Find the answer to your Linux question:
Page 4 of 5 FirstFirst 1 2 3 4 5 LastLast
Results 31 to 40 of 43
But does Wicd work? Can you connect with it? I assume that you may have rebooted since the last time. Remember I had you manually load the module (modprobe rt73usb)? ...
Enjoy an ad free experience by logging in. Not a member yet? Register.
  1. #31
    Linux Guru
    Join Date
    Jul 2004
    Posts
    4,593

    But does Wicd work? Can you connect with it?

    I assume that you may have rebooted since the last time. Remember I had you manually load the module (modprobe rt73usb)? Even though it didn't appear to do anything, maybe it did load the correct module. Manually loaded modules will not automatically load again after a reboot.

    Since there are actually two modules that are trying to use this card, I want you to first remove them both, then load just the one.
    Code:
    sudo modprobe -r rt73usb
    Code:
    sudo modprobe -r rt2500usb
    Now load the module that you want to try.
    Code:
    sudo modprobe rt73usb
    If that doesn't help, try doing it again, but this time load the rt2500usb module instead of the rt73usb module. If that still doesn't work, then just do what you originally did. Reboot, and then just load the rt73usb module.

    I wanted you to do this in order to isolate the module that is needed for your wireless. We can then have that one automatically load, and prevent the one that is not needed from loading.

    But first we need to get it to work!
    Please do not send Private Messages to me with requests for help. I will not reply.

  2. #32
    Linux Enthusiast cousinlucky's Avatar
    Join Date
    Dec 2005
    Location
    New York City
    Posts
    676
    Waterhead I do not know if this worked or not.

    cousinlucky@cousinlucky-desktop:~$ sudo modprobe rt73usb
    cousinlucky@cousinlucky-desktop:~$

    I have to go back and see what the command was to check if the adapter is working. Wicd says no wireless found.

    dmesg

    [ 1733.336126] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 1739.180076] PPP BSD Compression module registered
    [ 1739.257857] PPP Deflate Compression module registered
    [ 1739.329913] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 2003.056537] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 2006.697023] usbcore: registered new interface driver rt73usb
    [ 2009.050333] ACPI: Unable to turn cooling device [d9d62f18] 'on'


    [ 2230.824440] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 2232.212770] usblp0: removed
    [ 2232.709489] audit(1240424122.807:3): type=1503 operation="inode_permission" requested_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=13591 profile="/usr/sbin/cupsd" namespace="default"
    [ 2236.818236] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 2320.731235] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 2322.392893] usb 5-8: new high speed USB device using ehci_hcd and address 5
    [ 2322.663637] usb 5-8: configuration #1 chosen from 1 choice
    [ 2322.927116] phy0: Selected rate control algorithm 'simple'
    [ 2322.998120] usbcore: registered new interface driver rt2500usb
    [ 2326.725022] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 2686.352239] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 2687.186429] usb 5-8: USB disconnect, address 5
    [ 2692.346023] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 2920.109921] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 2921.603750] usb 5-8: new high speed USB device using ehci_hcd and address 6
    [ 2921.874921] usb 5-8: configuration #1 chosen from 1 choice
    [ 2922.140104] phy1: Selected rate control algorithm 'simple'
    [ 2926.103711] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 2932.097496] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    cousinlucky@cousinlucky-desktop:~$
    PCLinuxOS Gnome and PCLinuxOS Mate
    Linux user # 414321
    You Should Not Give In To Evils, But Proceed Ever More Boldly Against Them!! -from book six of Virgil's Aeneid
    Everything Within The Universe Is Related; We Are All Cousins!!

  3. #33
    Linux Guru
    Join Date
    Jul 2004
    Posts
    4,593
    I always have to hit the "Refresh" button before Wicd will see my network.
    Please do not send Private Messages to me with requests for help. I will not reply.

  4. #34
    Linux Guru
    Join Date
    Jul 2004
    Posts
    4,593
    To scan using a terminal command, use this:
    Code:
    iwlist wlan0 scan
    If it gives you nothing, Then try the rt2500usb module (alone).
    Code:
    sudo modprobe -r rt2500usb
    Code:
    sudo modprobe -r rt73usb
    Code:
    sudo modprobe rt2500usb
    If still no luck, then remove them both, and load them both together.
    Code:
    sudo modprobe -r rt73usb
    Code:
    sudo modprobe -r rt2500usb
    Code:
    sudo modprobe rt73usb
    Code:
    sudo modprobe rt2500usb
    It seemed to work before (using the iwlist scan command), so we should be able to get it back to that state.
    Please do not send Private Messages to me with requests for help. I will not reply.

