dandare

I have tried to get my wireless connection to work but as no success ..here is the info i have ...

lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [8086:2590] (rev 03)
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 03)
00:02.1 Display controller [0380]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller [8086:2668] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03)
00:1c.3 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 [8086:2666] (rev 03)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 03)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 03)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 03)
00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 03)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev d3)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge [8086:2641] (rev 03)
00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller [8086:266f] (rev 03)
02:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02)
02:03.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
linux-dnpm:/home/joe # lsmod
Module Size Used by
sco 9600 2
bridge 47772 1
stp 2248 1 bridge
bnep 11548 2
rfcomm 34448 0
l2cap 19828 6 bnep,rfcomm
bluetooth 52800 6 sco,bnep,rfcomm,l2cap
binfmt_misc 7732 1
snd_pcm_oss 43024 0
snd_mixer_oss 14288 1 snd_pcm_oss
snd_seq 51924 0
snd_seq_device 7168 1 snd_seq
i915 27836 2
drm 74604 3 i915
af_packet 16412 2
ndiswrapper 177732 0
fuse 50596 5
loop 14064 0
dm_mod 62588 0
rtc_cmos 10896 0
rtc_core 17384 1 rtc_cmos
dcdbas 8932 0
rtc_lib 2816 1 rtc_core
video 20308 0
output 2736 1 video
b44 25968 0
ssb 38396 1 b44
pcmcia 32684 1 ssb
pcmcia_core 33164 2 ssb,pcmcia
mii 4968 1 b44
snd_hda_intel 416844 3
snd_pcm 76900 2 snd_pcm_oss,snd_hda_intel
button 6568 0
iTCO_wdt 10016 0
snd_timer 20204 2 snd_seq,snd_pcm
iTCO_vendor_support 3368 1 iTCO_wdt
snd_page_alloc 8184 2 snd_hda_intel,snd_pcm
battery 11176 0
snd_hwdep 7144 1 snd_hda_intel
ac 4480 0
snd 56816 14 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,s nd_hda_intel,snd_pcm,snd_timer,snd_hwdep
intel_agp 24776 1
pcspkr 2344 0
sr_mod 13360 1
joydev 8944 0
soundcore 6660 1 snd
agpgart 32308 3 drm,intel_agp
cdrom 32292 1 sr_mod
sg 29408 0
sd_mod 31624 5
crc_t10dif 1704 1 sd_mod
ehci_hcd 47732 0
uhci_hcd 23072 0
usbcore 165892 4 ndiswrapper,ehci_hcd,uhci_hcd
edd 8616 0
ext3 123932 2
mbcache 7592 1 ext3
jbd 52872 1 ext3
fan 4712 0
ide_pci_generic 3428 0
piix 5868 0
ide_core 97492 2 ide_pci_generic,piix
ata_generic 4484 0
ata_piix 16652 5
libata 160812 2 ata_generic,ata_piix
scsi_mod 149672 4 sr_mod,sg,sd_mod,libata
dock 11804 1 libata
thermal 19976 0
processor 43644 2 thermal
thermal_sys 11364 4 video,fan,thermal,processor
hwmon 2916 1 thermal_sys
linux-dnpm:/home/joe #

lsmod
Module Size Used by
sco 9600 2
bridge 47772 1
stp 2248 1 bridge
bnep 11548 2
rfcomm 34448 0
l2cap 19828 6 bnep,rfcomm
bluetooth 52800 6 sco,bnep,rfcomm,l2cap
binfmt_misc 7732 1
snd_pcm_oss 43024 0
snd_mixer_oss 14288 1 snd_pcm_oss
snd_seq 51924 0
snd_seq_device 7168 1 snd_seq
i915 27836 2
drm 74604 3 i915
af_packet 16412 2
ndiswrapper 177732 0
fuse 50596 5
loop 14064 0
dm_mod 62588 0
rtc_cmos 10896 0
rtc_core 17384 1 rtc_cmos
dcdbas 8932 0
rtc_lib 2816 1 rtc_core
video 20308 0
output 2736 1 video
b44 25968 0
ssb 38396 1 b44
pcmcia 32684 1 ssb
pcmcia_core 33164 2 ssb,pcmcia
mii 4968 1 b44
snd_hda_intel 416844 3
snd_pcm 76900 2 snd_pcm_oss,snd_hda_intel
button 6568 0
iTCO_wdt 10016 0
snd_timer 20204 2 snd_seq,snd_pcm
iTCO_vendor_support 3368 1 iTCO_wdt
snd_page_alloc 8184 2 snd_hda_intel,snd_pcm
battery 11176 0
snd_hwdep 7144 1 snd_hda_intel
ac 4480 0
snd 56816 14 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,s nd_hda_intel,snd_pcm,snd_timer,snd_hwdep
intel_agp 24776 1
pcspkr 2344 0
sr_mod 13360 0
joydev 8944 0
soundcore 6660 1 snd
agpgart 32308 3 drm,intel_agp
cdrom 32292 1 sr_mod
sg 29408 0
sd_mod 31624 5
crc_t10dif 1704 1 sd_mod
ehci_hcd 47732 0
uhci_hcd 23072 0
usbcore 165892 4 ndiswrapper,ehci_hcd,uhci_hcd
edd 8616 0
ext3 123932 2
mbcache 7592 1 ext3
jbd 52872 1 ext3
fan 4712 0
ide_pci_generic 3428 0
piix 5868 0
ide_core 97492 2 ide_pci_generic,piix
ata_generic 4484 0
ata_piix 16652 4
libata 160812 2 ata_generic,ata_piix
scsi_mod 149672 4 sr_mod,sg,sd_mod,libata
dock 11804 1 libata
thermal 19976 0
processor 43644 2 thermal
thermal_sys 11364 4 video,fan,thermal,processor
hwmon 2916 1 thermal_sys
linux-dnpm:/home/joe #

dmesg | grep firmware
linux-dnpm:/home/joe #

uname -r
2.6.27.21-0.1-pae

Open Suse 11.1

waterhead

Your wireless only needed firmware installed for it to work, which can be done with this command.
BUT, it requires the b43 driver module, which I don't see loaded. What I do see is NDISwrapper loading, so you must have followed some NDISwrapper instructions that told you to blacklist the b43 module.

I recommend uninstalling NDISwrapper, removing b43 from the blacklist file and add ndiswrapper to it instead, and install the firmware with the above command.

You then should configure it in YaST as a new network card.

__________________
Paul

Please do not PM me with requests for help. I will not reply.

dandare

now have a connection ..the gui says connected ..but www will not load any pages even with ip address

have tried different configurations in Network Settings .using no security wep and also wpa psk etc .firewall is off

sudo /usr/sbin/install_instbcm43xx_firmware
installed

uninstalled ndiswrapper in yast/software/software management

added ndiswrapper to blacklist


here is the output from commands ....

linux-dnpm:/home/joe #
lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03)
02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)







firmware: requesting b43/ucode5.fw
firmware: requesting b43/pcm5.fw
firmware: requesting b43/b0g0initvals5.fw
firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
wlan0: authenticate with AP 00:1e:74:87:c1:5a
wlan0: authenticated
wlan0: associate with AP 00:1e:74:87:c1:5a
wlan0: RX AssocResp from 00:1e:74:87:c1:5a (capab=0x411 status=0 aid=1)
wlan0: associated
bootsplash: status on console 0 changed to on
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.10
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.01: ST_FIRST: !(DRQ|ERR|DF)
ata1.01: cmd a0/00:00:00:00:00/00:00:00:00:00/b0 tag 0
cdb 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
res 50/00:01:00:00:00/00:00:00:00:00/b0 Emask 0x2 (HSM violation)
ata1.01: status: { DRDY }
ata1: soft resetting link
ata1: clearing spurious IRQ
ata1: clearing spurious IRQ
ata1: clearing spurious IRQ
ata1: clearing spurious IRQ
ata1.00: configured for UDMA/100
ata1: clearing spurious IRQ
ata1: clearing spurious IRQ
ata1.01: configured for UDMA/33
ata1: EH complete
sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: (60.0GB/55.8GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: (60.0GB/55.8GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[drm:i915_getparam] *ERROR* Unknown parameter 5
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
linux-dnpm:/home/joe #

linux-dnpm:/home/joe # dmesg | grep firmware
firmware: requesting b43/ucode5.fw
firmware: requesting b43/pcm5.fw
firmware: requesting b43/b0g0initvals5.fw
firmware: requesting b43/b0g0bsinitvals5.fw
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)

linux-dnpm:/home/joe # uname -r
2.6.27.21-0.1-pae

linux-dnpm:/home/joe # iwconfig
lo no wireless extensions.

wmaster0 no wireless extensions.

wlan0 IEEE 802.11bg ESSID:"SKY49497"
Mode:Managed Frequency:2.437 GHz Access Point: 00:1E:74:87:C1:5A
Bit Rate=54 Mb/s Tx-Power=27 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:9BE0-797D-1388-68A1-8028-1625-587B-2DDC-1CE0-C949-DBE8-717A-677A-8BDA-3254-FDBA [2] Security mode:open
Power Management:off
Link Quality=60/100 Signal level:-50 dBm Noise level=-72 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

eth0 no wireless extensions.

pan0 no wireless extensions.

thanks

waterhead

You may need to provide the IP address of the router. There should be a place in the YaST network configuration for that, most likely it is called the Default Gateway.

__________________
Paul

Please do not PM me with requests for help. I will not reply.