n4rky

Hello all,

I've been working on this for a while. Here is what I think is the relevant portion of dmesg output:

[ 7.641647] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
[ 7.641650] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[ 7.641710] iwlagn 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 7.641719] iwlagn 0000:0c:00.0: setting latency timer to 64
[ 7.641761] iwlagn: Detected Intel Wireless WiFi Link 5100AGN REV=0x54
[ 7.663840] iwlagn: Tunable channels: 13 802.11bg, 24 802.11a channels
[ 7.687110] iwlagn 0000:0c:00.0: PCI INT A disabled
[ 7.687228] input: PC Speaker as /devices/platform/pcspkr/input/input12
[ 7.687581] wmaster0 (iwlagn): not using net_device_ops yet
[ 7.687841] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 7.745293] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 7.811907] wlan0 (iwlagn): not using net_device_ops yet

This is on Debian Lenny with their latest experimental kernel:
Linux graton 2.6.29-2-686-bigmem #1 SMP Sat May 30 01:27:14 UTC 2009 i686 GNU/Linux
The machine is a Dell Inspiron 1545 laptop.

As you can see, it recognizes the device and seems to know what to do with it. I found and installed the supposedly required firmware in /lib/firmware . I do not see, however, that it is being loaded. Now for the rest of "follow the stupid instructions, stupid:"

graton# apt-get install wireless-tools
Reading package lists... Done
Building dependency tree
Reading state information... Done
wireless-tools is already the newest version.
0 upgraded, 0 newly installed, 0 to remove and 1 not upgraded.
graton# modprobe iwlagn
graton# iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wmaster0 no wireless extensions.

wlan0 IEEE 802.11abgn ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

graton# ifconfig wlan0 up
SIOCSIFFLAGS: No such file or directory
graton# iwlist wlan0 ap
graton#

The access point exists. I can connect to it under Windows XP (I will never, repeat, never be ready for Vista) or on my old laptop. So now what?

Thanks!

waterhead

I moved this post to it's own thread. It is against forum rules to tack your help request to someone else's. Especially when they are about different wireless chips!

I don't believe that Debian has a decent wireless connection manager. I recommend installing Wicd, then see if the problem still persists.

wicd - home

__________________
Paul

Please do not PM me with requests for help. I will not reply.

n4rky

Sorry, Waterhead.

I was not seeing an option to start a new thread.

I am already using wicd. I will be less diplomatic about the network managers available for Debian and Ubuntu: they are complete garbage.

wicd fails to see any wireless networks.

waterhead

Actually, the NetworkManager for Gnome and KNetworkManager for KDE are quite good. I did not know if they were available in Debian.

We should start from the beginning, with you providing all the information that you can. Read through the post linked to below. It describes how to find all the info we need, and post that info here.

Wireless Setup - Start Here

__________________
Paul

Please do not PM me with requests for help. I will not reply.

n4rky

Okay, here goes....