  5. #35
    Linux Enthusiast cousinlucky's Avatar
    Join Date
    Dec 2005
    Location
    New York City
    Posts
    676
    I did everything specified; here is the new dmesg minus the cooling fan notices.

    [ 23.439712] Freeing initrd memory: 7700k freed
    [ 23.440407] audit: initializing netlink socket (disabled)
    [ 23.440426] audit(1240438951.308:1): initialized
    [ 23.442286] VFS: Disk quotas dquot_6.5.1
    [ 23.442317] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 23.442462] io scheduler noop registered
    [ 23.442465] io scheduler anticipatory registered
    [ 23.442467] io scheduler deadline registered
    [ 23.442476] io scheduler cfq registered (default)
    [ 23.442488] PCI: VIA PCI bridge detected. Disabling DAC.
    [ 23.442551] PCI: Bypassing VIA 8237 APIC De-Assert Message
    [ 23.442561] Boot video device is 0000:01:00.0
    [ 23.442833] isapnp: Scanning for PnP cards...
    [ 23.796404] isapnp: No Plug & Play device found
    [ 23.824394] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    [ 23.824520] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 23.825264] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 23.826006] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
    [ 23.826077] input: Macintosh mouse button emulation as /devices/virtual/input/input0
    [ 23.826171] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [ 23.826550] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 23.826555] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 23.829224] mice: PS/2 mouse device common for all mice
    [ 23.829337] EISA: Probing bus 0 at eisa.0
    [ 23.829356] Cannot allocate resource for EISA slot 4
    [ 23.829358] Cannot allocate resource for EISA slot 5
    [ 23.829370] EISA: Detected 0 cards.
    [ 23.829373] cpuidle: using governor ladder
    [ 23.829521] NET: Registered protocol family 1
    [ 23.829549] Using IPI Shortcut mode
    [ 23.829585] registered taskstats version 1
    [ 23.829698] Magic number: 5:797:401
    [ 23.829958] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
    [ 23.829960] EDD information not available.
    [ 23.830481] Freeing unused kernel memory: 364k freed
    [ 23.830511] Write protecting the kernel read-only data: 787k
    [ 23.864734] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
    [ 25.030457] fuse init (API version 7.9)
    [ 25.044436] ACPI: Fan [FAN] (on)
    [ 25.052057] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 25.052065] ACPI: Thermal Zone [THRM] (44 C)
    [ 25.576765] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 19 (level, low) -> IRQ 16
    [ 25.629502] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[ea011000-ea0117ff] Max Packet=[2048] IR/IT contexts=[4/8]
    [ 25.662003] SCSI subsystem initialized
    [ 25.710920] usbcore: registered new interface driver usbfs
    [ 25.710950] usbcore: registered new interface driver hub
    [ 25.720231] libata version 3.00 loaded.
    [ 25.732500] usbcore: registered new device driver usb
    [ 25.733576] USB Universal Host Controller Interface driver v3.0
    [ 25.762807] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
    [ 25.813501] sata_via 0000:00:0f.0: version 2.3
    [ 25.813827] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
    [ 25.813831] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
    [ 25.813841] ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 17
    [ 25.813914] sata_via 0000:00:0f.0: routed to hard irq line 11
    [ 25.814958] scsi0 : sata_via
    [ 25.816179] scsi1 : sata_via
    [ 25.817350] ata1: SATA max UDMA/133 cmd 0xb000 ctl 0xb400 bmdma 0xc000 irq 17
    [ 25.817354] ata2: SATA max UDMA/133 cmd 0xb800 ctl 0xbc00 bmdma 0xc008 irq 17
    [ 25.890677] Floppy drive(s): fd0 is 1.44M
    [ 25.914494] FDC 0 is a post-1991 82077
    [ 26.018548] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
    [ 26.230275] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
    [ 26.243025] pata_via 0000:00:0f.1: version 0.3.3
    [ 26.243071] ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 17
    [ 26.244471] scsi2 : pata_via
    [ 26.245090] scsi3 : pata_via
    [ 26.246412] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xc800 irq 14
    [ 26.246415] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xc808 irq 15
    [ 26.466533] ata3.00: ATA-6: ST3160021A, 3.06, max UDMA/100
