
[ 9.711405] lowmem : 0xc0000000 - 0xcff60000 ( 255 MB)
[ 9.711407] .init : 0xc0423000 - 0xc047f000 ( 368 kB)
[ 9.711409] .data : 0xc0320c08 - 0xc041cdc4 (1008 kB)
[ 9.711412] .text : 0xc0100000 - 0xc0320c08 (2179 kB)
[ 9.711417] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 9.711480] SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 9.791506] Calibrating delay using timer specific routine.. 2399.98 BogoMIPS (lpj=4799964)
[ 9.791554] Security Framework initialized
[ 9.791568] SELinux: Disabled at boot.
[ 9.791593] AppArmor: AppArmor initialized
[ 9.791599] Failure registering capabilities with primary security module.
[ 9.791614] Mount-cache hash table entries: 512
[ 9.791812] Initializing cgroup subsys ns
[ 9.791819] Initializing cgroup subsys cpuacct
[ 9.791836] CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 9.791855] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 9.791859] CPU: L2 cache: 512K
[ 9.791864] CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 00000000
[ 9.791880] Compat vDSO mapped to ffffe000.
[ 9.791898] Checking 'hlt' instruction... OK.
[ 9.807982] SMP alternatives: switching to UP code
[ 9.810443] Freeing SMP alternatives: 11k freed
[ 9.810630] Early unpacking initramfs... done
[ 10.367429] ACPI: Core revision 20070126
[ 10.367714] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 10.374499] ACPI: setting ELCR to 0200 (from 0800)
[ 10.393946] CPU0: Intel Mobile Intel(R) Pentium(R) III CPU - M 1200MHz stepping 04
[ 10.393958] SMP motherboard not detected.
[ 10.393962] Local APIC not detected. Using dummy APIC emulation.
[ 10.394051] Brought up 1 CPUs
[ 10.394084] CPU0 attaching sched-domain:
[ 10.394089] domain 0: span 01
[ 10.394092] groups: 01
[ 10.394451] net_namespace: 64 bytes
[ 10.394464] Booting paravirtualized kernel on bare hardware
[ 10.395401] Time: 20:26:02 Date: 02/10/09
[ 10.395460] NET: Registered protocol family 16
[ 10.395871] EISA bus registered
[ 10.395889] ACPI: bus type pci registered
[ 10.396340] PCI: PCI BIOS revision 2.10 entry at 0xfd8fe, last bus=8
[ 10.396345] PCI: Using configuration type 1
[ 10.396354] Setting up standard PCI resources
[ 10.401899] ACPI: EC: EC description table is found, configuring boot EC
[ 10.409087] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 10.417505] ACPI: Interpreter enabled
[ 10.417510] ACPI: (supports S0 S3 S4 S5)
[ 10.417534] ACPI: Using PIC for interrupt routing
[ 10.428959] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[ 10.428966] ACPI: EC: driver started in poll mode
[ 10.429193] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 10.429521] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[ 10.429527] PCI quirk: region 1180-11bf claimed by ICH4 GPIO
[ 10.429987] PCI: Transparent bridge - 0000:00:1e.0
[ 10.430151] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 10.430242] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 10.430278] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 10.435301] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[ 10.435672] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
[ 10.435982] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
[ 10.436292] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[ 10.436601] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
[ 10.436884] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[ 10.437167] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[ 10.437451] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
[ 10.437926] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 10.438130] ACPI: Power Resource [PUBS] (on)
[ 10.438207] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 10.438264] pnp: PnP ACPI init
[ 10.438280] ACPI: bus type pnp registered
[ 10.440063] pnpacpi: exceeded the max number of mem resources: 12
[ 10.444100] pnp: PnP ACPI: found 13 devices
[ 10.444106] ACPI: ACPI bus type pnp unregistered
[ 10.444112] PnPBIOS: Disabled by ACPI PNP
[ 10.444541] PCI: Using ACPI for IRQ routing
[ 10.444547] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 10.463511] NET: Registered protocol family 8
[ 10.463515] NET: Registered protocol family 20
[ 10.463643] AppArmor: AppArmor Filesystem Enabled
[ 10.467495] Time: tsc clocksource has been installed.