graton# lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07)
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03)
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03)
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03)
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03)
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93)
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03)
00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03)
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03)
09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] (rev 13)
0c:00.0 Network controller [0280]: Intel Corporation Wireless WiFi Link 5100 [8086:4232]
graton# lsmod
Module Size Used by
visor 13532 0
usbserial 26824 1 visor
ip_queue 6284 0
iptable_filter 2944 0
ip_tables 9908 1 iptable_filter
x_tables 13672 1 ip_tables
binfmt_misc 7132 1
i915 130284 2
drm 133272 3 i915
i2c_algo_bit 4888 1 i915
rfcomm 29560 2
l2cap 17072 9 rfcomm
bluetooth 46012 4 rfcomm,l2cap
ppdev 6224 0
lp 7872 0
parport 30828 2 ppdev,lp
ipv6 231640 30
acpi_cpufreq 7040 0
cpufreq_powersave 1276 0
cpufreq_stats 3588 0
cpufreq_userspace 2712 0
cpufreq_conservative 5456 0
fuse 48084 3
loop 12948 0
dell_laptop 3148 0
dcdbas 6732 1 dell_laptop
arc4 1544 2
ecb 2352 2
i2c_i801 8108 0
serio_raw 4544 0
psmouse 36592 0
i2c_core 20792 4 i915,drm,i2c_algo_bit,i2c_i801
pcspkr 2092 0
iwlagn 70552 0
iwlcore 76772 1 iwlagn
iTCO_wdt 9896 0
rfkill 9540 5 dell_laptop,iwlcore
led_class 3668 1 iwlcore
mac80211 134456 2 iwlagn,iwlcore
uvcvideo 48844 0
cfg80211 32728 3 iwlagn,iwlcore,mac80211
snd_hda_codec_idt 48764 1
videodev 33332 1 uvcvideo
v4l1_compat 11196 2 uvcvideo,videodev
joydev 8560 0
evdev 8160 11
snd_hda_intel 22128 2
snd_hda_codec 58808 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 6000 1 snd_hda_codec
snd_pcm 62792 2 snd_hda_intel,snd_hda_codec
snd_timer 17772 1 snd_pcm
snd 48380 10 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_ hwdep,snd_pcm,snd_timer
soundcore 6204 1 snd
snd_page_alloc 8028 2 snd_hda_intel,snd_pcm
video 16348 0
output 2504 1 video
wmi 6332 0
battery 5832 0
button 5672 0
ac 2872 0
intel_agp 22740 1
agpgart 30648 3 drm,intel_agp
ext3 106800 1
jbd 42236 1 ext3
mbcache 7180 1 ext3
sg 19900 0
sr_mod 12840 0
cdrom 29804 1 sr_mod
sd_mod 28176 4
crc_t10dif 1616 1 sd_mod
usbhid 29072 0
hid 34184 1 usbhid
usb_storage 83528 0
ahci 27556 3
libata 148880 1 ahci
scsi_mod 131812 5 sg,sr_mod,sd_mod,usb_storage,libata
sky2 38708 0
ehci_hcd 30072 0
uhci_hcd 19396 0
usbcore 124940 8 visor,usbserial,uvcvideo,usbhid,usb_storage,ehci_h cd,uhci_hcd
thermal 15052 0
processor 39452 4 acpi_cpufreq,thermal
fan 4104 0
thermal_sys 10272 4 video,thermal,processor,fan
graton# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.29-2-686-bigmem (Debian 2.6.29-6~snapshot.13701) (waldi@debian.org) (gcc version 4.3.3 (GCC) ) #1 SMP Sat May 30 01:27:14 UTC 2009
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000ddabf400 (usable)
[ 0.000000] BIOS-e820: 00000000ddabf400 - 00000000ddac1400 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ddac1400 - 00000000e0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000feda0000 - 00000000feda6000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
[ 0.000000] DMI 2.4 present.
[ 0.000000] last_pfn = 0x120000 max_arch_pfn = 0x1000000
[ 0.000000] kernel direct mapping tables up to 379fe000 @ 7000-d000
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] RAMDISK: 378ee000 - 37fef595
[ 0.000000] Allocated new RAMDISK: 004ee000 - 00bef595
[ 0.000000] Move RAMDISK from 00000000378ee000 - 0000000037fef594 to 004ee000 - 00bef594
[ 0.000000] ACPI: RSDP 000FBDD0, 0024 (r2 DELL )
[ 0.000000] ACPI: XSDT DDAC3E00, 0054 (r1 DELL WN09 27D9050D ASL 61)
[ 0.000000] ACPI: FACP DDAC3C9C, 00F4 (r4 DELL WN09 27D9050D ASL 61)
[ 0.000000] ACPI Warning (tbfadt-056: 32/64X length mismatch in Gpe0Block: 128/64 [20081204]
[ 0.000000] FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
[ 0.000000] ACPI: DSDT DDAC4400, 53BD (r2 INT430 SYSFexxx 1001 INTL 20050624)
[ 0.000000] ACPI: FACS DDAD2C00, 0040
[ 0.000000] ACPI: HPET DDAC3F00, 0038 (r1 DELL WN09 1 ASL 61)
[ 0.000000] ACPI: APIC DDAC4000, 0068 (r1 DELL WN09 27D9050D ASL 47)
[ 0.000000] ACPI: MCFG DDAC3FC0, 003E (r16 DELL WN09 27D9050D ASL 61)
[ 0.000000] ACPI: SLIC DDAC409C, 0176 (r1 DELL WN09 27D9050D ASL 61)
[ 0.000000] ACPI: SSDT DDAC2363, 066C (r1 PmRef CpuPm 3000 INTL 20050624)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 3718MB HIGHMEM available.
[ 0.000000] 889MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 379fe000
[ 0.000000] low ram: 00000000 - 379fe000
[ 0.000000] bootmap 00008000 - 0000ef40
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00379fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 00004e6a74] TEXT DATA BSS ==> [0000100000 - 00004e6a74]
[ 0.000000] #4 [00004e7000 - 00004ee000] INIT_PG_TABLE ==> [00004e7000 - 00004ee000]
[ 0.000000] #5 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000]
[ 0.000000] #6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
[ 0.000000] #7 [00004ee000 - 0000bef595] NEW RAMDISK ==> [00004ee000 - 0000bef595]
[ 0.000000] #8 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000379fe
[ 0.000000] HighMem 0x000379fe -> 0x00120000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000ddabf
[ 0.000000] 0: 0x00100000 -> 0x00120000
[ 0.000000] On node 0 totalpages: 1038942
[ 0.000000] free_area_init_node: node 0, pgdat c03cd0c0, node_mem_map c1000000
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3967 pages, LIFO batch:0
[ 0.000000] Normal zone: 1748 pages used for memmap
[ 0.000000] Normal zone: 221994 pages, LIFO batch:31
[ 0.000000] HighMem zone: 7437 pages used for memmap
[ 0.000000] HighMem zone: 803764 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at e2000000 (gap: e0000000:18000000)
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Allocating 40960 bytes of per cpu data
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1029725
[ 0.000000] Kernel command line: root=/dev/sda5 ro quiet
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1995.048 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 4105808k/4718592k available (1999k kernel code, 49032k reserved, 1059k data, 340k init, 3244804k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffe17000 - 0xfffff000 (1952 kB)
[ 0.004000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.004000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
[ 0.004000] .init : 0xc0403000 - 0xc0458000 ( 340 kB)
[ 0.004000] .data : 0xc02f3d2b - 0xc03fc968 (1059 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02f3d2b (1999 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] hpet clockevent registered
[ 0.004000] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 3990.09 BogoMIPS (lpj=7980192)
[ 0.004000] Security Framework initialized
[ 0.004000] SELinux: Disabled at boot.
[ 0.004000] Mount-cache hash table entries: 512
[ 0.004000] Initializing cgroup subsys ns
[ 0.004000] Initializing cgroup subsys cpuacct
[ 0.004000] Initializing cgroup subsys devices
[ 0.004000] Initializing cgroup subsys freezer
[ 0.004000] Initializing cgroup subsys net_cls
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 2048K
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 0
[ 0.004000] Intel machine check architecture supported.
[ 0.004000] Intel machine check reporting enabled on CPU#0.
[ 0.004000] using mwait in idle threads.
[ 0.004000] Checking 'hlt' instruction... OK.
[ 0.017944] ACPI: Core revision 20081204
[ 0.028464] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.068515] CPU0: Intel(R) Core(TM)2 Duo CPU T6400 @ 2.00GHz stepping 0a