    [ 26.466539] ata3.00: 312581808 sectors, multi 16: LBA48
    [ 26.482354] ata3.00: configured for UDMA/100
    [ 26.965851] ata4.00: ATAPI: Hewlett-Packard DVD Writer 300, 3.11, max UDMA/33
    [ 26.965871] ata4.01: ATAPI: SAMSUNG CD-ROM SC-148A, B401, max UDMA/33
    [ 27.081496] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e0180000d03ed0]
    [ 27.137552] ata4.00: configured for UDMA/33
    [ 27.309334] ata4.01: configured for UDMA/33
    [ 27.309469] scsi 2:0:0:0: Direct-Access ATA ST3160021A 3.06 PQ: 0 ANSI: 5
    [ 27.312088] scsi 3:0:0:0: CD-ROM HP DVD Writer 300n 3.11 PQ: 0 ANSI: 5
    [ 27.312431] scsi 3:0:1:0: CD-ROM SAMSUNG CD-ROM SC-148A B401 PQ: 0 ANSI: 5
    [ 27.313725] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
    [ 27.313729] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
    [ 27.313738] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
    [ 27.313752] uhci_hcd 0000:00:10.0: UHCI Host Controller
    [ 27.314111] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
    [ 27.314142] uhci_hcd 0000:00:10.0: irq 18, io base 0x0000cc00
    [ 27.314293] usb usb1: configuration #1 chosen from 1 choice
    [ 27.314319] hub 1-0:1.0: USB hub found
    [ 27.314326] hub 1-0:1.0: 2 ports detected
    [ 27.417170] ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
    [ 27.417187] uhci_hcd 0000:00:10.1: UHCI Host Controller
    [ 27.417213] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
    [ 27.417237] uhci_hcd 0000:00:10.1: irq 18, io base 0x0000d000
    [ 27.417374] usb usb2: configuration #1 chosen from 1 choice
    [ 27.417398] hub 2-0:1.0: USB hub found
    [ 27.417406] hub 2-0:1.0: 2 ports detected
    [ 27.521046] ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
    [ 27.521060] uhci_hcd 0000:00:10.2: UHCI Host Controller
    [ 27.521089] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
    [ 27.521111] uhci_hcd 0000:00:10.2: irq 18, io base 0x0000d400
    [ 27.521225] usb usb3: configuration #1 chosen from 1 choice
    [ 27.521248] hub 3-0:1.0: USB hub found
    [ 27.521254] hub 3-0:1.0: 2 ports detected
    [ 27.624928] ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
    [ 27.624941] uhci_hcd 0000:00:10.3: UHCI Host Controller
    [ 27.624969] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
    [ 27.624990] uhci_hcd 0000:00:10.3: irq 18, io base 0x0000d800
    [ 27.625102] usb usb4: configuration #1 chosen from 1 choice
    [ 27.625126] hub 4-0:1.0: USB hub found
    [ 27.625132] hub 4-0:1.0: 2 ports detected
    [ 27.656787] usb 1-1: new full speed USB device using uhci_hcd and address 2
    [ 27.729217] ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 18
    [ 27.729233] ehci_hcd 0000:00:10.4: EHCI Host Controller
    [ 27.729265] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
    [ 27.729313] ehci_hcd 0000:00:10.4: irq 18, io mem 0xea012000
    [ 27.780678] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
    [ 27.780825] usb usb5: configuration #1 chosen from 1 choice
    [ 27.780853] hub 5-0:1.0: USB hub found
    [ 27.780862] hub 5-0:1.0: 8 ports detected
    [ 27.885275] ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 23
    [ 27.885280] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
    [ 27.885290] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 19
    [ 27.885548] eth0: VIA Rhine II at 0xea013000, 00:0e:a6:d0:6f:01, IRQ 19.
    [ 27.886260] eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
    [ 27.897037] Driver 'sd' needs updating - please use bus_type methods
    [ 27.897158] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
    [ 27.897174] sd 2:0:0:0: [sda] Write Protect is off
    [ 27.897176] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 27.897195] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 27.897247] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
    [ 27.897257] sd 2:0:0:0: [sda] Write Protect is off
    [ 27.897259] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 27.897273] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 27.897277] sda:<4>Driver 'sr' needs updating - please use bus_type methods
    [ 27.907333] sda1 sda2 < sda5 > sda3
    [ 27.927020] sd 2:0:0:0: [sda] Attached SCSI disk
    [ 27.932124] sd 2:0:0:0: Attached scsi generic sg0 type 0
    [ 27.932148] sr 3:0:0:0: Attached scsi generic sg1 type 5