[ 10.475561] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 10.475567] system 00:00: iomem range 0xc0000-0xc3fff could not be reserved
[ 10.475573] system 00:00: iomem range 0xc4000-0xc7fff could not be reserved
[ 10.475578] system 00:00: iomem range 0xc8000-0xcbfff could not be reserved
[ 10.475583] system 00:00: iomem range 0xcc000-0xcffff could not be reserved
[ 10.475588] system 00:00: iomem range 0x0-0x0 could not be reserved
[ 10.475593] system 00:00: iomem range 0x0-0x0 could not be reserved
[ 10.475597] system 00:00: iomem range 0x0-0x0 could not be reserved
[ 10.475602] system 00:00: iomem range 0xdc000-0xdffff has been reserved
[ 10.475607] system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
[ 10.475612] system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
[ 10.475617] system 00:00: iomem range 0xe8000-0xebfff could not be reserved
[ 10.475630] system 00:02: ioport range 0x1000-0x107f has been reserved
[ 10.475635] system 00:02: ioport range 0x1180-0x11bf has been reserved
[ 10.475640] system 00:02: ioport range 0x15e0-0x15ef has been reserved
[ 10.475644] system 00:02: ioport range 0x1600-0x167f has been reserved
[ 10.506386] PCI: Bridge: 0000:00:01.0
[ 10.506390] IO window: disabled.
[ 10.506395] MEM window: c0100000-c01fffff
[ 10.506399] PREFETCH window: e0000000-ebffffff
[ 10.506410] PCI: Bus 3, cardbus bridge: 0000:02:00.0
[ 10.506414] IO window: 00002000-000020ff
[ 10.506419] IO window: 00002400-000024ff
[ 10.506424] PREFETCH window: f0000000-f3ffffff
[ 10.506429] MEM window: c4000000-c7ffffff
[ 10.506434] PCI: Bus 7, cardbus bridge: 0000:02:00.1
[ 10.506437] IO window: 00002800-000028ff
[ 10.506442] IO window: 00002c00-00002cff
[ 10.506447] PREFETCH window: f4000000-f7ffffff
[ 10.506452] MEM window: c8000000-cbffffff
[ 10.506457] PCI: Bridge: 0000:00:1e.0
[ 10.506461] IO window: 2000-6fff
[ 10.506466] MEM window: c0200000-cfffffff
[ 10.506471] PREFETCH window: f0000000-f7ffffff
[ 10.506489] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 10.507110] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 10.507116] PCI: setting IRQ 11 as level-triggered
[ 10.507121] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 10.507671] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 10.507675] ACPI: PCI Interrupt 0000:02:00.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 10.507706] NET: Registered protocol family 2
[ 10.547627] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 10.548037] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 10.548166] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 10.548292] TCP: Hash tables configured (established 8192 bind 8192)
[ 10.548297] TCP reno registered
[ 10.559725] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[ 11.035562] it is
[ 11.610378] Freeing initrd memory: 7317k freed
[ 11.610822] Simple Boot Flag at 0x35 set to 0x1
[ 11.611574] audit: initializing netlink socket (disabled)
[ 11.611604] audit(1234297562.888:1): initialized
[ 11.615696] VFS: Disk quotas dquot_6.5.1
[ 11.615876] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 11.616174] io scheduler noop registered
[ 11.616179] io scheduler anticipatory registered
[ 11.616183] io scheduler deadline registered
[ 11.616208] io scheduler cfq registered (default)
[ 11.616281] Boot video device is 0000:01:00.0
[ 11.616295] PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling
[ 11.616814] isapnp: Scanning for PnP cards...
[ 11.969933] isapnp: No Plug & Play device found
[ 12.024832] Real Time Clock Driver v1.12ac
[ 12.025005] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 12.026608] serial 00:0a: activated
[ 12.027001] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
[ 12.028429] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 12.028547] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 12.028733] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 12.035862] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 12.035871] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 12.047464] mice: PS/2 mouse device common for all mice
[ 12.047664] EISA: Probing bus 0 at eisa.0
[ 12.047674] Cannot allocate resource for EISA slot 1
[ 12.047680] Cannot allocate resource for EISA slot 2
[ 12.047683] Cannot allocate resource for EISA slot 3
[ 12.047687] Cannot allocate resource for EISA slot 4
[ 12.047690] Cannot allocate resource for EISA slot 5
[ 12.047694] Cannot allocate resource for EISA slot 6
[ 12.047703] EISA: Detected 0 cards.