[ 0.072001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine.. 3989.95 BogoMIPS (lpj=797991
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 2048K
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] Intel machine check architecture supported.
[ 0.004000] Intel machine check reporting enabled on CPU#1.
[ 0.156451] CPU1: Intel(R) Core(TM)2 Duo CPU T6400 @ 2.00GHz stepping 0a
[ 0.156462] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.160043] Brought up 2 CPUs
[ 0.160045] Total of 2 processors activated (7980.05 BogoMIPS).
[ 0.160094] CPU0 attaching sched-domain:
[ 0.160097] domain 0: span 0-1 level MC
[ 0.160099] groups: 0 1
[ 0.160103] CPU1 attaching sched-domain:
[ 0.160105] domain 0: span 0-1 level MC
[ 0.160107] groups: 1 0
[ 0.160164] net_namespace: 1056 bytes
[ 0.160164] Booting paravirtualized kernel on bare hardware
[ 0.160170] regulator: core version 0.5
[ 0.160178] NET: Registered protocol family 16
[ 0.160178] ACPI: bus type pci registered
[ 0.160178] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
[ 0.160178] PCI: MCFG area at f8000000 reserved in E820
[ 0.160178] PCI: Using MMCONFIG for extended config space
[ 0.160178] PCI: Using configuration type 1 for base access
[ 0.160178] bio: create slab <bio-0> at 0
[ 0.160756] ACPI: EC: Look up EC in DSDT
[ 0.160948] ACPI: BIOS _OSI(Linux) query ignored
[ 0.205352] ACPI: Interpreter enabled
[ 0.205357] ACPI: (supports S0 S3 S4 S5)
[ 0.205374] ACPI: Using IOAPIC for interrupt routing
[ 0.280155] ACPI: No dock devices found.
[ 0.280165] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.280188] pci 0000:00:02.0: reg 10 64bit mmio: [0xf6c00000-0xf6ffffff]
[ 0.280188] pci 0000:00:02.0: reg 18 64bit mmio: [0xe0000000-0xefffffff]
[ 0.280188] pci 0000:00:02.0: reg 20 io port: [0xefe8-0xefef]
[ 0.280188] pci 0000:00:02.1: reg 10 64bit mmio: [0xf6b00000-0xf6bfffff]
[ 0.280229] pci 0000:00:1a.0: reg 20 io port: [0x6f60-0x6f7f]
[ 0.280326] pci 0000:00:1a.1: reg 20 io port: [0x6f80-0x6f9f]
[ 0.280422] pci 0000:00:1a.2: reg 20 io port: [0x6fa0-0x6fbf]
[ 0.280507] pci 0000:00:1a.7: reg 10 32bit mmio: [0xfed1c400-0xfed1c7ff]
[ 0.280601] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.280606] pci 0000:00:1a.7: PME# disabled
[ 0.280651] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf6afc000-0xf6afffff]
[ 0.280726] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.280730] pci 0000:00:1b.0: PME# disabled
[ 0.280816] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.280821] pci 0000:00:1c.0: PME# disabled
[ 0.280908] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.280913] pci 0000:00:1c.1: PME# disabled
[ 0.281001] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.281006] pci 0000:00:1c.2: PME# disabled
[ 0.281095] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.281099] pci 0000:00:1c.4: PME# disabled
[ 0.281164] pci 0000:00:1d.0: reg 20 io port: [0x6f00-0x6f1f]
[ 0.281260] pci 0000:00:1d.1: reg 20 io port: [0x6f20-0x6f3f]
[ 0.281355] pci 0000:00:1d.2: reg 20 io port: [0x6f40-0x6f5f]
[ 0.281439] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfed1c000-0xfed1c3ff]
[ 0.281534] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.281540] pci 0000:00:1d.7: PME# disabled
[ 0.281771] pci 0000:00:1f.2: reg 10 io port: [0x6e70-0x6e77]
[ 0.281779] pci 0000:00:1f.2: reg 14 io port: [0x6e78-0x6e7b]
[ 0.281787] pci 0000:00:1f.2: reg 18 io port: [0x6e80-0x6e87]
[ 0.281794] pci 0000:00:1f.2: reg 1c io port: [0x6e88-0x6e8b]
[ 0.281802] pci 0000:00:1f.2: reg 20 io port: [0x6ea0-0x6ebf]
[ 0.281810] pci 0000:00:1f.2: reg 24 32bit mmio: [0xfed1c800-0xfed1cfff]
[ 0.281888] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.281893] pci 0000:00:1f.2: PME# disabled
[ 0.281930] pci 0000:00:1f.3: reg 10 64bit mmio: [0xf6afbf00-0xf6afbfff]
[ 0.281950] pci 0000:00:1f.3: reg 20 io port: [0x1100-0x111f]
[ 0.282120] pci 0000:0c:00.0: reg 10 64bit mmio: [0xf69fe000-0xf69fffff]
[ 0.282262] pci 0000:0c:00.0: PME# supported from D0 D3hot D3cold
[ 0.282269] pci 0000:0c:00.0: PME# disabled
[ 0.282352] pci 0000:00:1c.1: bridge 32bit mmio: [0xf6900000-0xf69fffff]
[ 0.282417] pci 0000:09:00.0: reg 10 64bit mmio: [0xf68fc000-0xf68fffff]
[ 0.282429] pci 0000:09:00.0: reg 18 io port: [0xde00-0xdeff]
[ 0.282538] pci 0000:09:00.0: supports D1 D2
[ 0.282540] pci 0000:09:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.282546] pci 0000:09:00.0: PME# disabled
[ 0.282621] pci 0000:00:1c.2: bridge io port: [0xd000-0xdfff]
[ 0.282625] pci 0000:00:1c.2: bridge 32bit mmio: [0xf6800000-0xf68fffff]
[ 0.282691] pci 0000:00:1c.4: bridge io port: [0xc000-0xcfff]
[ 0.282696] pci 0000:00:1c.4: bridge 32bit mmio: [0xf6600000-0xf67fffff]
[ 0.282704] pci 0000:00:1c.4: bridge 64bit mmio pref: [0xf0000000-0xf01fffff]
[ 0.282772] pci 0000:00:1e.0: transparent bridge
[ 0.282817] pci_bus 0000:00: on NUMA node 0
[ 0.282822] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.283057] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[ 0.283156] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.283223] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.283290] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.284006] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.296634] ACPI: PCI Interrupt Link [LNKA] (IRQs *10 11)
[ 0.296634] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *4
[ 0.296634] ACPI: PCI Interrupt Link [LNKC] (IRQs *10 11)
[ 0.296634] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 10 11) *0, disabled.
[ 0.296634] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.296693] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.296816] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.296927] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.296991] PCI: Using ACPI for IRQ routing
[ 0.316015] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.316021] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.340004] pnp: PnP ACPI init
[ 0.340011] ACPI: bus type pnp registered
[ 0.392202] pnp: PnP ACPI: found 13 devices
[ 0.392204] ACPI: ACPI bus type pnp unregistered
[ 0.392207] PnPBIOS: Disabled by ACPI PNP
[ 0.392215] system 00:01: iomem range 0xff800000-0xff8fffff has been reserved
[ 0.392219] system 00:01: iomem range 0xffc00000-0xffcfffff has been reserved
[ 0.392230] system 00:09: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.392236] system 00:0a: ioport range 0x900-0x97f has been reserved
[ 0.392240] system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[ 0.392243] system 00:0a: ioport range 0x1000-0x1005 has been reserved
[ 0.392246] system 00:0a: ioport range 0x1008-0x100f has been reserved
[ 0.392252] system 00:0b: ioport range 0xf400-0xf4fe has been reserved
[ 0.392255] system 00:0b: ioport range 0x1006-0x1007 has been reserved
[ 0.392259] system 00:0b: ioport range 0x100a-0x1059 could not be reserved
[ 0.392262] system 00:0b: ioport range 0x1060-0x107f has been reserved
[ 0.392265] system 00:0b: ioport range 0x1080-0x10bf has been reserved
[ 0.392268] system 00:0b: ioport range 0x1100-0x111f has been reserved
[ 0.392271] system 00:0b: ioport range 0x1010-0x102f has been reserved
[ 0.392274] system 00:0b: ioport range 0x809-0x809 has been reserved
[ 0.392281] system 00:0c: iomem range 0x0-0x9efff could not be reserved
[ 0.392284] system 00:0c: iomem range 0x9f000-0x9ffff could not be reserved
[ 0.392287] system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
[ 0.392290] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[ 0.392293] system 00:0c: iomem range 0x100000-0xddabf3ff could not be reserved
[ 0.392297] system 00:0c: iomem range 0xddabf400-0xddafffff could not be reserved
[ 0.392300] system 00:0c: iomem range 0xddb00000-0xddbfffff has been reserved
[ 0.392304] system 00:0c: iomem range 0xffe00000-0xffffffff has been reserved
[ 0.392307] system 00:0c: iomem range 0xffa00000-0xffbfffff has been reserved
[ 0.392310] system 00:0c: iomem range 0xfec00000-0xfec0ffff has been reserved
[ 0.392313] system 00:0c: iomem range 0xfee00000-0xfee0ffff has been reserved
[ 0.392317] system 00:0c: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.392320] system 00:0c: iomem range 0xfeda0000-0xfeda3fff has been reserved
[ 0.392323] system 00:0c: iomem range 0xfeda4000-0xfeda4fff has been reserved
[ 0.392327] system 00:0c: iomem range 0xfeda5000-0xfeda5fff has been reserved
[ 0.392330] system 00:0c: iomem range 0xfeda6000-0xfeda6fff has been reserved
[ 0.392334] system 00:0c: iomem range 0xfed1c800-0xfed1cfff has been reserved
[ 0.392337] system 00:0c: iomem range 0xfed18000-0xfed1bfff has been reserved
[ 0.392340] system 00:0c: iomem range 0xf8000000-0xfbffffff has been reserved
[ 0.427259] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:0b
[ 0.427261] pci 0000:00:1c.0: IO window: disabled
[ 0.427267] pci 0000:00:1c.0: MEM window: disabled
[ 0.427272] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.427280] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:0c
[ 0.427282] pci 0000:00:1c.1: IO window: disabled
[ 0.427288] pci 0000:00:1c.1: MEM window: 0xf6900000-0xf69fffff
[ 0.427293] pci 0000:00:1c.1: PREFETCH window: disabled
[ 0.427301] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:09
[ 0.427304] pci 0000:00:1c.2: IO window: 0xd000-0xdfff
[ 0.427311] pci 0000:00:1c.2: MEM window: 0xf6800000-0xf68fffff
[ 0.427315] pci 0000:00:1c.2: PREFETCH window: disabled
[ 0.427323] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0d
[ 0.427327] pci 0000:00:1c.4: IO window: 0xc000-0xcfff
[ 0.427333] pci 0000:00:1c.4: MEM window: 0xf6600000-0xf67fffff
[ 0.427338] pci 0000:00:1c.4: PREFETCH window: 0x000000f0000000-0x000000f01fffff
[ 0.427346] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03
[ 0.427348] pci 0000:00:1e.0: IO window: disabled
[ 0.427354] pci 0000:00:1e.0: MEM window: disabled
[ 0.427359] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.427376] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.427381] pci 0000:00:1c.0: setting latency timer to 64
[ 0.427391] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.427396] pci 0000:00:1c.1: setting latency timer to 64
[ 0.427405] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.427410] pci 0000:00:1c.2: setting latency timer to 64
[ 0.427419] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.427424] pci 0000:00:1c.4: setting latency timer to 64
[ 0.427432] pci 0000:00:1e.0: setting latency timer to 64
[ 0.427436] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.427438] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.427440] pci_bus 0000:0b: resource 0 mem: [0x0-0x0]
[ 0.427442] pci_bus 0000:0b: resource 1 mem: [0x0-0x0]
[ 0.427444] pci_bus 0000:0b: resource 2 mem: [0x0-0x0]
[ 0.427446] pci_bus 0000:0b: resource 3 mem: [0x0-0x0]
[ 0.427448] pci_bus 0000:0c: resource 0 mem: [0x0-0x0]
[ 0.427449] pci_bus 0000:0c: resource 1 mem: [0xf6900000-0xf69fffff]
[ 0.427451] pci_bus 0000:0c: resource 2 mem: [0x0-0x0]
[ 0.427453] pci_bus 0000:0c: resource 3 mem: [0x0-0x0]
[ 0.427455] pci_bus 0000:09: resource 0 io: [0xd000-0xdfff]
[ 0.427457] pci_bus 0000:09: resource 1 mem: [0xf6800000-0xf68fffff]
[ 0.427459] pci_bus 0000:09: resource 2 mem: [0x0-0x0]
[ 0.427461] pci_bus 0000:09: resource 3 mem: [0x0-0x0]
[ 0.427463] pci_bus 0000:0d: resource 0 io: [0xc000-0xcfff]
[ 0.427465] pci_bus 0000:0d: resource 1 mem: [0xf6600000-0xf67fffff]
[ 0.427467] pci_bus 0000:0d: resource 2 mem: [0xf0000000-0xf01fffff]
[ 0.427469] pci_bus 0000:0d: resource 3 mem: [0x0-0x0]
[ 0.427471] pci_bus 0000:03: resource 0 mem: [0x0-0x0]
[ 0.427473] pci_bus 0000:03: resource 1 mem: [0x0-0x0]
[ 0.427475] pci_bus 0000:03: resource 2 mem: [0x0-0x0]
[ 0.427476] pci_bus 0000:03: resource 3 io: [0x00-0xffff]
[ 0.427479] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.427520] NET: Registered protocol family 2
[ 0.472053] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.472335] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.472684] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.472861] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.472863] TCP reno registered
[ 0.484060] NET: Registered protocol family 1
[ 0.484154] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[ 0.503995] Switched to high resolution mode on CPU 0
[ 0.722442] it is
[ 0.984463] Freeing initrd memory: 7173k freed
[ 0.985200] audit: initializing netlink socket (disabled)
[ 0.985213] type=2000 audit(1244297754.985:1): initialized
[ 0.985595] highmem bounce pool size: 64 pages
[ 0.985599] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.985673] VFS: Disk quotas dquot_6.5.2
[ 0.985703] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.985751] msgmni has been set to 1697
[ 0.985868] alg: No test for stdrng (krng)
[ 0.985912] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.985915] io scheduler noop registered
[ 0.985917] io scheduler anticipatory registered
[ 0.985918] io scheduler deadline registered
[ 0.985934] io scheduler cfq registered (default)
[ 0.985946] pci 0000:00:02.0: Boot video device
[ 0.986202] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.986287] pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.986450] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[ 0.986528] pcieport-driver 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 0.986690] pcieport-driver 0000:00:1c.2: setting latency timer to 64
[ 0.986768] pcieport-driver 0000:00:1c.2: irq 26 for MSI/MSI-X
[ 0.986928] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 0.987008] pcieport-driver 0000:00:1c.4: irq 27 for MSI/MSI-X
[ 0.987360] isapnp: Scanning for PnP cards...
[ 1.341249] isapnp: No Plug & Play device found
[ 1.343698] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.345497] brd: module loaded
[ 1.345582] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.369959] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.385457] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.385462] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.385465] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.385467] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.385470] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.385585] mice: PS/2 mouse device common for all mice
[ 1.385651] rtc_cmos 00:04: RTC can wake from S4
[ 1.387714] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.387748] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.387780] cpuidle: using governor ladder
[ 1.387782] cpuidle: using governor menu
[ 1.387786] No iBFT detected.
[ 1.388137] TCP cubic registered
[ 1.388139] NET: Registered protocol family 17
[ 1.388148] Using IPI No-Shortcut mode
[ 1.388254] registered taskstats version 1
[ 1.388397] rtc_cmos 00:04: setting system clock to 2009-06-06 14:15:56 UTC (1244297756)
[ 1.388580] Freeing unused kernel memory: 340k freed
[ 1.540395] ACPI: SSDT DDAC29CF, 023F (r1 PmRef BspIst 3000 INTL 20050624)
[ 1.540705] ACPI: SSDT DDAC2DE5, 05C6 (r1 PmRef BspCst 3001 INTL 20050624)
[ 1.541014] Monitor-Mwait will be used to enter C-1 state
[ 1.541021] Monitor-Mwait will be used to enter C-2 state
[ 1.541026] Monitor-Mwait will be used to enter C-3 state
[ 1.541168] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 1.541212] processor ACPI_CPU:00: registered as cooling_device0
