Help setting Up Wireless on my Dell Inspiron 1501

[mjr4189]

This si all the information that i got out of terminal after reading this thread
http://www.linuxforums.org/forum/wir...tart-here.html

any help to get my internet working would be awesome!

lspci
00:00.0 Host bridge [0600]: ATI Technologies Inc RS480 Host Bridge [1002:5950] (rev 10)
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f]
00:05.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a37]
00:06.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a38]
00:12.0 SATA controller [0106]: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380]
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI0) [1002:4387]
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI1) [1002:4388]
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI2) [1002:4389]
00:13.3 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI3) [1002:438a]
00:13.4 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI4) [1002:438b]
00:13.5 USB Controller [0c03]: ATI Technologies Inc SB600 USB Controller (EHCI) [1002:4386]
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 14)
00:14.1 IDE interface [0101]: ATI Technologies Inc SB600 IDE [1002:438c]
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB600 PCI to LPC Bridge [1002:438d]
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384]
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS482 [Radeon Xpress 200M] [1002:5975]
05:00.0 Network controller [0280]: Broadcom Corporation BCM4328 802.11a/b/g/n [14e4:4328] (rev 03)
08:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02)
08:01.0 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 19)
08:01.1 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller [1180:0843] (rev 01)


lsmod
Module Size Used by
ip6t_LOG 6212 7
xt_tcpudp 2728 2
xt_pkttype 1560 3
ipt_LOG 5708 8
xt_limit 2056 15
snd_pcm_oss 43300 0
snd_mixer_oss 14288 1 snd_pcm_oss
snd_seq 52248 0
snd_seq_device 7168 1 snd_seq
binfmt_misc 7872 1
ip6t_REJECT 4984 3
nf_conntrack_ipv6 20196 4
ip6table_raw 1792 1
xt_NOTRACK 1544 4
ipt_REJECT 2760 3
xt_state 1904 8
iptable_raw 2056 1
iptable_filter 2548 1
ip6table_mangle 2288 0
nf_conntrack_netbios_ns 2152 0
nf_conntrack_ipv4 10480 4
nf_conntrack 67376 5 nf_conntrack_ipv6,xt_NOTRACK,xt_state,nf_conntrack _netbios_ns,nf_conntrack_ipv4
ip_tables 11260 2 iptable_raw,iptable_filter
ip6table_filter 2408 1
ip6_tables 12476 4 ip6t_LOG,ip6table_raw,ip6table_mangle,ip6table_fil ter
x_tables 14416 11 ip6t_LOG,xt_tcpudp,xt_pkttype,ipt_LOG,xt_limit,ip6 t_REJECT,xt_NOTRACK,ipt_REJECT,xt_state,ip_tables, ip6_tables
ipv6 242864 23 ip6t_REJECT,nf_conntrack_ipv6,ip6table_mangle
cpufreq_conservative 6324 0
cpufreq_userspace 3112 0
cpufreq_powersave 1640 0
powernow_k8 13444 1
loop 15076 0
dm_mod 62236 0
sr_mod 13536 0
cdrom 32288 1 sr_mod
snd_hda_intel 413176 3
ide_pci_generic 3428 0
atiixp 3384 0
snd_pcm 78852 2 snd_pcm_oss,snd_hda_intel
sdhci_pci 7404 0
snd_timer 21132 2 snd_seq,snd_pcm
ide_core 99028 2 ide_pci_generic,atiixp
snd_page_alloc 8048 2 snd_hda_intel,snd_pcm
video 19992 0
snd_hwdep 7144 1 snd_hda_intel
ati_agp 6568 0
sdhci 17276 1 sdhci_pci
b44 26092 0
ata_generic 4484 0
rtc_cmos 11344 0
mii 4968 1 b44
shpchp 28236 0
snd 57408 14 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,s nd_hda_intel,snd_pcm,snd_timer,snd_hwdep
output 2736 1 video
ac 4452 0
ssb 38352 1 b44
rtc_core 18048 1 rtc_cmos
ricoh_mmc 3660 0
dcdbas 8888 0
rtc_lib 2816 1 rtc_core
i2c_piix4 10068 0
agpgart 32408 1 ati_agp
mmc_core 55080 1 sdhci
pci_hotplug 27392 1 shpchp
pcspkr 2344 0
battery 11156 0
pcmcia 32856 1 ssb
pata_atiixp 4560 0
soundcore 6900 1 snd
joydev 9388 0
pcmcia_core 33188 2 ssb,pcmcia
i2c_core 29972 1 i2c_piix4
wmi 6720 0
k8temp 4156 0
button 6560 0
sg 29360 0
ohci_hcd 31536 0
ehci_hcd 47580 0
usbcore 167276 3 ohci_hcd,ehci_hcd
sd_mod 31424 4
crc_t10dif 1704 1 sd_mod
edd 8616 0
ahci 28460 3
libata 160884 3 ata_generic,pata_atiixp,ahci
scsi_mod 149720 4 sr_mod,sg,sd_mod,libata
dock 11988 1 libata
ext3 124684 2
mbcache 8132 1 ext3
jbd 56684 1 ext3
fan 4712 0
thermal 19916 0
processor 43548 2 powernow_k8,thermal
thermal_sys 11364 4 video,fan,thermal,processor
hwmon 3092 2 k8temp,thermal_sys