[ 12.047708] cpuidle: using governor ladder
[ 12.047712] cpuidle: using governor menu
[ 12.048000] NET: Registered protocol family 1
[ 12.048053] Using IPI No-Shortcut mode
[ 12.048114] registered taskstats version 1
[ 12.048305] Magic number: 13:222:447
[ 12.048497] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 12.048501] EDD information not available.
[ 12.048930] Freeing unused kernel memory: 368k freed
[ 12.048990] Write protecting the kernel read-only data: 806k
[ 12.053536] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 13.385299] fuse init (API version 7.9)
[ 13.431981] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 13.437385] ACPI: Thermal Zone [THM0] (65 C)
[ 14.515281] usbcore: registered new interface driver usbfs
[ 14.515327] usbcore: registered new interface driver hub
[ 14.531243] usbcore: registered new device driver usb
[ 14.549906] USB Universal Host Controller Interface driver v3.0
[ 14.550042] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 14.550063] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 14.550070] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 14.550598] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 14.550634] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
[ 14.550883] usb usb1: configuration #1 chosen from 1 choice
[ 14.550929] hub 1-0:1.0: USB hub found
[ 14.550941] hub 1-0:1.0: 2 ports detected
[ 14.651983] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 14.651993] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 14.652011] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 14.652018] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 14.652064] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 14.652096] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
[ 14.652299] usb usb2: configuration #1 chosen from 1 choice
[ 14.652342] hub 2-0:1.0: USB hub found
[ 14.652354] hub 2-0:1.0: 2 ports detected
[ 14.710247] SCSI subsystem initialized
[ 14.756003] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 14.756013] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 14.756033] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 14.756039] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 14.756086] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 14.756118] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
[ 14.756325] usb usb3: configuration #1 chosen from 1 choice
[ 14.756370] hub 3-0:1.0: USB hub found
[ 14.756381] hub 3-0:1.0: 2 ports detected
[ 14.858443] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 14.858452] e100: Copyright(c) 1999-2006 Intel Corporation
[ 14.861275] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
[ 14.861285] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
[ 14.885881] e100: eth0: e100_probe: addr 0xc0200000, irq 11, MAC addr 00:d0:59:cc:ba:8a
[ 14.891138] libata version 3.00 loaded.
[ 14.907524] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[ 14.907544] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 14.907610] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 14.907631] ACPI: PCI interrupt for device 0000:00:1f.1 disabled
[ 14.940390] ata_piix 0000:00:1f.1: version 2.12
[ 14.940428] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 14.940499] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 14.961641] scsi0 : ata_piix
[ 14.968300] scsi1 : ata_piix
[ 14.969886] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1860 irq 14
[ 14.969892] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1868 irq 15
[ 15.043232] Floppy drive(s): fd0 is 1.44M
[ 15.062138] FDC 0 is a National Semiconductor PC87306
[ 15.131547] ata1.00: ATA-6: ST980815A, 3.ALD, max UDMA/100
[ 15.131556] ata1.00: 156301488 sectors, multi 16: LBA48
[ 15.147473] ata1.00: configured for UDMA/100
[ 15.467485] ata2.00: ATAPI: MATSHITADVD-ROM SR-8176, LB36, max UDMA/33
[ 15.631319] ata2.00: configured for UDMA/33
[ 15.631574] scsi 0:0:0:0: Direct-Access ATA ST980815A 3.AL PQ: 0 ANSI: 5
[ 15.632446] scsi 1:0:0:0: CD-ROM MATSHITA DVD-ROM SR-8176 LB36 PQ: 0 ANSI: 5
[ 15.804410] Driver 'sd' needs updating - please use bus_type methods
[ 15.807103] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 15.807134] sd 0:0:0:0: [sda] Write Protect is off
[ 15.807139] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 15.807179] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.807275] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 15.807297] sd 0:0:0:0: [sda] Write Protect is off
[ 15.807302] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 15.807339] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.807347] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 15.819664] sda1 sda2 sda3
[ 15.821020] sd 0:0:0:0: [sda] Attached SCSI disk
[ 15.833960] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 15.833972] Uniform CD-ROM driver Revision: 3.20
[ 15.834063] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 15.834501] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 15.834530] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 16.003006] Clocksource tsc unstable (delta = -1347408511 ns)
[ 16.007032] Time: acpi_pm clocksource has been installed.