[ 1.541216] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.541583] ACPI: SSDT DDAC2C0E, 01D7 (r1 PmRef ApIst 3000 INTL 20050624)
[ 1.541887] ACPI: SSDT DDAC33AB, 008D (r1 PmRef ApCst 3000 INTL 20050624)
[ 1.542290] Marking TSC unstable due to TSC halts in idle
[ 1.542444] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 1.542496] processor ACPI_CPU:01: registered as cooling_device1
[ 1.542499] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.591310] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.656349] ACPI: Thermal Zone [THM] (37 C)
[ 1.684650] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.886451] usbcore: registered new interface driver usbfs
[ 1.886482] usbcore: registered new interface driver hub
[ 1.886512] usbcore: registered new device driver usb
[ 1.888235] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.888280] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.888290] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 1.888294] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.888330] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.888367] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00006f60
[ 1.888406] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.888409] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.888411] usb usb1: Product: UHCI Host Controller
[ 1.888412] usb usb1: Manufacturer: Linux 2.6.29-2-686-bigmem uhci_hcd
[ 1.888414] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.888468] usb usb1: configuration #1 chosen from 1 choice
[ 1.888492] hub 1-0:1.0: USB hub found
[ 1.888498] hub 1-0:1.0: 2 ports detected
[ 1.888592] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.888599] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 1.888602] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.888622] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 1.888656] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00006f80
[ 1.888688] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.888690] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.888692] usb usb2: Product: UHCI Host Controller
[ 1.888694] usb usb2: Manufacturer: Linux 2.6.29-2-686-bigmem uhci_hcd
[ 1.888696] usb usb2: SerialNumber: 0000:00:1a.1
[ 1.888737] usb usb2: configuration #1 chosen from 1 choice
[ 1.888761] hub 2-0:1.0: USB hub found
[ 1.888766] hub 2-0:1.0: 2 ports detected
[ 1.888854] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 1.888861] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 1.888865] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 1.888884] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[ 1.888918] uhci_hcd 0000:00:1a.2: irq 22, io base 0x00006fa0
[ 1.888951] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.888953] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.888955] usb usb3: Product: UHCI Host Controller
[ 1.888957] usb usb3: Manufacturer: Linux 2.6.29-2-686-bigmem uhci_hcd
[ 1.888959] usb usb3: SerialNumber: 0000:00:1a.2
[ 1.889000] usb usb3: configuration #1 chosen from 1 choice
[ 1.889024] hub 3-0:1.0: USB hub found
[ 1.889029] hub 3-0:1.0: 2 ports detected
[ 1.889118] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.889124] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.889128] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.889148] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 1.889175] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006f00
[ 1.889205] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.889208] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.889210] usb usb4: Product: UHCI Host Controller
[ 1.889212] usb usb4: Manufacturer: Linux 2.6.29-2-686-bigmem uhci_hcd
[ 1.889213] usb usb4: SerialNumber: 0000:00:1d.0
[ 1.889255] usb usb4: configuration #1 chosen from 1 choice
[ 1.889277] hub 4-0:1.0: USB hub found
[ 1.889282] hub 4-0:1.0: 2 ports detected
[ 1.889370] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.889377] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.889380] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.889400] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 1.889428] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006f20
[ 1.889458] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.889460] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.889462] usb usb5: Product: UHCI Host Controller
[ 1.889464] usb usb5: Manufacturer: Linux 2.6.29-2-686-bigmem uhci_hcd
[ 1.889466] usb usb5: SerialNumber: 0000:00:1d.1
[ 1.889508] usb usb5: configuration #1 chosen from 1 choice
[ 1.889532] hub 5-0:1.0: USB hub found
[ 1.889537] hub 5-0:1.0: 2 ports detected
[ 1.889626] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 1.889633] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.889636] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.889654] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 1.889683] uhci_hcd 0000:00:1d.2: irq 22, io base 0x00006f40
[ 1.889715] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.889718] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.889720] usb usb6: Product: UHCI Host Controller
[ 1.889721] usb usb6: Manufacturer: Linux 2.6.29-2-686-bigmem uhci_hcd
[ 1.889723] usb usb6: SerialNumber: 0000:00:1d.2
[ 1.889765] usb usb6: configuration #1 chosen from 1 choice
[ 1.889788] hub 6-0:1.0: USB hub found
[ 1.889793] hub 6-0:1.0: 2 ports detected
[ 1.891910] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.891913] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 1.891940] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[ 1.891982] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 1.891985] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.892067] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
[ 1.895972] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.895979] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 1.895986] ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfed1c400
[ 1.904618] sky2 driver version 1.22
[ 1.904651] sky2 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.904663] sky2 0000:09:00.0: setting latency timer to 64
[ 1.904711] sky2 0000:09:00.0: Yukon-2 FE+ chip revision 0
[ 1.904840] sky2 0000:09:00.0: irq 28 for MSI/MSI-X
[ 1.905184] sky2 eth0: addr 00:23:ae:39:34:11
[ 1.912028] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 1.912068] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.912071] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.912073] usb usb7: Product: EHCI Host Controller
[ 1.912075] usb usb7: Manufacturer: Linux 2.6.29-2-686-bigmem ehci_hcd
[ 1.912077] usb usb7: SerialNumber: 0000:00:1a.7
[ 1.912143] usb usb7: configuration #1 chosen from 1 choice
[ 1.912171] hub 7-0:1.0: USB hub found
[ 1.912179] hub 7-0:1.0: 6 ports detected
[ 1.912297] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.912324] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.912327] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.912351] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
[ 1.916269] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.916276] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.916282] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfed1c000
[ 1.932019] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.932048] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.932050] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.932053] usb usb8: Product: EHCI Host Controller
[ 1.932055] usb usb8: Manufacturer: Linux 2.6.29-2-686-bigmem ehci_hcd
[ 1.932056] usb usb8: SerialNumber: 0000:00:1d.7