    [ 27.932167] scsi 3:0:1:0: Attached scsi generic sg2 type 5
    [ 27.936904] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
    [ 27.936913] Uniform CD-ROM driver Revision: 3.20
    [ 27.936989] sr 3:0:0:0: Attached scsi CD-ROM sr0
    [ 27.941239] sr1: scsi3-mmc drive: 1x/48x cd/rw xa/form2 cdda tray
    [ 27.941302] sr 3:0:1:0: Attached scsi CD-ROM sr1
    [ 28.176247] usb 1-1: device not accepting address 2, error -71
    [ 28.308192] Attempting manual resume
    [ 28.308197] swsusp: Resume From Partition 8:5
    [ 28.308199] PM: Checking swsusp image.
    [ 28.308411] PM: Resume from disk failed.
    [ 28.325212] kjournald starting. Commit interval 5 seconds
    [ 28.325228] EXT3-fs: mounted filesystem with ordered data mode.
    [ 29.367019] usb 5-1: new high speed USB device using ehci_hcd and address 2
    [ 29.518222] usb 5-1: configuration #1 chosen from 1 choice
    [ 30.234116] usb 2-2: new full speed USB device using uhci_hcd and address 2
    [ 30.422554] usb 2-2: configuration #1 chosen from 1 choice
    [ 30.661670] usb 4-1: new full speed USB device using uhci_hcd and address 2
    [ 30.834926] usb 4-1: configuration #1 chosen from 1 choice
    [ 31.045912] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 35.993697] ip_tables: (C) 2000-2006 Netfilter Core Team
    [ 36.032761] nf_conntrack version 0.5.0 (7168 buckets, 28672 max)
    [ 36.810447] Linux agpgart interface v0.102
    [ 36.851835] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 36.858152] agpgart: Detected VIA KM400/KM400A chipset
    [ 36.862869] agpgart: AGP aperture is 64M @ 0xe0000000
    [ 36.869039] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 37.030348] input: Power Button (FF) as /devices/virtual/input/input2
    [ 37.039696] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 37.045603] ACPI: Power Button (FF) [PWRF]
    [ 37.045723] input: Power Button (CM) as /devices/virtual/input/input3
    [ 37.059060] ACPI: Power Button (CM) [PWRB]
    [ 38.861291] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x6204
    [ 38.861319] usbcore: registered new interface driver usblp
    [ 39.279037] usbcore: registered new interface driver libusual
    [ 39.388136] Initializing USB Mass Storage driver...
    [ 39.428721] scsi4 : SCSI emulation for USB Mass Storage devices
    [ 39.455888] usbcore: registered new interface driver usb-storage
    [ 39.455895] USB Mass Storage support registered.
    [ 39.456035] usb-storage: device found at 2
    [ 39.456037] usb-storage: waiting for device to settle before scanning
    [ 39.491477] input: PC Speaker as /devices/platform/pcspkr/input/input4
    [ 39.646362] Real Time Clock Driver v1.12ac
    [ 39.711213] PCI: Enabling device 0000:00:11.6 (0000 -> 0001)
    [ 39.711542] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
    [ 39.711545] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
    [ 39.711555] ACPI: PCI Interrupt 0000:00:11.6[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 20
    [ 40.078254] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
    [ 40.110610] parport_pc 00:0a: reported by Plug and Play ACPI
    [ 40.110710] parport0: PC-style at 0x378 (0x77, irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
    [ 40.459572] PCI: Setting latency timer of device 0000:00:11.6 to 64
    [ 40.963271] ACPI: PCI interrupt for device 0000:00:11.6 disabled
    [ 40.963294] VIA 82xx Modem: probe of 0000:00:11.6 failed with error -13
    [ 40.963454] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 20
    [ 40.963591] PCI: Setting latency timer of device 0000:00:11.5 to 64
    [ 43.033478] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 43.244849] lp0: using parport0 (interrupt-driven).
    [ 43.312542] Adding 1317288k swap on /dev/sda5. Priority:-1 extents:1 across:1317288k
    [ 43.865525] EXT3 FS on sda3, internal journal
    [ 44.004702] device-mapper: uevent: version 1.0.3
    [ 44.004743] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
    [ 44.449094] usb-storage: device scan complete
    [ 44.452073] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
    [ 44.455039] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
    [ 44.458019] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
    [ 44.461005] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