[ 16.055154] Attempting manual resume
[ 16.055161] swsusp: Resume From Partition 8:3
[ 16.055164] PM: Checking swsusp image.
[ 16.055488] PM: Resume from disk failed.
[ 16.097664] kjournald starting. Commit interval 5 seconds
[ 16.097694] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.718454] Linux agpgart interface v0.102
[ 19.809368] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 19.872714] agpgart: Detected an Intel 830M Chipset.
[ 19.952677] agpgart: AGP aperture is 256M @ 0xd0000000
[ 19.965735] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 20.050399] intel_rng: FWH not detected
[ 20.215459] iTCO_vendor_support: vendor-support=0
[ 20.296551] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 20.304589] iTCO_wdt: Found a ICH3-M TCO device (Version=1, TCOBASE=0x1060)
[ 20.304667] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 20.516783] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 20.918950] input: Power Button (FF) as /devices/virtual/input/input3
[ 20.928399] ACPI: Power Button (FF) [PWRF]
[ 20.928594] input: Lid Switch as /devices/virtual/input/input4
[ 20.936860] ACPI: Lid Switch [LID]
[ 20.937032] input: Sleep Button (CM) as /devices/virtual/input/input5
[ 20.948383] ACPI: Sleep Button (CM) [SLPB]
[ 22.736383] Yenta: CardBus bridge found at 0000:02:00.0 [1014:023b]
[ 22.736407] Yenta: Using INTVAL to route CSC interrupts to PCI
[ 22.736410] Yenta: Routing CardBus interrupts to PCI
[ 22.736416] Yenta TI: socket 0000:02:00.0, mfunc 0x01d21022, devctl 0x64
[ 22.968726] Yenta: ISA IRQ mask 0x04b8, PCI irq 11
[ 22.968735] Socket status: 30000006
[ 22.968742] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x6fff
[ 22.968748] cs: IO port probe 0x2000-0x6fff: clean.
[ 22.970516] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
[ 22.970521] pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf7ffffff
[ 23.023007] Yenta: CardBus bridge found at 0000:02:00.1 [1014:023b]
[ 23.023028] Yenta: Using INTVAL to route CSC interrupts to PCI
[ 23.023031] Yenta: Routing CardBus interrupts to PCI
[ 23.023037] Yenta TI: socket 0000:02:00.1, mfunc 0x01d21022, devctl 0x64
[ 23.252678] Yenta: ISA IRQ mask 0x04b8, PCI irq 11
[ 23.252687] Socket status: 30000020
[ 23.252695] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x6fff
[ 23.252701] cs: IO port probe 0x2000-0x6fff: clean.
[ 23.254445] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff
[ 23.254450] pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf7ffffff
[ 23.323959] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[ 23.342614] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input6
[ 23.960011] pccard: CardBus card inserted into slot 1
[ 24.411492] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:03/LNXVIDEO:00/input/input7
[ 24.419969] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 25.783162] parport_pc 00:0b: reported by Plug and Play ACPI
[ 25.783209] parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
[ 25.803399] ACPI: AC Adapter [AC] (on-line)
[ 25.895941] irda_init()
[ 25.895992] NET: Registered protocol family 23
[ 25.900640] ACPI: Battery Slot [BAT0] (battery present)
[ 25.946141] nsc-ircc 00:0c: activated
[ 25.946152] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
[ 25.946179] nsc-ircc, chip->init
[ 25.946189] nsc-ircc, Found chip at base=0x02e
[ 25.946214] nsc-ircc, driver loaded (Dag Brattli)
[ 25.946722] IrDA: Registered device irda0
[ 25.946727] nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500
[ 26.101858] PCI: Enabling device 0000:00:1f.5 (0000 -> 0001)
[ 26.101877] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 26.101902] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 26.819725] intel8x0_measure_ac97_clock: measured 55705 usecs
[ 26.819735] intel8x0: clocking to 48000
[ 28.159604] PCI: Enabling device 0000:07:00.0 (0000 -> 0002)
[ 28.159626] ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 28.159639] PCI: Setting latency timer of device 0000:07:00.0 to 64
[ 28.178909] phy0: Selected rate control algorithm 'simple'
[ 28.211831] cs: IO port probe 0x100-0x3af: clean.
[ 28.212711] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 28.213111] cs: IO port probe 0x820-0x8ff: clean.
[ 28.213456] cs: IO port probe 0xc00-0xcf7: clean.
[ 28.214024] cs: IO port probe 0xa00-0xaff: clean.
[ 28.214735] cs: IO port probe 0x100-0x3af: clean.
[ 28.215629] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 28.216028] cs: IO port probe 0x820-0x8ff: clean.
[ 28.216373] cs: IO port probe 0xc00-0xcf7: clean.
[ 28.216940] cs: IO port probe 0xa00-0xaff: clean.
[ 28.589126] loop: module loaded
[ 28.618368] lp0: using parport0 (interrupt-driven).
[ 28.690019] Adding 1012084k swap on /dev/sda3. Priority:-1 extents:1 across:1012084k
[ 28.811621] EXT3 FS on sda2, internal journal
[ 29.502647] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 29.913688] ACPI: ACPI Dock Station Driver
[ 30.039796] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: found ejectable bay
[ 30.039808] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: Adding notify handler
[ 30.039876] ACPI: Error installing bay notify handler
[ 30.039885] ACPI: Bay [\_SB_.PCI0.IDE0.SCND.MSTR] Added
[ 31.124823] NET: Registered protocol family 10
[ 31.125772] lo: Disabled Privacy Extensions
[ 31.292966] IBM machine detected. Enabling interrupts during APM calls.
[ 31.292978] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 31.292982] apm: overridden by ACPI.
[ 31.357539] ppdev: user-space parallel port driver
[ 31.390552] audit(1234319195.542:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=4825 profile="/usr/sbin/cupsd" namespace="default"
[ 31.461979] Non-volatile memory driver v1.2
[ 31.472475] thinkpad_acpi: ThinkPad ACPI Extras v0.17
[ 31.472485] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 31.472489] thinkpad_acpi: ThinkPad BIOS 1AET56WW (1.13 ), EC unknown
[ 31.474820] thinkpad_acpi: another device driver is already handling bay events
[ 31.474830] thinkpad_acpi: disabling subdriver bay
[ 31.476288] input: ThinkPad Extra Buttons as /devices/virtual/input/input8
[ 48.209432] Marking TSC unstable due to: cpufreq changes.
[ 49.804601] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 49.807466] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 49.815867] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 33.243387] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 33.305438] Bluetooth: Core ver 2.11
[ 33.309596] NET: Registered protocol family 31
[ 33.309605] Bluetooth: HCI device and connection manager initialized
[ 33.309613] Bluetooth: HCI socket layer initialized
[ 33.337424] Bluetooth: L2CAP ver 2.9
[ 33.337435] Bluetooth: L2CAP socket layer initialized
[ 33.423925] Bluetooth: RFCOMM socket layer initialized
[ 33.424323] Bluetooth: RFCOMM TTY layer initialized
[ 33.424330] Bluetooth: RFCOMM ver 1.8
[ 33.921994] NET: Registered protocol family 17
[ 35.852437] [drm] Initialized drm 1.1.0 20060810
[ 35.869656] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 35.870316] [drm] Initialized savage 2.4.1 20050313 on minor 0
[ 35.871041] mtrr: base(0xe4000000) is not aligned on a size(0x5000000) boundary
[ 35.871578] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 35.871595] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[ 35.871614] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[ 57.798865] eth0: no IPv6 routers present
[ 77.964428] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 95.128239] wlan0: Initial auth_alg=0
[ 95.128256] wlan0: authenticate with AP 00:1c:df:a8:3a:f5
[ 95.129834] wlan0: RX authentication from 00:1c:df:a8:3a:f5 (alg=0 transaction=2 status=0)
[ 95.129845] wlan0: authenticated
[ 95.129852] wlan0: associate with AP 00:1c:df:a8:3a:f5
[ 95.131063] wlan0: RX AssocResp from 00:1c:df:a8:3a:f5 (capab=0x401 status=0 aid=1)
[ 95.131074] wlan0: associated
[ 95.131157] wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
[ 95.131167] wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
[ 95.131174] wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
[ 95.131182] wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
[ 95.131501] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 96.236213] e100: eth0: e100_watchdog: link down
[ 96.415182] wlan0: no IPv6 routers present
[ 347.091366] wlan0: deauthenticate(reason=3)
[ 347.212296] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 348.602469] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 348.626804] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 352.666360] wlan0: Initial auth_alg=0
[ 352.666376] wlan0: authenticate with AP 00:1c:df:a8:3a:f5
[ 352.667816] wlan0: RX authentication from 00:1c:df:a8:3a:f5 (alg=0 transaction=2 status=0)
[ 352.667828] wlan0: authenticated
[ 352.667835] wlan0: associate with AP 00:1c:df:a8:3a:f5
[ 352.669861] wlan0: RX AssocResp from 00:1c:df:a8:3a:f5 (capab=0x401 status=0 aid=1)
[ 352.669872] wlan0: associated
[ 352.669955] wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
[ 352.669964] wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
[ 352.669972] wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
[ 352.669980] wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
[ 352.670263] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 355.694680] wlan0: no IPv6 routers present
[ 252.065934] wlan0: Initial auth_alg=0
[ 252.065953] wlan0: authenticate with AP 00:1c:df:a8:3a:f5
[ 252.067393] wlan0: RX authentication from 00:1c:df:a8:3a:f5 (alg=0 transaction=2 status=0)
[ 252.067401] wlan0: authenticated
[ 252.067406] wlan0: associate with AP 00:1c:df:a8:3a:f5
[ 252.157373] wlan0: associate with AP 00:1c:df:a8:3a:f5
[ 252.163245] wlan0: associate with AP 00:1c:df:a8:3a:f5
[ 378.258700] wlan0: association with AP 00:1c:df:a8:3a:f5 timed out
[ 378.300521] wlan0: deauthenticate(reason=3)
[ 378.361162] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 252.255038] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 252.289856] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 382.445876] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 285.623307] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 285.664736] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 285.698337] wlan0: Initial auth_alg=0
[ 285.698355] wlan0: authenticate with AP 00:1c:df:a8:3a:f5
[ 285.699797] wlan0: RX authentication from 00:1c:df:a8:3a:f5 (alg=0 transaction=2 status=0)
[ 285.699807] wlan0: authenticated
[ 285.699812] wlan0: associate with AP 00:1c:df:a8:3a:f5
[ 285.701662] wlan0: RX AssocResp from 00:1c:df:a8:3a:f5 (capab=0x401 status=0 aid=1)
[ 285.701674] wlan0: associated
[ 285.701740] wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
[ 285.701747] wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
[ 285.701752] wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
[ 285.701757] wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
[ 285.715857] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 285.717103] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 287.031877] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 295.164421] wlan0: no IPv6 routers present
[ 316.344260] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 317.751884] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 317.806314] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 480.511349] wlan0: Initial auth_alg=0
[ 480.511366] wlan0: authenticate with AP 00:1c:df:a8:3a:f5
[ 480.512476] wlan0: RX authentication from 00:1c:df:a8:3a:f5 (alg=0 transaction=2 status=0)
[ 480.512486] wlan0: authenticated
[ 480.512493] wlan0: associate with AP 00:1c:df:a8:3a:f5
[ 480.513751] wlan0: RX AssocResp from 00:1c:df:a8:3a:f5 (capab=0x401 status=0 aid=1)
[ 480.513764] wlan0: associated
[ 480.513846] wlan0: WMM queue=2 aci=0 acm=0 aifs=3 cWmin=15 cWmax=1023 burst=0
[ 480.513855] wlan0: WMM queue=3 aci=1 acm=0 aifs=7 cWmin=15 cWmax=1023 burst=0
[ 480.513863] wlan0: WMM queue=1 aci=2 acm=0 aifs=2 cWmin=7 cWmax=15 burst=30
[ 480.513871] wlan0: WMM queue=0 aci=3 acm=0 aifs=2 cWmin=3 cWmax=7 burst=15
[ 480.514129] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 483.360201] wlan0: no IPv6 routers present
[ 509.276403] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 509.277012] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 509.400914] wlan0: deauthenticate(reason=3)
[ 512.266959] eth0: no IPv6 routers present
dmesg | grep firmware
Code:
[ 23.323959] IBM TrackPoint firmware: 0x0e, buttons: 3/3
I thought I could get this working on my own, but I guess I still don't have the skill set I thought I had.