[ 1.932126] usb usb8: configuration #1 chosen from 1 choice
[ 1.932164] hub 8-0:1.0: USB hub found
[ 1.932171] hub 8-0:1.0: 6 ports detected
[ 2.010710] SCSI subsystem initialized
[ 2.036282] libata version 3.00 loaded.
[ 2.039342] ahci 0000:00:1f.2: version 3.0
[ 2.039356] ahci 0000:00:1f.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.039421] ahci 0000:00:1f.2: irq 29 for MSI/MSI-X
[ 2.039469] ahci: SSS flag set, parallel bus scan disabled
[ 2.039505] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[ 2.039509] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems
[ 2.039514] ahci 0000:00:1f.2: setting latency timer to 64
[ 2.039764] scsi0 : ahci
[ 2.039857] scsi1 : ahci
[ 2.039904] scsi2 : ahci
[ 2.039958] scsi3 : ahci
[ 2.040045] scsi4 : ahci
[ 2.040091] scsi5 : ahci
[ 2.040568] ata1: SATA max UDMA/133 abar m2048@0xfed1c800 port 0xfed1c900 irq 29
[ 2.040571] ata2: SATA max UDMA/133 abar m2048@0xfed1c800 port 0xfed1c980 irq 29
[ 2.040573] ata3: DUMMY
[ 2.040575] ata4: DUMMY
[ 2.040577] ata5: SATA max UDMA/133 abar m2048@0xfed1c800 port 0xfed1cb00 irq 29
[ 2.040581] ata6: SATA max UDMA/133 abar m2048@0xfed1c800 port 0xfed1cb80 irq 29
[ 2.344235] usb 7-5: new high speed USB device using ehci_hcd and address 3
[ 2.356091] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.399188] ata1.00: ATA-8: WDC WD3200BEVT-75ZCT2, 11.01A11, max UDMA/133
[ 2.399193] ata1.00: 625142448 sectors, multi 8: LBA48 NCQ (depth 31/32)
[ 2.401762] ata1.00: configured for UDMA/133
[ 2.416346] scsi 0:0:0:0: Direct-Access ATA WDC WD3200BEVT-7 11.0 PQ: 0 ANSI: 5
[ 2.487193] usb 7-5: New USB device found, idVendor=0bda, idProduct=0158
[ 2.487197] usb 7-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.487201] usb 7-5: Product: USB2.0-CRW
[ 2.487204] usb 7-5: Manufacturer: Generic
[ 2.487207] usb 7-5: SerialNumber: 20071114173400000
[ 2.487289] usb 7-5: configuration #1 chosen from 1 choice
[ 2.500011] Clocksource tsc unstable (delta = -123097558 ns)
[ 2.508553] Initializing USB Mass Storage driver...
[ 2.510054] scsi6 : SCSI emulation for USB Mass Storage devices
[ 2.510136] usbcore: registered new interface driver usb-storage
[ 2.510138] USB Mass Storage support registered.
[ 2.510351] usb-storage: device found at 3
[ 2.510353] usb-storage: waiting for device to settle before scanning
[ 2.604217] usb 7-6: new high speed USB device using ehci_hcd and address 4
[ 2.742818] usb 7-6: New USB device found, idVendor=05ca, idProduct=180a
[ 2.742822] usb 7-6: New USB device strings: Mfr=9, Product=2, SerialNumber=0
[ 2.742826] usb 7-6: Product: Integrated Webcam
[ 2.742829] usb 7-6: Manufacturer: M091R-R01-9430-SH07J
[ 2.742928] usb 7-6: configuration #1 chosen from 1 choice
[ 2.980228] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 3.144256] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.145443] ata2.00: ATAPI: HL-DT-ST DVD+/-RW GT10N, A105, max UDMA/100
[ 3.146938] ata2.00: configured for UDMA/100
[ 3.151437] usb 1-1: New USB device found, idVendor=0a5c, idProduct=4500
[ 3.151441] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.151444] usb 1-1: Product: BCM2046B1
[ 3.151447] usb 1-1: Manufacturer: Broadcom
[ 3.151558] usb 1-1: configuration #1 chosen from 1 choice
[ 3.154454] hub 1-1:1.0: USB hub found
[ 3.158512] hub 1-1:1.0: 3 ports detected
[ 3.161166] scsi 1:0:0:0: CD-ROM HL-DT-ST DVD+-RW GT10N A105 PQ: 0 ANSI: 5
[ 3.437436] usb 1-1.1: new full speed USB device using uhci_hcd and address 3
[ 3.480237] ata5: SATA link down (SStatus 0 SControl 300)
[ 3.556446] usb 1-1.1: New USB device found, idVendor=413c, idProduct=8161
[ 3.556450] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.556550] usb 1-1.1: configuration #1 chosen from 1 choice
[ 3.592835] usbcore: registered new interface driver hiddev
[ 3.596653] input: HID 413c:8161 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/input/input1
[ 3.616288] generic-usb 0003:413C:8161.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 413c:8161] on usb-0000:00:1a.0-1.1/input0
[ 3.616312] usbcore: registered new interface driver usbhid
[ 3.616316] usbhid: v2.6:USB HID core driver
[ 3.634424] usb 1-1.2: new full speed USB device using uhci_hcd and address 4
[ 3.759446] usb 1-1.2: New USB device found, idVendor=413c, idProduct=8162
[ 3.759451] usb 1-1.2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.759556] usb 1-1.2: configuration #1 chosen from 1 choice
[ 3.769787] input: HID 413c:8162 as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input2
[ 3.789077] generic-usb 0003:413C:8162.0002: input,hidraw1: USB HID v1.11 Mouse [HID 413c:8162] on usb-0000:00:1a.0-1.2/input0
[ 3.816325] ata6: SATA link down (SStatus 0 SControl 300)
[ 3.862928] Driver 'sd' needs updating - please use bus_type methods
[ 3.863013] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 3.863026] sd 0:0:0:0: [sda] Write Protect is off
[ 3.863028] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.863048] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.863101] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[ 3.863113] sd 0:0:0:0: [sda] Write Protect is off
[ 3.863115] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.863134] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.863139] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 3.900680] sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 3.944940] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.952988] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.952993] Uniform CD-ROM driver Revision: 3.20
[ 3.953086] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.964151] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.964176] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 4.299534] PM: Starting manual resume from disk
[ 4.367606] kjournald starting. Commit interval 5 seconds
[ 4.367644] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.971125] udevd version 125 started
[ 6.372120] Linux agpgart interface v0.103
[ 6.447301] agpgart-intel 0000:00:00.0: Intel Mobile Intel® GM45 Express Chipset
[ 6.448094] agpgart-intel 0000:00:00.0: detected 32764K stolen memory
[ 6.451728] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[ 6.500349] ACPI: AC Adapter [AC] (on-line)
[ 6.523266] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[ 6.524523] ACPI: Lid Switch [LID]
[ 6.524571] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[ 6.541024] ACPI: Power Button (CM) [PBTN]
[ 6.721844] atkbd.c: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
[ 6.721847] atkbd.c: Use 'setkeycodes e00d <keycode>' to make it known.
[ 6.734487] ACPI: Battery Slot [BAT0] (battery present)
[ 6.734561] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
[ 6.749013] ACPI: Sleep Button (CM) [SBTN]
[ 6.749112] ACPI: WMI: Mapper loaded
[ 6.993938] acpi device:3c: registered as cooling_device2
[ 6.994653] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:3a/input/input6
[ 7.009035] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 7.009118] ACPI Warning (nspredef-0434): \_SB_.PCI0.VID2._DOD: Return Package has no elements (empty) [20081204]
[ 7.009204] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:41/input/input7
[ 7.025610] ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
[ 7.135728] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 7.135791] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 7.204406] Linux video capture interface: v2.00
[ 7.220687] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
[ 7.257060] cfg80211: Using static regulatory domain info
[ 7.257063] cfg80211: Regulatory domain: US
[ 7.257065] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 7.257068] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 7.257070] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 7.257073] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 7.257075] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 7.257078] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 7.257080] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 7.257083] cfg80211: Calling CRDA for country: US
[ 7.270126] uvcvideo: Found UVC 1.00 device Integrated Webcam (05ca:180a)
[ 7.270622] input: Integrated Webcam as /devices/pci0000:00/0000:00:1a.7/usb7/7-6/7-6:1.0/input/input9
[ 7.365099] usbcore: registered new interface driver uvcvideo
[ 7.365103] USB Video Class driver (v0.1.0)
[ 7.374259] input: HDA Intel Mic at Ext Right Jack as /devices/pci0000:00/0000:00:1b.0/input/input10
[ 7.389106] input: HDA Intel HP Out at Ext Right Jack as /devices/pci0000:00/0000:00:1b.0/input/input11
[ 7.517062] usb-storage: device scan complete
[ 7.519064] scsi 6:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
[ 7.520196] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 7.520298] iTCO_wdt: Found a ICH9M TCO device (Version=2, TCOBASE=0x1060)
[ 7.520358] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 7.521616] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 7.521657] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 7.641647] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
[ 7.641650] iwlagn: Copyright(c) 2003-2008 Intel Corporation
[ 7.641710] iwlagn 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 7.641719] iwlagn 0000:0c:00.0: setting latency timer to 64
[ 7.641761] iwlagn: Detected Intel Wireless WiFi Link 5100AGN REV=0x54
[ 7.663840] iwlagn: Tunable channels: 13 802.11bg, 24 802.11a channels
[ 7.687110] iwlagn 0000:0c:00.0: PCI INT A disabled
[ 7.687228] input: PC Speaker as /devices/platform/pcspkr/input/input12
[ 7.687581] wmaster0 (iwlagn): not using net_device_ops yet
[ 7.687841] phy0: Selected rate control algorithm 'iwl-agn-rs'
[ 7.745293] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 7.811907] wlan0 (iwlagn): not using net_device_ops yet
[ 7.828884] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 8.281426] input: PS/2 Mouse as /devices/platform/i8042/serio2/input/input13
[ 8.337888] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio2/input/input14
[ 10.280362] Adding 2658716k swap on /dev/sda6. Priority:-1 extents:1 across:2658716k
[ 10.694762] EXT3 FS on sda5, internal journal
[ 11.335906] loop: module loaded
[ 11.660045] fuse init (API version 7.11)
[ 17.260888] NET: Registered protocol family 10
[ 17.261780] lo: Disabled Privacy Extensions
[ 19.768743] lp: driver loaded but no devices found
[ 19.851960] ppdev: user-space parallel port driver
[ 33.428378] sky2 eth0: enabling interface
[ 33.428744] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 34.929942] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[ 34.930248] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 34.973674] Bluetooth: Core ver 2.14
[ 34.973743] NET: Registered protocol family 31
[ 34.973746] Bluetooth: HCI device and connection manager initialized
[ 34.973750] Bluetooth: HCI socket layer initialized
[ 35.054488] Bluetooth: L2CAP ver 2.11
[ 35.054492] Bluetooth: L2CAP socket layer initialized
[ 35.233054] Bluetooth: RFCOMM socket layer initialized
[ 35.233069] Bluetooth: RFCOMM TTY layer initialized
[ 35.233072] Bluetooth: RFCOMM ver 1.10
[ 35.656156] sky2 eth0: disabling interface
[ 35.998894] sky2 eth0: enabling interface
[ 35.999217] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 37.541123] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[ 37.541317] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 39.042630] [drm] Initialized drm 1.1.0 20060810
[ 39.084281] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 39.084290] pci 0000:00:02.0: setting latency timer to 64
[ 39.086239] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[ 39.086244] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 39.086270] pci 0000:00:02.0: irq 30 for MSI/MSI-X
[ 39.086298] [drm] Initialized i915 1.6.0 20080730 on minor 0
[ 39.148166] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[ 40.346605] set status page addr 0x01fff000
[ 48.004068] eth0: no IPv6 routers present
[ 118.360752] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 138.548440] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
[ 3078.347900] iwlagn 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 3078.347989] iwlagn 0000:0c:00.0: restoring config space at offset 0x1 (was 0x100102, writing 0x100106)
[ 3078.348122] iwlagn 0000:0c:00.0: irq 31 for MSI/MSI-X
[ 3078.348197] iwlagn 0000:0c:00.0: firmware: requesting iwlwifi-5000-1.ucode
[ 3078.509643] iwlagn: iwlwifi-5000-1.ucode firmware file req failed: Reason -2
[ 3078.509647] iwlagn: Could not read microcode: -2
[ 3078.509687] iwlagn 0000:0c:00.0: PCI INT A disabled
[ 9994.633171] usb 8-3: new high speed USB device using ehci_hcd and address 2
[ 9994.766901] usb 8-3: New USB device found, idVendor=05e3, idProduct=0608
[ 9994.766907] usb 8-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 9994.766911] usb 8-3: Product: USB2.0 Hub
[ 9994.767037] usb 8-3: configuration #1 chosen from 1 choice
[ 9994.767771] hub 8-3:1.0: USB hub found
[ 9994.768191] hub 8-3:1.0: 4 ports detected
[ 9995.040441] usb 8-3.1: new full speed USB device using ehci_hcd and address 3
[ 9995.137503] usb 8-3.1: New USB device found, idVendor=0830, idProduct=0061
[ 9995.137508] usb 8-3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 9995.137512] usb 8-3.1: Product: Palm Handheld
[ 9995.137515] usb 8-3.1: Manufacturer: Palm, Inc.
[ 9995.137518] usb 8-3.1: SerialNumber: PalmSN12345678
[ 9995.137656] usb 8-3.1: configuration #1 chosen from 1 choice
[ 9995.233517] usb 8-3.2: new high speed USB device using ehci_hcd and address 4
[ 9995.286245] usbcore: registered new interface driver usbserial
[ 9995.286259] USB Serial support registered for generic
[ 9995.351906] usb 8-3.2: New USB device found, idVendor=152e, idProduct=2507
[ 9995.351911] usb 8-3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 9995.351915] usb 8-3.2: Product: Super Multi Rewriter
[ 9995.351918] usb 8-3.2: Manufacturer: HLDS Inc.
[ 9995.351921] usb 8-3.2: SerialNumber: P01030313111425
[ 9995.352055] usb 8-3.2: configuration #1 chosen from 1 choice
[ 9995.352457] scsi7 : SCSI emulation for USB Mass Storage devices
[ 9995.352642] usb-storage: device found at 4
[ 9995.352644] usb-storage: waiting for device to settle before scanning
[ 9995.352701] usbcore: registered new interface driver usbserial_generic
[ 9995.352704] usbserial: USB Serial Driver core
[ 9995.355046] USB Serial support registered for Handspring Visor / Palm OS
[ 9995.355057] USB Serial support registered for Sony Clie 3.5
[ 9995.355068] USB Serial support registered for Sony Clie 5.0
[ 9995.356177] visor 8-3.1:1.0: Handspring Visor / Palm OS converter detected
[ 9995.356240] usb 8-3.1: Handspring Visor / Palm OS converter now attached to ttyUSB0
[ 9995.356280] usb 8-3.1: Handspring Visor / Palm OS converter now attached to ttyUSB1
[ 9995.356293] usbcore: registered new interface driver visor
[ 9995.356295] visor: USB HandSpring Visor / Palm OS driver
[10000.352387] usb-storage: device scan complete
[10000.388169] scsi 7:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-E60L 1.00 PQ: 0 ANSI: 0
[10000.396886] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[10000.397035] sr 7:0:0:0: Attached scsi CD-ROM sr1
[10000.397138] sr 7:0:0:0: Attached scsi generic sg3 type 5
graton#

Thanks!

n4rky

Oh, and more....

graton# dmesg | grep firmware
[ 3078.348197] iwlagn 0000:0c:00.0: firmware: requesting iwlwifi-5000-1.ucode
[ 3078.509643] iwlagn: iwlwifi-5000-1.ucode firmware file req failed: Reason -2

Ho, ho! I hadn't spotted this before. But what does reason -2 mean?

and finally....

graton# uname -r
2.6.29-2-686-bigmem

n4rky

So why does it want that file and not the one I got:

graton# ls -al /lib/firmware
total 888
drwxr-xr-x 2 root root 4096 2009-06-03 21:02 .
drwxr-xr-x 17 root root 4096 2009-06-03 14:13 ..
-rw-r--r-- 1 root root 150860 2009-03-29 23:34 iwlwifi-3945-1.ucode
-rw-r--r-- 1 root root 187608 2009-03-29 23:34 iwlwifi-4965-1.ucode
-rw-r--r-- 1 root root 187672 2009-03-29 23:34 iwlwifi-4965-2.ucode
-rw-r--r-- 1 root root 353240 2009-06-03 21:02 iwlwifi-5000-2.ucode

Or, if it really should have the file it is asking for, where do I find it rather than the one I found?

n4rky

So I went back to the intellinuxwireless site (sorry, not only does this forum software not allow me to post urls--it really enforces this) , clicked on show older releases and found an older tar ball with the version of the file the message in dmesg is asking for. And I copied it in to /lib/firmware.

But is using an older version of the firmware what I really want to do?

Hal343

Yes-sometimes the newer stuff is broken, so try the older one and see if it works. If it does you're golden. If not we'll have to investigate further.

__________________
Registered Linux User #420832

waterhead

The link-posting ban is to prevent spammers from registering and immediately posting spam. Sorry but it is needed. In fact it may get even stricter in the future!

I have found that the firmware tarballs are not really named according to the firmware that it contains. You may need to download and unpack several of the older versions before you find the version that you need.

I'm not completely sure what determines which firmware it needs. It most likely is the chip version and/or driver version. Fortunately Linux knows what it needs, you just have to provide it.

__________________
Paul

Please do not PM me with requests for help. I will not reply.