    [ 44.505043] sd 4:0:0:0: [sdb] Attached SCSI removable disk
    [ 44.505095] sd 4:0:0:0: Attached scsi generic sg3 type 0
    [ 44.548989] sd 4:0:0:1: [sdc] Attached SCSI removable disk
    [ 44.549038] sd 4:0:0:1: Attached scsi generic sg4 type 0
    [ 44.591942] sd 4:0:0:2: [sdd] Attached SCSI removable disk
    [ 44.591993] sd 4:0:0:2: Attached scsi generic sg5 type 0
    [ 44.639895] sd 4:0:0:3: [sde] Attached SCSI removable disk
    [ 44.639952] sd 4:0:0:3: Attached scsi generic sg6 type 0
    [ 46.072599] PPP generic driver version 2.4.2
    [ 46.115275] NET: Registered protocol family 10
    [ 46.115548] lo: Disabled Privacy Extensions
    [ 46.921867] No dock devices found.
    [ 47.807745] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
    [ 47.807752] apm: overridden by ACPI.
    [ 49.027266] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 51.452759] ppdev: user-space parallel port driver
    [ 51.668355] audit(1240438980.547:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5342 profile="/usr/sbin/cupsd" namespace="default"
    [ 53.361813] eth0: link down
    [ 53.361950] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 54.365409] Bluetooth: Core ver 2.11
    [ 54.367509] NET: Registered protocol family 31
    [ 54.367515] Bluetooth: HCI device and connection manager initialized
    [ 54.367519] Bluetooth: HCI socket layer initialized
    [ 54.379276] Bluetooth: L2CAP ver 2.9
    [ 54.379283] Bluetooth: L2CAP socket layer initialized
    [ 54.456377] Bluetooth: RFCOMM socket layer initialized
    [ 54.456403] Bluetooth: RFCOMM TTY layer initialized
    [ 54.456405] Bluetooth: RFCOMM ver 1.8
    [ 55.021068] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 55.389352] [drm] Initialized drm 1.1.0 20060810
    [ 55.420503] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21
    [ 55.420666] [drm] Initialized via 2.11.1 20070202 on minor 0
    [ 55.454569] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
    [ 55.454593] agpgart: Device is in legacy mode, falling back to 2.x
    [ 55.454599] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
    [ 55.454658] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
    [ 61.014848] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 396.668278] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 401.815188] PPP BSD Compression module registered
    [ 401.918246] PPP Deflate Compression module registered
    [ 402.660716] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 630.424588] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 630.903465] usb 5-8: new high speed USB device using ehci_hcd and address 5
    [ 631.173971] usb 5-8: configuration #1 chosen from 1 choice
    [ 631.457411] phy0 -> rt2500usb_init_eeprom: Error - Invalid RT chipset detected.
    [ 631.457422] phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
    [ 631.457467] usbcore: registered new interface driver rt2500usb
    [ 631.730053] phy1: Selected rate control algorithm 'simple'
    [ 631.794606] usbcore: registered new interface driver rt73usb
    [ 636.418376] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 798.250617] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 800.702537] usbcore: deregistering interface driver rt2500usb
    [ 804.244408] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    '
    [ 930.113928] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 933.049941] usbcore: deregistering interface driver rt73usb
    [ 936.107719] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 1020.020738] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 1022.412159] phy0 -> rt2500usb_init_eeprom: Error - Invalid RT chipset detected.
    [ 1022.412169] phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
    [ 1022.412220] usbcore: registered new interface driver rt2500usb
    [ 1026.014522] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 1151.884045] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 1152.788762] usbcore: deregistering interface driver rt2500usb
    [ 1157.877843] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 1175.859198] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 1181.410536] phy0: Selected rate control algorithm 'simple'
    [ 1181.411209] usbcore: registered new interface driver rt73usb
    [ 1181.852978] ACPI: Unable to turn cooling device [d9d62f18] 'on'