Edit: Didn't want to use ndiswrapper if a open source driver was available first.
lspci
Code:
00:00.0 Host bridge: Intel Corporation 82830 830 Chipset Host Bridge (rev 04)
00:01.0 PCI bridge: Intel Corporation 82830 830 Chipset AGP Bridge (rev 04)
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801CA/CAM USB Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801CA/CAM USB Controller #3 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801CA/CAM SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97 Audio Controller (rev 02)
01:00.0 VGA compatible controller: S3 Inc. SuperSavage IX/C SDR (rev 05)
02:00.0 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
02:00.1 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
02:02.0 Communication controller: Agere Systems WinModem 56k (rev 01)
02:08.0 Ethernet controller: Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42)
07:00.0 Network controller: RaLink RT2561/RT61 802.11g PCI
__________________
Free Linux Books
Linux Registered User # 475019
And I’ll keep using Linux until they pry it from my cold dead fingers.
#2 permalink Trusted Penguin
Join Date: Jul 2004
Location: Franklin, Wisconsin
Posts: 3,957
__________________
#3 permalink Linux Guru
Join Date: Jul 2008
Location: Pecos, Texas
Posts: 1,503
Yea I should know how to do this better. I have learned alot from your posts. I think I burned some brain cells on my birthday.
Recent Events since I posted this thread.
Blew away the Xubuntu install on hda2 for now. (30 gig partition)
Booted up Gparted and shrunk 30 gig into 20 gig and 10 gig ext3 partitions.
Booted up Puppy Dingo and connected Belkin card slicker than snot.
Gonna install puppy on the 10 gig partition using full install.
The other 20 gig I haven't decided yet but maybe Xubuntu again or maybe I'll try my hand at Sidux. I'll leave this thread open for now in case you wanna chastise me
but don't forget, I gotta a thick skin so it'll bounce right off.
I'll try to do better next time waterhead. I just get a little fuzzy headed sometimes. HA. Thanks for the response waterhead. If I try Xubuntu again I'll come back to this thread via subscriptions and use your links. happy trails
__________________
Free Linux Books
Linux Registered User # 475019
And I’ll keep using Linux until they pry it from my cold dead fingers.
#4 permalink Trusted Penguin
Join Date: Jul 2004
Location: Franklin, Wisconsin
Posts: 3,957
Hey, I was just yankin' yer chain a little. I see that it worked.
__________________
#5 permalink Linux Guru
Join Date: Jul 2008
Location: Pecos, Texas
Posts: 1,503
Didn't hurt my feelers any waterhead. I seem to be my own worst enemy lately. In fact jerking my chain makes me grin.
__________________
Free Linux Books
Linux Registered User # 475019
And I’ll keep using Linux until they pry it from my cold dead fingers.
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools Display Modes Linear Mode
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
Wireless Internet Anything related to getting wireless set up in Linux. WLAN, WiFi, etc.
Submit Your Article
Latest Articles
Editor's Choice
Article Categories
Join Linux Forums Today
Win Great Prizes
Yea I should know how to do this better. I have learned alot from your posts. I think I burned some brain cells on my birthday.
but don't forget, I gotta a thick skin so it'll bounce right off.
Linear Mode