dmesg
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.27.7-9-default (geeko@buildhost) (gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2008-12-04 18:10:04 +0100
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000077e70000 (usable)
BIOS-e820: 0000000077e70000 - 0000000077e80000 (ACPI data)
BIOS-e820: 0000000077e80000 - 0000000077f00000 (ACPI NVS)
BIOS-e820: 0000000077f00000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
DMI present.
last_pfn = 0x77e70 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
kernel direct mapping tables up to 38000000 @ 7000-c000
RAMDISK: 37a12000 - 37fef48b
ACPI: RSDP 000F8500, 0014 (r0 PTLTD )
ACPI: RSDT 77E79575, 003C (r1 DELL M08 6040000 LTP 0)
ACPI: FACP 77E7FB90, 0074 (r1 ATI Bowfin 6040000 ATI F4240)
ACPI: DSDT 77E795B1, 65DF (r1 ATI SB600 6040000 MSFT 3000000)
ACPI: FACS 77E90FC0, 0040
ACPI: TCPA 77E7FC04, 0032 (r2 AMD 6040000 PTEC 0)
ACPI: SSDT 77E7FC36, 01C4 (r1 PTLTD POWERNOW 6040000 LTP 1)
ACPI: APIC 77E7FDFA, 0054 (r1 PTLTD APIC 6040000 LTP 0)
ACPI: MCFG 77E7FE4E, 003C (r1 PTLTD MCFG 6040000 LTP 0)
ACPI: SLIC 77E7FE8A, 0176 (r1 DELL M08 6040000 LTP 0)
ACPI: DMI detected: Dell i1501
ACPI: Local APIC address 0xfee00000
1022MB HIGHMEM available.
896MB LOWMEM available.
mapped low ram: 0 - 38000000
low ram: 00000000 - 38000000
bootmap 00009000 - 00010000
(9 early reservations) ==> bootmem [0000000000 - 0038000000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 00006509dc] TEXT DATA BSS ==> [0000100000 - 00006509dc]
#4 [0037a12000 - 0037fef48b] RAMDISK ==> [0037a12000 - 0037fef48b]
#5 [0000651000 - 0000654000] INIT_PG_TABLE ==> [0000651000 - 0000654000]
#6 [000009dc00 - 0000100000] BIOS reserved ==> [000009dc00 - 0000100000]
#7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000]
#8 [0000009000 - 0000010000] BOOTMAP ==> [0000009000 - 0000010000]
found SMP MP-table at [c00f8530] 000f8530
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00038000
HighMem 0x00038000 -> 0x00077e70
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009d
0: 0x00000100 -> 0x00077e70
On node 0 totalpages: 491021
free_area_init_node: node 0, pgdat c051ee00, node_mem_map c1000000
DMA zone: 3961 pages, LIFO batch:0
Normal zone: 223300 pages, LIFO batch:31
HighMem zone: 259443 pages, LIFO batch:31
Using APIC driver default
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
PM: Registered nosave memory: 00000000000ce000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
PERCPU: Allocating 39068 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 486704
Kernel command line: root=/dev/disk/by-id/ata-ST9120822AS_5LZ5KLMH-part2 resume=/dev/disk/by-id/ata-ST9120822AS_5LZ5KLMH-part1 splash=silent vga=0x317
bootsplash: silent mode.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PIT calibration value
Detected 1795.488 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1933604k/1964480k available (2342k kernel code, 29676k reserved, 1960k data, 316k init, 1046976k highmem)
virtual kernel memory layout:
fixmap : 0xffdf6000 - 0xfffff000 (2084 kB)
pkmap : 0xff400000 - 0xff800000 (4096 kB)
vmalloc : 0xf8800000 - 0xff3fe000 ( 107 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc053a000 - 0xc0589000 ( 316 kB)
.data : 0xc034988b - 0xc0533a90 (1960 kB)
.text : 0xc0100000 - 0xc034988b (2342 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
Calibrating delay loop (skipped), value calculated using timer frequency.. 3590.97 BogoMIPS (lpj=7181952)
kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reserved
Security Framework initialized
SELinux: Disabled at boot.
AppArmor: AppArmor initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(2) -> Core 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using C1E aware idle routine
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080609
ACPI: Checking initramfs for custom DSDT
Parsing all Control Methods:
Table [DSDT](id 0001) - 819 Objects with 63 Devices 180 Methods 29 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 8 Objects with 0 Devices 0 Methods 0 Regions
tbxface-0596 [00] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 0) ...
....... works.
CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-56 stepping 01
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3591.21 BogoMIPS (lpj=7182426)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1(2) -> Core 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-56 stepping 01
System has AMD C1E enabled
Switch to broadcast mode on CPU0
Brought up 2 CPUs
Total of 2 processors activated (7182.18 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 1 0
Switch to broadcast mode on CPU1
net_namespace: 1044 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 9
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
evgpeblk-0957 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
ACPI: EC: Look up EC in DSDT
Completing Region/Field/Buffer/Package initialization:................................... ...........................................
Initialized 24/29 Regions 0/0 Fields 18/19 Buffers 36/37 Packages (836 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:<5>ACPI: BIOS _OSI(Linux) query ignored via DMI
...
Executed 3 _INI methods requiring 0 _STA executions (examined 68 objects)
evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 5 Wake, Enabled 3 Runtime GPEs in this block
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x14, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
PCI: 0000:00:12.0 reg 10 io port: [8438, 843f]
PCI: 0000:00:12.0 reg 14 io port: [8454, 8457]
PCI: 0000:00:12.0 reg 18 io port: [8430, 8437]
PCI: 0000:00:12.0 reg 1c io port: [8450, 8453]
PCI: 0000:00:12.0 reg 20 io port: [8400, 840f]
PCI: 0000:00:12.0 reg 24 32bit mmio: [c0004000, c00043ff]
pci 0000:00:12.0: set SATA to AHCI mode
PCI: 0000:00:13.0 reg 10 32bit mmio: [c0005000, c0005fff]
PCI: 0000:00:13.1 reg 10 32bit mmio: [c0006000, c0006fff]
PCI: 0000:00:13.2 reg 10 32bit mmio: [c0007000, c0007fff]
PCI: 0000:00:13.3 reg 10 32bit mmio: [c0008000, c0008fff]
PCI: 0000:00:13.4 reg 10 32bit mmio: [c0009000, c0009fff]
PCI: 0000:00:13.5 reg 10 32bit mmio: [c0004400, c00044ff]
pci 0000:00:13.5: supports D1
pci 0000:00:13.5: supports D2
pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.5: PME# disabled
disabled boot interrupts on PCI device 0x1002:0x4385
PCI: 0000:00:14.0 reg 10 io port: [8410, 841f]
PCI: 0000:00:14.0 reg 14 32bit mmio: [c0004800, c0004bff]
PCI: 0000:00:14.1 reg 10 io port: [1f0, 1f7]
PCI: 0000:00:14.1 reg 14 io port: [3f4, 3f7]
PCI: 0000:00:14.1 reg 18 io port: [0, 7]
PCI: 0000:00:14.1 reg 1c io port: [0, 3]
PCI: 0000:00:14.1 reg 20 io port: [8420, 842f]
PCI: 0000:00:14.2 reg 10 64bit mmio: [c0000000, c0003fff]
pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
pci 0000:00:14.2: PME# disabled
PCI: 0000:01:05.0 reg 10 32bit mmio: [c8000000, cfffffff]
PCI: 0000:01:05.0 reg 14 io port: [9000, 90ff]
PCI: 0000:01:05.0 reg 18 32bit mmio: [c0100000, c010ffff]
PCI: 0000:01:05.0 reg 30 32bit mmio: [0, 1ffff]
pci 0000:01:05.0: supports D1
pci 0000:01:05.0: supports D2
PCI: bridge 0000:00:01.0 io port: [9000, 9fff]
PCI: bridge 0000:00:01.0 32bit mmio: [c0100000, c01fffff]
PCI: bridge 0000:00:01.0 64bit mmio pref: [c8000000, cfffffff]
PCI: bridge 0000:00:05.0 io port: [0, fff]
PCI: bridge 0000:00:05.0 32bit mmio: [0, fffff]
PCI: 0000:05:00.0 reg 10 64bit mmio: [c0200000, c0203fff]
PCI: 0000:05:00.0 reg 18 64bit mmio: [d0000000, d00fffff]
pci 0000:05:00.0: supports D1
pci 0000:05:00.0: supports D2
pci 0000:05:00.0: PME# supported from D3hot D3cold
pci 0000:05:00.0: PME# disabled
PCI: bridge 0000:00:06.0 32bit mmio: [c0200000, c02fffff]
PCI: bridge 0000:00:06.0 64bit mmio pref: [d0000000, d00fffff]
PCI: 0000:08:00.0 reg 10 32bit mmio: [c0300000, c0301fff]
pci 0000:08:00.0: supports D1
pci 0000:08:00.0: supports D2
pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:08:00.0: PME# disabled
PCI: 0000:08:01.0 reg 10 32bit mmio: [c0302800, c03028ff]
pci 0000:08:01.0: supports D1
pci 0000:08:01.0: supports D2
pci 0000:08:01.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:08:01.0: PME# disabled
PCI: 0000:08:01.1 reg 10 32bit mmio: [c0302c00, c0302cff]
pci 0000:08:01.1: supports D1
pci 0000:08:01.1: supports D2
pci 0000:08:01.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:08:01.1: PME# disabled
pci 0000:00:14.4: transparent bridge
PCI: bridge 0000:00:14.4 32bit mmio: [c0300000, c03fffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:08: io resource (0x22-0x23) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x2e-0x2f) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x72-0x73) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x68-0x6f) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xb0-0xb1) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x92-0x92) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x220-0x22f) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x40b-0x40b) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x4d0-0x4d1) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x4d6-0x4d6) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x530-0x537) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xc00-0xc01) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xc14-0xc14) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xc50-0xc52) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xc6c-0xc6c) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xc6f-0xc6f) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xcd0-0xcd3) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xcd4-0xcd5) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xcd6-0xcd7) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xcd8-0xcdf) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0xf40-0xf47) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:08: io resource (0x87f-0x87f) overlaps 0000:00:05.0 BAR 7 (0x0-0xfff), disabling
pnp 00:09: mem resource (0xe0000-0xfffff) overlaps 0000:00:05.0 BAR 8 (0x0-0xfffff), disabling
pnp 00:09: mem resource (0x0-0xfff) overlaps 0000:00:05.0 BAR 8 (0x0-0xfffff), disabling
pnp 00:09: mem resource (0x0-0xfff) overlaps 0000:01:05.0 BAR 6 (0x0-0x1ffff), disabling
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
pci 0000:00:05.0: BAR 7: can't allocate resource
pci 0000:00:05.0: BAR 8: can't allocate resource
AppArmor: AppArmor Filesystem Enabled
ACPI Error (exresop-0103): Needed type [Reference], found [Device] f7430d88 [20080609]
ACPI Exception (dswexec-0441): AE_AML_OPERAND_TYPE, While resolving operands for [Unload] [20080609]
ACPI Error (psparse-0530): Method parse/execution failed [\_SB_.PCI0._OSC] (Node f7451d74), AE_AML_OPERAND_TYPE
ACPI: RTC can wake from S4
system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:08: ioport range 0x1080-0x1080 has been reserved
system 00:08: ioport range 0x8000-0x805f has been reserved
system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
system 00:09: iomem range 0xc0004800-0xc0004bff has been reserved
system 00:09: iomem range 0xfed00000-0xfed003ff has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x9000-0x9fff
pci 0000:00:01.0: MEM window: 0xc0100000-0xc01fffff
pci 0000:00:01.0: PREFETCH window: 0x000000c8000000-0x000000cfffffff
pci 0000:00:05.0: PCI bridge, secondary bus 0000:02
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:05
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: 0xc0200000-0xc02fffff
pci 0000:00:06.0: PREFETCH window: 0x000000d0000000-0x000000d00fffff
pci 0000:00:14.4: PCI bridge, secondary bus 0000:08
pci 0000:00:14.4: IO window: disabled
pci 0000:00:14.4: MEM window: 0xc0300000-0xc03fffff
pci 0000:00:14.4: PREFETCH window: disabled
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffff]
bus: 01 index 0 io port: [9000, 9fff]
bus: 01 index 1 mmio: [c0100000, c01fffff]
bus: 01 index 2 mmio: [c8000000, cfffffff]
bus: 01 index 3 mmio: [0, 0]
bus: 02 index 0 mmio: [0, fff]
bus: 02 index 1 mmio: [0, fffff]
bus: 02 index 2 mmio: [0, 0]
bus: 02 index 3 mmio: [0, 0]
bus: 05 index 0 mmio: [0, 0]
bus: 05 index 1 mmio: [c0200000, c02fffff]
bus: 05 index 2 mmio: [d0000000, d00fffff]
bus: 05 index 3 mmio: [0, 0]
bus: 08 index 0 mmio: [0, 0]
bus: 08 index 1 mmio: [c0300000, c03fffff]
bus: 08 index 2 mmio: [0, 0]
bus: 08 index 3 io port: [0, ffff]
bus: 08 index 4 mmio: [0, ffffffff]
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 6005k freed
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
type=2000 audit(1238629461.680:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 436
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:00.0: MSI quirk detected; MSI disabled
pci 0000:01:05.0: Boot video device
pcieport-driver 0000:00:05.0: setting latency timer to 64
pcieport-driver 0000:00:05.0: found MSI capability
pci_express 0000:00:05.0cie00: allocate port service
pci_express 0000:00:05.0cie02: allocate port service
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: found MSI capability
pci_express 0000:00:06.0cie00: allocate port service
pci_express 0000:00:06.0cie02: allocate port service
vesafb: framebuffer at 0xc8000000, mapped to 0xf8880000, using 6144k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:51a0
vesafb: pmi: set display start = c00c5234, set palette = c00c5280
vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 100719 bytes
bootsplash: ...found (1024x768, 38691 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver8 ports, IRQ sharing enabled
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 316k freed
Write protecting the kernel text: 2344k
Write protecting the kernel read-only data: 1768k
ACPI: processor limited to max C-state 1
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
processor ACPI_CPU:01: registered as cooling_device1
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (35 C)
ACPI: No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:12.0: version 3.0
ahci 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 irq_stat 0x00400040 irq 22, connection status changed
ata2: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004180 irq 22
ata3: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004200 irq 22
ata4: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004280 irq 22
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x180b1, caps: 0xa04713/0x200000
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input1
ata1: softreset failed (device not ready)
ata1: failed due to HW bug, retry pmp=0
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: ST9120822AS, 3.CDD, max UDMA/133
ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA ST9120822AS 3.CD PQ: 0 ANSI: 5
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
udevd version 128 started
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120GB/111GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120GB/111GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<6>usbcore: registered new interface driver usbfs
sda1 sda2 sda3
usbcore: registered new interface driver hub
sd 0:0:0:0: [sda] Attached SCSI disk
usbcore: registered new device driver usb
ehci_hcd 0000:00:13.5: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 19, io mem 0xc0004400
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27.7-9-default ehci_hcd
usb usb1: SerialNumber: 0000:00:13.5
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 16, io mem 0xc0005000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27.7-9-default ohci_hcd
usb usb2: SerialNumber: 0000:00:13.0
ohci_hcd 0000:00:13.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 17, io mem 0xc0006000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27.7-9-default ohci_hcd
usb usb3: SerialNumber: 0000:00:13.1
ohci_hcd 0000:00:13.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.2: irq 18, io mem 0xc0007000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27.7-9-default ohci_hcd
usb usb4: SerialNumber: 0000:00:13.2
ohci_hcd 0000:00:13.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.3: irq 17, io mem 0xc0008000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27.7-9-default ohci_hcd
usb usb5: SerialNumber: 0000:00:13.3
ohci_hcd 0000:00:13.4: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.4: irq 18, io mem 0xc0009000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.27.7-9-default ohci_hcd
usb usb6: SerialNumber: 0000:00:13.4
PM: Starting manual resume from disk
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 128 started
sd 0:0:0:0: Attached scsi generic sg0 type 0
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pata_atiixp 0000:00:14.1: setting latency timer to 64
scsi4 : pata_atiixp
scsi5 : pata_atiixp
ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8420 irq 14
ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8428 irq 15
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
ACPI: Sleep Button (CM) [SLPB]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input5
input: PC Speaker as /devices/platform/pcspkr/input/input6
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Lid Switch [LID]
ACPI: WMI: Mapper loaded
ata5.00: ATAPI: TSSTcorpCD-RW/DVD-ROM TSL462D, DE04, max UDMA/33
ata5.00: configured for UDMA/33
Linux agpgart interface v0.103
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
scsi 4:0:0:0: CD-ROM TSSTcorp CDRW/DVD TSL462D DE04 PQ: 0 ANSI: 5
scsi 4:0:0:0: Attached scsi generic sg1 type 5
piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x8410, revision 0
ricoh-mmc: Ricoh MMC controller found at 0000:08:01.1 [1180:0843] (rev 1)
ricoh-mmc: Main firewire function not found. Cannot disable controller.
vendor=1002 device=5a38
b43-pci-bridge 0000:05:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
b43-pci-bridge 0000:05:00.0: setting latency timer to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ACAD] (on-line)
vendor=1002 device=4384
b44 0000:08:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
acpi device:1e: registered as cooling_device2
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:1b/device:1c/input/input7
Uniform Multi-Platform E-IDE driver
ssb: Sonics Silicon Backplane found on PCI device 0000:08:00.0
b44.c:v2.0
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:1c:23:88:bc:37
sdhci-pci 0000:08:01.0: SDHCI controller found [1180:0822] (rev 19)
vendor=1002 device=4384
sdhci-pci 0000:08:01.0: PCI INT B -> GSI 20 (level, low) -> IRQ 20
mmc0: SDHCI controller on PCI [0000:08:01.0] using PIO
HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ALSA sound/pci/hda/hda_codec.c:3047: autoconfig: line_outs=1 (0xe/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3051: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3055: hp_outs=1 (0xd/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3056: mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:3064: inputs: mic=0x10, fmic=0x0, line=0x0, fline=0x0, cd=0x0, aux=0x0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
Adding 2104472k swap on /dev/sda1. Priority:-1 extents:1 across:2104472k
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-56 processors (2 cpu cores) (version 2.20.00)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x12
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x13
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1e
Clocksource tsc unstable (delta = -199132246 ns)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
pci 0000:01:05.0: power state changed by ACPI to D0
vendor=1002 device=5a3f
pci 0000:01:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
bootsplash: status on console 0 changed to on
ADDRCONF(NETDEV_UP): eth0: link is not ready
CPU0 attaching NULL sched-domain.
CPU1 attaching NULL sched-domain.
CPU0 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level CPU
groups: 1 0
hda-intel: Invalid position buffer, using LPIB read method instead.

uname
2.6.27.7-9-default

[techieMoe]

You have a Broadcom BCM4328 according to the information presented. Here's an article for that wireless chipset using Ubuntu 7.10, but the instructions should work for any distro. Basically you need a copy of the Windows XP drivers for the card (should be available on the Dell website) and a program called NDISWrapper.

Getting Dell BCM4328 Wifi Card Working on Ubuntu 7.10

[mjr4189]

Alright awesome, thanks a lot i will try that and come back to mark the thread solved if it works out.

[mjr4189]

ok, i did all of that but still cant find out how to connect to a network....
My windows drive ris installed and i modprobed and that stuff but now im just sitting with an installed driver and a network manager that doesn't see networks....

[techieMoe]

ok, i did all of that but still cant find out how to connect to a network....
My windows drive ris installed and i modprobed and that stuff but now im just sitting with an installed driver and a network manager that doesn't see networks....

Did you reboot?

[mjr4189]

Did you reboot?

of course, lol. i just don't know how to find a network.

[techieMoe]

of course, lol. i just don't know how to find a network.

You laugh, but I've spent quite a while diagnosing problems that were that simple. What distribution of Linux are you using?

[mjr4189]

I'm running Opensuse 11.1.

[waterhead]

In SuSE you will then need to configure the card using YaST. Try this:

Open YaST from main menu:
Computer -->YaST
Network Devices-->Network Settings

On the "Global options" tab, make sure that this is selected:
User Controlled with NetworkManager

Now click the "Overview" tab. Click on the wireless device, in the list, to highlight it. Then click the "Edit" button at the bottom. On the "Hardware" tab, click on the "Select Module Name" dropdown box. If the ndiswrapper module is loaded, it should be an option.

In the "Address" tab, select --> Dynamic Address: DHCP
from the dropdown box. Save the configuration and maybe reboot. Make sure that the ndiswrapper is loading at boot using the lsmod command, and the wireless should work.

[mjr4189]

Alright well sorry to say but i bailed on opensuse, i really liked it but a friend of mine mentioned to me that for some odd reason Ubuntu/Kubutnu 8.04 both support my Broadcom BCM4328 Wireless card right out of the box. It is a very weird but i went into the live CD for each and sure enough i could connect to the networks without using NDISWRAPPER or any other back door fixes.
Another thing i noticed is that the 8.10 versions of both of those distros does not work the same way. For some reason or another 8.04 just works with my card although absolutely no other distro would.
Does anyone know why this could possibly happen, and what could have been changed in the 8.10 versions in order to stop this from working?