    [ 1199.834358] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    [ 1204.931201] usbcore: registered new interface driver rt2500usb
    [ 1205.828130] ACPI: Unable to turn cooling device [d9d62f18] 'on'
    cousinlucky@cousinlucky-desktop:~$

    I really appreciate your help with this, Waterhead. Thanks!
    PCLinuxOS Gnome and PCLinuxOS Mate
    Linux user # 414321
    You Should Not Give In To Evils, But Proceed Ever More Boldly Against Them!! -from book six of Virgil's Aeneid
    Everything Within The Universe Is Related; We Are All Cousins!!

  6. #36
    Linux Guru
    Join Date
    Jul 2004
    Posts
    4,593
    I think that it is time to give up on trying to get this driver to work. I don't recall what distro and kernel version that you are using, could you refresh my memory?

    You should either install the latest version of your distro, or you can just install the latest version of the drivers. You can download the latest driver source from here.

    Download - Linux Wireless
    Please do not send Private Messages to me with requests for help. I will not reply.

  7. #37
    Linux Enthusiast cousinlucky's Avatar
    Join Date
    Dec 2005
    Location
    New York City
    Posts
    676
    I installed this Ubuntu 8.04 os two months ago. The wicd is installed in my machine and the previous manager has been removed. None of the wicd " preferences " have been put in because i do not know what to put in the sections.
    If I click " connect " on the deskttop icon the screen comes up saying no wireless network found.

    cousinlucky@cousinlucky-desktop:~$ uname -r
    2.6.24-23-386
    cousinlucky@cousinlucky-desktop:~$

    I found this in your link but I am not sure of what to do with it.

    If you are on:

    * 2.6.23
    * 2.6.24
    * 2.6.25
    * 2.6.26

    You can use compat-wireless-old and if you want to have support for WMM or 802.11n then you will need enabled in your kernel:

    * CONFIG_NETDEVICES_MULTIQUEUE
    * CONFIG_NET_SCHED

    If you do not have these enabled you will not get WMM or 802.11n support. Note that if you are on a kernel between 2.6.23..2.6.26 you should not have CONFIG_MAC80211_QOS enabled as part of your kenrnel as this was not part of your kernel, it was removed on 2.6.23 because the new CONFIG_NET_SCHED and CONFIG_NETDEVICES_MULTIQUEUE handled it for us. If you have compilation issues related to CONFIG_MAC80211_QOS please report this to our linux-wireless mailing list.

    How do I determine if the two config files listed above are in my computer?

    Maybe I should try to use the the USB adapter in my suse 10 partition where the connection instuctions are a little simpler to understand.
    PCLinuxOS Gnome and PCLinuxOS Mate
    Linux user # 414321
    You Should Not Give In To Evils, But Proceed Ever More Boldly Against Them!! -from book six of Virgil's Aeneid
    Everything Within The Universe Is Related; We Are All Cousins!!

  8. #38
    Linux Guru
    Join Date
    Jul 2004
    Posts
    4,593
    Suse 10 is a bit old, the driver may be different in it. Try it if you like.

    Even though Ubuntu 8.04 isn't all that old, I still would install the latest drivers.
    Please do not send Private Messages to me with requests for help. I will not reply.

  9. #39
    Linux Enthusiast cousinlucky's Avatar
    Join Date
    Dec 2005
    Location
    New York City
    Posts
    676
    Is there a terminal command that I can use to determine the status, if any, of the configurations mentioned?
    PCLinuxOS Gnome and PCLinuxOS Mate
    Linux user # 414321
    You Should Not Give In To Evils, But Proceed Ever More Boldly Against Them!! -from book six of Virgil's Aeneid
    Everything Within The Universe Is Related; We Are All Cousins!!

  10. #40
    Linux Guru
    Join Date
    Jul 2004
    Posts
    4,593
    If you are not trying to use a type n wireless, then I wouldn't worry about that.

    I say we give up trying to get the installed driver to work, and re-install it. This time using the compat-wireless package. It contains many open-source drivers, not just the one for your specific wireless.

    The kernel that you have is just fine. You should be able to use the latest version, not the "old" version. But, I could be wrong!

    EDIT: OK, I am wrong! You need to use compat-wireless-old for your kernel.
    Please do not send Private Messages to me with requests for help. I will not reply.

Page 4 of 5 FirstFirst 1 2 3 4 5 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •