Find the answer to your Linux question:
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12
Wired connection is OK but wireless won't connect. It shows wireless network and also loads but then starts asking password(which is correct) and won't connect. I have tried everything(download many ...
Enjoy an ad free experience by logging in. Not a member yet? Register.
  1. #1
    Just Joined!
    Join Date
    Aug 2010
    Posts
    10

    Lightbulb Wifi problem, won't connect!


    Wired connection is OK but wireless won't connect. It shows wireless network and also loads but then starts asking password(which is correct) and won't connect. I have tried everything(download many things and searching in the internet but in the end nothing changes the problem is still unsolved.
    Just a little help what to do. Dell Inspiron 1525, driver Broadcom

    Code:
    00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub [8086:2a00] (rev 0c)
    	Kernel driver in use: agpgart-intel
    	Kernel modules: intel-agp
    00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a02] (rev 0c)
    	Kernel driver in use: i915
    	Kernel modules: i915
    00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a03] (rev 0c)
    00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02)
    	Kernel driver in use: ehci_hcd
    00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02)
    	Kernel driver in use: HDA Intel
    	Kernel modules: snd-hda-intel
    00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02)
    	Kernel driver in use: pcieport
    	Kernel modules: shpchp
    00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 02)
    	Kernel driver in use: pcieport
    	Kernel modules: shpchp
    00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 [8086:2847] (rev 02)
    	Kernel driver in use: pcieport
    	Kernel modules: shpchp
    00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02)
    	Kernel driver in use: ehci_hcd
    00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f2)
    00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller [8086:2815] (rev 02)
    	Kernel modules: iTCO_wdt
    00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller [8086:2850] (rev 02)
    	Kernel driver in use: ata_piix
    00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller [8086:2829] (rev 02)
    	Kernel driver in use: ahci
    	Kernel modules: ahci
    00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 02)
    	Kernel modules: i2c-i801
    02:09.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (rev 05)
    	Kernel driver in use: ohci1394
    	Kernel modules: firewire-ohci, ohci1394
    02:09.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 22)
    	Kernel driver in use: sdhci-pci
    	Kernel modules: sdhci-pci
    02:09.2 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller [1180:0843] (rev 12)
    	Kernel driver in use: ricoh-mmc
    	Kernel modules: ricoh_mmc
    02:09.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 12)
    02:09.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev ff)
    09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] (rev 12)
    	Kernel driver in use: sky2
    	Kernel modules: sky2
    0b:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01)
    	Kernel driver in use: b43-pci-bridge
    	Kernel modules: ssb
    Code:
    Module                  Size  Used by
    binfmt_misc             6587  1 
    ppdev                   5259  0 
    b43                   163523  0 
    mac80211              205146  1 b43
    b44                    25574  0 
    cfg80211              126517  2 b43,mac80211
    ssb                    38671  2 b43,b44
    mii                     4381  1 b44
    ndiswrapper           184677  0 
    dm_crypt               11331  0 
    snd_hda_codec_idt      53916  1 
    snd_hda_codec_intelhdmi     9559  1 
    snd_hda_intel          20799  2 
    snd_hda_codec          87096  3 snd_hda_codec_idt,snd_hda_codec_intelhdmi,snd_hda_intel
    snd_hwdep               5668  1 snd_hda_codec
    snd_pcm_oss            34603  0 
    snd_mixer_oss          13929  1 snd_pcm_oss
    snd_pcm                71678  3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
    snd_seq_dummy           1498  0 
    snd_seq_oss            27626  0 
    arc4                    1153  2 
    snd_seq_midi            4621  0 
    snd_rawmidi            19141  1 snd_seq_midi
    snd_seq_midi_event      6003  2 snd_seq_oss,snd_seq_midi
    snd_seq                48042  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
    snd_timer              18710  2 snd_pcm,snd_seq
    snd_seq_device          6052  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
    snd                    56687  19 snd_hda_codec_idt,snd_hda_codec_intelhdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
    joydev                  8708  0 
    soundcore               6620  1 snd
    sdhci_pci               5470  0 
    sdhci                  15462  1 sdhci_pci
    ricoh_mmc               2923  0 
    snd_page_alloc          7140  2 snd_hda_intel,snd_pcm
    uvcvideo               56990  0 
    videodev               34361  1 uvcvideo
    psmouse                63245  0 
    v4l1_compat            13251  2 uvcvideo,videodev
    dell_wmi                1793  0 
    led_class               2864  2 b43,sdhci
    serio_raw               3978  0 
    lp                      7028  0 
    dell_laptop             6856  0 
    parport                32635  2 ppdev,lp
    dcdbas                  5422  1 dell_laptop
    dm_raid45              81647  0 
    xor                    15028  1 dm_raid45
    fbcon                  35102  71 
    tileblit                2031  1 fbcon
    font                    7557  1 fbcon
    bitblit                 4707  1 fbcon
    softcursor              1189  1 bitblit
    vga16fb                11385  0 
    vgastate                8961  1 vga16fb
    i915                  285076  3 
    drm_kms_helper         29297  1 i915
    drm                   162409  4 i915,drm_kms_helper
    ohci1394               26950  0 
    ieee1394               81181  1 ohci1394
    intel_agp              24119  2 i915
    i2c_algo_bit            5028  1 i915
    ahci                   32200  2 
    sky2                   40775  0 
    agpgart                31724  2 drm,intel_agp
    video                  17375  1 i915
    output                  1871  1 video
    Code:
    [    0.000000] Initializing cgroup subsys cpuset
    [    0.000000] Initializing cgroup subss cpu
    [    0.000000] Linux version 2.6.32-24-generic (buildd@vernadsky) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #41-Ubuntu SMP Thu Aug 19 01:12:52 UTC 2010 (Ubuntu 2.6.32-24.41-generic 2.6.32.15+drm33.5)
    [    0.000000] KERNEL supported cpus:
    [    0.000000]   Intel GenuineIntel
    [    0.000000]   AMD AuthenticAMD
    [    0.000000]   NSC Geode by NSC
    [    0.000000]   Cyrix CyrixInstead
    [    0.000000]   Centaur CentaurHauls
    [    0.000000]   Transmeta GenuineTMx86
    [    0.000000]   Transmeta TransmetaCPU
    [    0.000000]   UMC UMC UMC UMC
    [    0.000000] BIOS-provided physical RAM map:
    [    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
    [    0.000000]  BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
    [    0.000000]  BIOS-e820: 0000000000100000 - 000000007f66d800 (usable)
    [    0.000000]  BIOS-e820: 000000007f66d800 - 0000000080000000 (reserved)
    [    0.000000]  BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
    [    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
    [    0.000000]  BIOS-e820: 00000000fed18000 - 00000000fed1c000 (reserved)
    [    0.000000]  BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
    [    0.000000]  BIOS-e820: 00000000feda0000 - 00000000feda6000 (reserved)
    [    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
    [    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
    [    0.000000] DMI 2.4 present.
    [    0.000000] last_pfn = 0x7f66d max_arch_pfn = 0x100000
    [    0.000000] MTRR default type: uncachable
    [    0.000000] MTRR fixed ranges enabled:
    [    0.000000]   00000-9FFFF write-back
    [    0.000000]   A0000-BFFFF uncachable
    [    0.000000]   C0000-CFFFF write-protect
    [    0.000000]   D0000-EFFFF uncachable
    [    0.000000]   F0000-FFFFF write-protect
    [    0.000000] MTRR variable ranges enabled:
    [    0.000000]   0 base 000000000 mask F80000000 write-back
    [    0.000000]   1 base 07F800000 mask FFF800000 uncachable
    [    0.000000]   2 base 07F700000 mask FFFF00000 uncachable
    [    0.000000]   3 disabled
    [    0.000000]   4 disabled
    [    0.000000]   5 disabled
    [    0.000000]   6 disabled
    [    0.000000]   7 disabled
    [    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [    0.000000] e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved)
    [    0.000000] Scanning 1 areas for low memory corruption
    [    0.000000] modified physical RAM map:
    [    0.000000]  modified: 0000000000000000 - 0000000000002000 (usable)
    [    0.000000]  modified: 0000000000002000 - 0000000000006000 (reserved)
    [    0.000000]  modified: 0000000000006000 - 000000000009f000 (usable)
    [    0.000000]  modified: 000000000009f000 - 00000000000a0000 (reserved)
    [    0.000000]  modified: 0000000000100000 - 000000007f66d800 (usable)
    [    0.000000]  modified: 000000007f66d800 - 0000000080000000 (reserved)
    [    0.000000]  modified: 00000000f8000000 - 00000000fc000000 (reserved)
    [    0.000000]  modified: 00000000fec00000 - 00000000fec10000 (reserved)
    [    0.000000]  modified: 00000000fed18000 - 00000000fed1c000 (reserved)
    [    0.000000]  modified: 00000000fed20000 - 00000000fed90000 (reserved)
    [    0.000000]  modified: 00000000feda0000 - 00000000feda6000 (reserved)
    [    0.000000]  modified: 00000000fee00000 - 00000000fee10000 (reserved)
    [    0.000000]  modified: 00000000ffe00000 - 0000000100000000 (reserved)
    [    0.000000] initial memory mapped : 0 - 00c00000
    [    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
    [    0.000000] Using x86 segment limits to approximate NX protection
    [    0.000000]  0000000000 - 0000400000 page 4k
    [    0.000000]  0000400000 - 0037400000 page 2M
    [    0.000000]  0037400000 - 00377fe000 page 4k
    [    0.000000] kernel direct mapping tables up to 377fe000 @ 7000-c000
    [    0.000000] RAMDISK: 372dc000 - 37fefac5
    [    0.000000] Allocated new RAMDISK: 008e2000 - 015f5ac5
    [    0.000000] Move RAMDISK from 00000000372dc000 - 0000000037fefac4 to 008e2000 - 015f5ac4
    [    0.000000] ACPI: RSDP 000fbc60 00024 (v02 DELL  )
    [    0.000000] ACPI: XSDT 7f66f200 00064 (v01 DELL    M08     27D80614 ASL  00000061)
    [    0.000000] ACPI: FACP 7f66f09c 000F4 (v04 DELL    M08     27D80614 ASL  00000061)
    [    0.000000] ACPI: DSDT 7f66f800 05477 (v02 INT430 SYSFexxx 00001001 INTL 20050624)
    [    0.000000] ACPI: FACS 7f67e000 00040
    [    0.000000] ACPI: HPET 7f66f300 00038 (v01 DELL    M08     00000001 ASL  00000061)
    [    0.000000] ACPI: APIC 7f66f400 00068 (v01 DELL    M08     27D80614 ASL  00000047)
    [    0.000000] ACPI: MCFG 7f66f3c0 0003E (v16 DELL    M08     27D80614 ASL  00000061)
    [    0.000000] ACPI: SLIC 7f66f49c 00176 (v01 DELL    M08     27D80614 ASL  00000061)
    [    0.000000] ACPI: OSFR 7f66ea00 0002C (v01 DELL    M08     27D80614 ASL  00000061)
    [    0.000000] ACPI: BOOT 7f66efc0 00028 (v01 DELL    M08     27D80614 ASL  00000061)
    [    0.000000] ACPI: SSDT 7f66d9c0 004CC (v01  PmRef    CpuPm 00003000 INTL 20050624)
    [    0.000000] ACPI: Local APIC address 0xfee00000
    [    0.000000] 1150MB HIGHMEM available.
    [    0.000000] 887MB LOWMEM available.
    [    0.000000]   mapped low ram: 0 - 377fe000
    [    0.000000]   low ram: 0 - 377fe000
    [    0.000000]   node 0 low ram: 00000000 - 377fe000
    [    0.000000]   node 0 bootmap 00008000 - 0000ef00
    [    0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
    [    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
    [    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
    [    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
    [    0.000000]   #3 [0000100000 - 00008ddeb8]    TEXT DATA BSS ==> [0000100000 - 00008ddeb8]
    [    0.000000]   #4 [000009f000 - 0000100000]    BIOS reserved ==> [000009f000 - 0000100000]
    [    0.000000]   #5 [00008de000 - 00008e1184]              BRK ==> [00008de000 - 00008e1184]
    [    0.000000]   #6 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
    [    0.000000]   #7 [00008e2000 - 00015f5ac5]      NEW RAMDISK ==> [00008e2000 - 00015f5ac5]
    [    0.000000]   #8 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
    [    0.000000] Zone PFN ranges:
    [    0.000000]   DMA      0x00000000 -> 0x00001000
    [    0.000000]   Normal   0x00001000 -> 0x000377fe
    [    0.000000]   HighMem  0x000377fe -> 0x0007f66d
    [    0.000000] Movable zone start PFN for each node
    [    0.000000] early_node_map[3] active PFN ranges
    [    0.000000]     0: 0x00000000 -> 0x00000002
    [    0.000000]     0: 0x00000006 -> 0x0000009f
    [    0.000000]     0: 0x00000100 -> 0x0007f66d
    [    0.000000] On node 0 totalpages: 521736
    [    0.000000] free_area_init_node: node 0, pgdat c079a780, node_mem_map c15f7000
    [    0.000000]   DMA zone: 32 pages used for memmap
    [    0.000000]   DMA zone: 0 pages reserved
    [    0.000000]   DMA zone: 3963 pages, LIFO batch:0
    [    0.000000]   Normal zone: 1744 pages used for memmap
    [    0.000000]   Normal zone: 221486 pages, LIFO batch:31
    [    0.000000]   HighMem zone: 2301 pages used for memmap
    [    0.000000]   HighMem zone: 292210 pages, LIFO batch:31
    [    0.000000] Using APIC driver default
    [    0.000000] ACPI: PM-Timer IO Port: 0x1008
    [    0.000000] ACPI: Local APIC address 0xfee00000
    [    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [    0.000000] ACPI: IRQ0 used by override.
    [    0.000000] ACPI: IRQ2 used by override.
    [    0.000000] ACPI: IRQ9 used by override.
    [    0.000000] Using ACPI (MADT) for SMP configuration information
    [    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
    [    0.000000] nr_irqs_gsi: 24
    [    0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000
    [    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    [    0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
    [    0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:78000000)
    [    0.000000] Booting paravirtualized kernel on bare hardware
    [    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
    [    0.000000] PERCPU: Embedded 14 pages/cpu @c2800000 s36056 r0 d21288 u2097152
    [    0.000000] pcpu-alloc: s36056 r0 d21288 u2097152 alloc=1*4194304
    [    0.000000] pcpu-alloc: [0] 0 1 
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 517659
    [    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-24-generic root=UUID=5d2a1e40-da6b-4d0d-90b3-7767162848f9 ro quiet splash
    [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [    0.000000] Enabling fast FPU save and restore... done.
    [    0.000000] Enabling unmasked SIMD FPU exception support... done.
    [    0.000000] Initializing CPU#0
    [    0.000000] allocated 10436740 bytes of page_cgroup
    [    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [    0.000000] Initializing HighMem for node 0 (000377fe:0007f66d)
    [    0.000000] Memory: 2036976k/2087348k available (4679k kernel code, 48960k reserved, 2124k data, 660k init, 1178044k highmem)
    [    0.000000] virtual kernel memory layout:
    [    0.000000]     fixmap  : 0xfff1d000 - 0xfffff000   ( 904 kB)
    [    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    [    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
    [    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
    [    0.000000]       .init : 0xc07a5000 - 0xc084a000   ( 660 kB)
    [    0.000000]       .data : 0xc0591e33 - 0xc07a4e88   (2124 kB)
    [    0.000000]       .text : 0xc0100000 - 0xc0591e33   (4679 kB)
    [    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [    0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [    0.000000] Hierarchical RCU implementation.
    [    0.000000] NR_IRQS:2304 nr_irqs:424
    [    0.000000] Extended CMOS year: 2000
    [    0.000000] Console: colour VGA+ 80x25
    [    0.000000] console [tty0] enabled
    [    0.000000] hpet clockevent registered
    [    0.000000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [    0.000000] Fast TSC calibration using PIT
    [    0.000000] Detected 1861.955 MHz processor.
    [    0.004006] Calibrating delay loop (skipped), value calculated using timer frequency.. 3723.91 BogoMIPS (lpj=7447820)
    [    0.004027] Security Framework initialized
    [    0.004051] AppArmor: AppArmor initialized
    [    0.004059] Mount-cache hash table entries: 512
    [    0.004209] Initializing cgroup subsys ns
    [    0.004214] Initializing cgroup subsys cpuacct
    [    0.004219] Initializing cgroup subsys memory
    [    0.004228] Initializing cgroup subsys devices
    [    0.004231] Initializing cgroup subsys freezer
    [    0.004233] Initializing cgroup subsys net_cls
    [    0.004256] CPU: L1 I cache: 32K, L1 D cache: 32K
    [    0.004260] CPU: L2 cache: 1024K
    [    0.004263] CPU: Physical Processor ID: 0
    [    0.004265] CPU: Processor Core ID: 0
    [    0.004269] mce: CPU supports 6 MCE banks
    [    0.004279] CPU0: Thermal monitoring enabled (TM2)
    [    0.004283] using mwait in idle threads.
    [    0.004292] Performance Events: Core2 events, Intel PMU driver.
    [    0.004302] ... version:                2
    [    0.004304] ... bit width:              40
    [    0.004306] ... generic registers:      2
    [    0.004308] ... value mask:             000000ffffffffff
    [    0.004310] ... max period:             000000007fffffff
    [    0.004312] ... fixed-purpose events:   3
    [    0.004314] ... event mask:             0000000700000003
    [    0.004320] Checking 'hlt' instruction... OK.
    [    0.022975] ACPI: Core revision 20090903
    [    0.034831] ftrace: converting mcount calls to 0f 1f 44 00 00
    [    0.034838] ftrace: allocating 21780 entries in 43 pages
    [    0.036071] Enabling APIC mode:  Flat.  Using 1 I/O APICs
    [    0.036463] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [    0.077776] CPU0: Intel(R) Pentium(R) Dual  CPU  T2390  @ 1.86GHz stepping 0d
    [    0.080001] Booting processor 1 APIC 0x1 ip 0x6000
    [    0.008000] Initializing CPU#1
    [    0.008000] CPU: L1 I cache: 32K, L1 D cache: 32K
    [    0.008000] CPU: L2 cache: 1024K
    [    0.008000] CPU: Physical Processor ID: 0
    [    0.008000] CPU: Processor Core ID: 1
    [    0.008000] CPU1: Thermal monitoring enabled (TM2)
    [    0.164056] CPU1: Intel(R) Pentium(R) Dual  CPU  T2390  @ 1.86GHz stepping 0d
    [    0.164070] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
    [    0.168021] Brought up 2 CPUs
    [    0.168024] Total of 2 processors activated (7447.85 BogoMIPS).
    [    0.168422] CPU0 attaching sched-domain:
    [    0.168425]  domain 0: span 0-1 level MC
    [    0.168428]   groups: 0 1
    [    0.168435] CPU1 attaching sched-domain:
    [    0.168438]  domain 0: span 0-1 level MC
    [    0.168440]   groups: 1 0
    [    0.168548] devtmpfs: initialized
    [    0.168548] regulator: core version 0.5
    [    0.168548] Time: 12:13:15  Date: 08/27/10
    [    0.168548] NET: Registered protocol family 16
    [    0.168548] Trying to unpack rootfs image as initramfs...
    [    0.168548] EISA bus registered
    [    0.168548] ACPI: bus type pci registered
    [    0.168548] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
    [    0.168548] PCI: MCFG area at f8000000 reserved in E820
    [    0.168548] PCI: Using MMCONFIG for extended config space
    [    0.168548] PCI: Using configuration type 1 for base access
    [    0.172135] bio: create slab <bio-0> at 0
    [    0.173162] ACPI: EC: Look up EC in DSDT
    [    0.202203] ACPI: Interpreter enabled
    [    0.202221] ACPI: (supports S0 S3 S4 S5)
    [    0.202248] ACPI: Using IOAPIC for interrupt routing
    [    0.248505] ACPI: No dock devices found.
    [    0.267925] ACPI: PCI Root Bridge [PCI0] (0000:00)
    [    0.268101] pci 0000:00:02.0: reg 10 64bit mmio: [0xfea00000-0xfeafffff]
    [    0.268111] pci 0000:00:02.0: reg 18 64bit mmio pref: [0xe0000000-0xefffffff]
    [    0.268118] pci 0000:00:02.0: reg 20 io port: [0xeff8-0xefff]
    [    0.268171] pci 0000:00:02.1: reg 10 64bit mmio: [0xfeb00000-0xfebfffff]
    [    0.268312] pci 0000:00:1a.0: reg 20 io port: [0x6f20-0x6f3f]
    [    0.268392] pci 0000:00:1a.1: reg 20 io port: [0x6f00-0x6f1f]
    [    0.268481] pci 0000:00:1a.7: reg 10 32bit mmio: [0xfed1c400-0xfed1c7ff]
    [    0.268560] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    [    0.268566] pci 0000:00:1a.7: PME# disabled
    [    0.268633] pci 0000:00:1b.0: reg 10 64bit mmio: [0xfe9fc000-0xfe9fffff]
    [    0.268708] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [    0.268714] pci 0000:00:1b.0: PME# disabled
    [    0.268833] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [    0.268838] pci 0000:00:1c.0: PME# disabled
    [    0.268957] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [    0.268963] pci 0000:00:1c.1: PME# disabled
    [    0.269085] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    [    0.269091] pci 0000:00:1c.4: PME# disabled
    [    0.269171] pci 0000:00:1d.0: reg 20 io port: [0x6f80-0x6f9f]
    [    0.269253] pci 0000:00:1d.1: reg 20 io port: [0x6f60-0x6f7f]
    [    0.269335] pci 0000:00:1d.2: reg 20 io port: [0x6f40-0x6f5f]
    [    0.269421] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfed1c000-0xfed1c3ff]
    [    0.269499] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [    0.269506] pci 0000:00:1d.7: PME# disabled
    [    0.269717] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
    [    0.269723] pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
    [    0.269728] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0900 (mask 007f)
    [    0.269733] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 006c (mask 0007)
    [    0.269738] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0c80 (mask 003f)
    [    0.269803] pci 0000:00:1f.1: reg 10 io port: [0x1f0-0x1f7]
    [    0.269812] pci 0000:00:1f.1: reg 14 io port: [0x3f4-0x3f7]
    [    0.269822] pci 0000:00:1f.1: reg 18 io port: [0x170-0x177]
    [    0.269831] pci 0000:00:1f.1: reg 1c io port: [0x374-0x377]
    [    0.269841] pci 0000:00:1f.1: reg 20 io port: [0x6fa0-0x6faf]
    [    0.269931] pci 0000:00:1f.2: reg 10 io port: [0x6eb0-0x6eb7]
    [    0.269941] pci 0000:00:1f.2: reg 14 io port: [0x6eb8-0x6ebb]
    [    0.269950] pci 0000:00:1f.2: reg 18 io port: [0x6ec0-0x6ec7]
    [    0.269961] pci 0000:00:1f.2: reg 1c io port: [0x6ec8-0x6ecb]
    [    0.269970] pci 0000:00:1f.2: reg 20 io port: [0x6ee0-0x6eff]
    [    0.269981] pci 0000:00:1f.2: reg 24 32bit mmio: [0xfe9fb800-0xfe9fbfff]
    [    0.270033] pci 0000:00:1f.2: PME# supported from D3hot
    [    0.270039] pci 0000:00:1f.2: PME# disabled
    [    0.270079] pci 0000:00:1f.3: reg 10 32bit mmio: [0xfe9fb700-0xfe9fb7ff]
    [    0.270110] pci 0000:00:1f.3: reg 20 io port: [0x10c0-0x10df]
    [    0.270235] pci 0000:09:00.0: reg 10 64bit mmio: [0xfe8fc000-0xfe8fffff]
    [    0.270248] pci 0000:09:00.0: reg 18 io port: [0xde00-0xdeff]
    [    0.270350] pci 0000:09:00.0: supports D1 D2
    [    0.270352] pci 0000:09:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [    0.270360] pci 0000:09:00.0: PME# disabled
    [    0.270454] pci 0000:00:1c.0: bridge io port: [0xd000-0xdfff]
    [    0.270461] pci 0000:00:1c.0: bridge 32bit mmio: [0xfe800000-0xfe8fffff]
    [    0.270686] pci 0000:0b:00.0: reg 10 64bit mmio: [0xfe7fc000-0xfe7fffff]
    [    0.270921] pci 0000:0b:00.0: supports D1 D2
    [    0.270924] pci 0000:0b:00.0: PME# supported from D0 D3hot D3cold
    [    0.270936] pci 0000:0b:00.0: PME# disabled
    [    0.271093] pci 0000:00:1c.1: bridge 32bit mmio: [0xfe700000-0xfe7fffff]
    [    0.271174] pci 0000:00:1c.4: bridge io port: [0xc000-0xcfff]
    [    0.271180] pci 0000:00:1c.4: bridge 32bit mmio: [0xfe400000-0xfe6fffff]
    [    0.271190] pci 0000:00:1c.4: bridge 64bit mmio pref: [0xf0000000-0xf01fffff]
    [    0.271262] pci 0000:02:09.0: reg 10 32bit mmio: [0xfe3ff800-0xfe3fffff]
    [    0.271337] pci 0000:02:09.0: supports D1 D2
    [    0.271339] pci 0000:02:09.0: PME# supported from D0 D1 D2 D3hot D3cold
    [    0.271346] pci 0000:02:09.0: PME# disabled
    [    0.271397] pci 0000:02:09.1: reg 10 32bit mmio: [0xfe3ff400-0xfe3ff4ff]
    [    0.271470] pci 0000:02:09.1: supports D1 D2
    [    0.271472] pci 0000:02:09.1: PME# supported from D0 D1 D2 D3hot D3cold
    [    0.271478] pci 0000:02:09.1: PME# disabled
    [    0.271531] pci 0000:02:09.2: reg 10 32bit mmio: [0xfe3ff500-0xfe3ff5ff]
    [    0.271603] pci 0000:02:09.2: supports D1 D2
    [    0.271606] pci 0000:02:09.2: PME# supported from D0 D1 D2 D3hot D3cold
    [    0.271612] pci 0000:02:09.2: PME# disabled
    [    0.271664] pci 0000:02:09.3: reg 10 32bit mmio: [0xfe3ff600-0xfe3ff6ff]
    [    0.271738] pci 0000:02:09.3: supports D1 D2
    [    0.271740] pci 0000:02:09.3: PME# supported from D0 D1 D2 D3hot D3cold
    [    0.271746] pci 0000:02:09.3: PME# disabled
    [    0.271798] pci 0000:02:09.4: reg 10 32bit mmio: [0xfe3ff700-0xfe3ff7ff]
    [    0.271870] pci 0000:02:09.4: supports D1 D2
    [    0.271872] pci 0000:02:09.4: PME# supported from D0 D1 D2 D3hot D3cold
    [    0.271879] pci 0000:02:09.4: PME# disabled
    [    0.271945] pci 0000:00:1e.0: transparent bridge
    [    0.271955] pci 0000:00:1e.0: bridge 32bit mmio: [0xfe300000-0xfe3fffff]
    [    0.272011] pci_bus 0000:00: on NUMA node 0
    [    0.272034] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [    0.272366] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
    [    0.272523] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
    [    0.272608] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
    [    0.272697] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
    [    0.287685] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
    [    0.287824] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
    [    0.287959] ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *5
    [    0.288096] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 11) *0, disabled.
    [    0.288231] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
    [    0.288371] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
    [    0.288512] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *7 9 10 11 12 14 15)
    [    0.288632] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
    [    0.288777] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [    0.288799] vgaarb: loaded
    [    0.288939] SCSI subsystem initialized
    [    0.289059] libata version 3.00 loaded.
    [    0.289144] usbcore: registered new interface driver usbfs
    [    0.289158] usbcore: registered new interface driver hub
    [    0.289189] usbcore: registered new device driver usb
    [    0.289379] ACPI: WMI: Mapper loaded
    [    0.289382] PCI: Using ACPI for IRQ routing
    [    0.289711] NetLabel: Initializing
    [    0.289713] NetLabel:  domain hash size = 128
    [    0.289715] NetLabel:  protocols = UNLABELED CIPSOv4
    [    0.289731] NetLabel:  unlabeled traffic allowed by default
    [    0.289774] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [    0.289780] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [    0.292100] Switching to clocksource tsc
    [    0.294426] AppArmor: AppArmor Filesystem Enabled
    [    0.294448] pnp: PnP ACPI init
    [    0.294471] ACPI: bus type pnp registered
    [    0.315073] pnp 00:0a: io resource (0x1000-0x1005) overlaps 0000:00:1f.0 BAR 13 (0x1000-0x107f), disabling
    [    0.315078] pnp 00:0a: io resource (0x1008-0x100f) overlaps 0000:00:1f.0 BAR 13 (0x1000-0x107f), disabling
    [    0.315199] pnp 00:0b: io resource (0x1006-0x1007) overlaps 0000:00:1f.0 BAR 13 (0x1000-0x107f), disabling
    [    0.315203] pnp 00:0b: io resource (0x100a-0x1059) overlaps 0000:00:1f.0 BAR 13 (0x1000-0x107f), disabling
    [    0.315207] pnp 00:0b: io resource (0x1060-0x107f) overlaps 0000:00:1f.0 BAR 13 (0x1000-0x107f), disabling
    [    0.315211] pnp 00:0b: io resource (0x1010-0x102f) overlaps 0000:00:1f.0 BAR 13 (0x1000-0x107f), disabling
    [    0.337865] pnp: PnP ACPI: found 13 devices
    [    0.337870] ACPI: ACPI bus type pnp unregistered
    [    0.337877] PnPBIOS: Disabled by ACPI PNP
    [    0.337894] system 00:01: iomem range 0xff800000-0xff8fffff has been reserved
    [    0.337898] system 00:01: iomem range 0xffc00000-0xffcfffff has been reserved
    [    0.337908] system 00:06: ioport range 0xc80-0xcff could not be reserved
    [    0.337916] system 00:09: iomem range 0xfed00000-0xfed003ff has been reserved
    [    0.337923] system 00:0a: ioport range 0x900-0x97f has been reserved
    [    0.337926] system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
    [    0.337934] system 00:0b: ioport range 0xf400-0xf4fe has been reserved
    [    0.337937] system 00:0b: ioport range 0x1080-0x10bf has been reserved
    [    0.337940] system 00:0b: ioport range 0x10c0-0x10df has been reserved
    [    0.337943] system 00:0b: ioport range 0x809-0x809 has been reserved
    [    0.337951] system 00:0c: iomem range 0x0-0x9efff could not be reserved
    [    0.337954] system 00:0c: iomem range 0x9f000-0x9ffff could not be reserved
    [    0.337957] system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
    [    0.337960] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
    [    0.337964] system 00:0c: iomem range 0x100000-0x7f66d7ff could not be reserved
    [    0.337967] system 00:0c: iomem range 0x7f66d800-0x7f6fffff has been reserved
    [    0.337970] system 00:0c: iomem range 0x7f700000-0x7f7fffff has been reserved
    [    0.337974] system 00:0c: iomem range 0x7f700000-0x7fefffff could not be reserved
    [    0.337977] system 00:0c: iomem range 0xffe00000-0xffffffff has been reserved
    [    0.337980] system 00:0c: iomem range 0xffa00000-0xffbfffff has been reserved
    [    0.337983] system 00:0c: iomem range 0xfec00000-0xfec0ffff could not be reserved
    [    0.337987] system 00:0c: iomem range 0xfee00000-0xfee0ffff has been reserved
    [    0.337990] system 00:0c: iomem range 0xfed20000-0xfed8ffff has been reserved
    [    0.337993] system 00:0c: iomem range 0xfeda0000-0xfeda3fff has been reserved
    [    0.337996] system 00:0c: iomem range 0xfeda4000-0xfeda4fff has been reserved
    [    0.337999] system 00:0c: iomem range 0xfeda5000-0xfeda5fff has been reserved
    [    0.338002] system 00:0c: iomem range 0xfeda6000-0xfeda6fff has been reserved
    [    0.338006] system 00:0c: iomem range 0xfed18000-0xfed1bfff has been reserved
    [    0.338009] system 00:0c: iomem range 0xf8000000-0xfbffffff has been reserved
    [    0.372829] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:09
    [    0.372836] pci 0000:00:1c.0:   IO window: 0xd000-0xdfff
    [    0.372844] pci 0000:00:1c.0:   MEM window: 0xfe800000-0xfe8fffff
    [    0.372851] pci 0000:00:1c.0:   PREFETCH window: 0x00000080000000-0x000000801fffff
    [    0.372860] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:0b
    [    0.372864] pci 0000:00:1c.1:   IO window: 0x2000-0x2fff
    [    0.372872] pci 0000:00:1c.1:   MEM window: 0xfe700000-0xfe7fffff
    [    0.372878] pci 0000:00:1c.1:   PREFETCH window: 0x00000080200000-0x000000803fffff
    [    0.372888] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0c
    [    0.372892] pci 0000:00:1c.4:   IO window: 0xc000-0xcfff
    [    0.372900] pci 0000:00:1c.4:   MEM window: 0xfe400000-0xfe6fffff
    [    0.372906] pci 0000:00:1c.4:   PREFETCH window: 0x000000f0000000-0x000000f01fffff
    [    0.372916] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
    [    0.372918] pci 0000:00:1e.0:   IO window: disabled
    [    0.372926] pci 0000:00:1e.0:   MEM window: 0xfe300000-0xfe3fffff
    [    0.372931] pci 0000:00:1e.0:   PREFETCH window: disabled
    [    0.372959]   alloc irq_desc for 16 on node -1
    [    0.372962]   alloc kstat_irqs on node -1
    [    0.372971] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [    0.372978] pci 0000:00:1c.0: setting latency timer to 64
    [    0.372992]   alloc irq_desc for 17 on node -1
    [    0.372994]   alloc kstat_irqs on node -1
    [    0.372998] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [    0.373005] pci 0000:00:1c.1: setting latency timer to 64
    [    0.373018] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [    0.373025] pci 0000:00:1c.4: setting latency timer to 64
    [    0.373035] pci 0000:00:1e.0: setting latency timer to 64
    [    0.373041] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
    [    0.373044] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
    [    0.373047] pci_bus 0000:09: resource 0 io:  [0xd000-0xdfff]
    [    0.373050] pci_bus 0000:09: resource 1 mem: [0xfe800000-0xfe8fffff]
    [    0.373053] pci_bus 0000:09: resource 2 pref mem [0x80000000-0x801fffff]
    [    0.373056] pci_bus 0000:0b: resource 0 io:  [0x2000-0x2fff]
    [    0.373058] pci_bus 0000:0b: resource 1 mem: [0xfe700000-0xfe7fffff]
    [    0.373061] pci_bus 0000:0b: resource 2 pref mem [0x80200000-0x803fffff]
    [    0.373064] pci_bus 0000:0c: resource 0 io:  [0xc000-0xcfff]
    [    0.373067] pci_bus 0000:0c: resource 1 mem: [0xfe400000-0xfe6fffff]
    [    0.373070] pci_bus 0000:0c: resource 2 pref mem [0xf0000000-0xf01fffff]
    [    0.373073] pci_bus 0000:02: resource 1 mem: [0xfe300000-0xfe3fffff]
    [    0.373076] pci_bus 0000:02: resource 3 io:  [0x00-0xffff]
    [    0.373078] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
    [    0.373126] NET: Registered protocol family 2
    [    0.373249] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    [    0.373649] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    [    0.374317] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    [    0.374678] TCP: Hash tables configured (established 131072 bind 65536)
    [    0.374681] TCP reno registered
    [    0.374817] NET: Registered protocol family 1
    [    0.374843] pci 0000:00:02.0: Boot video device
    [    0.375052] Simple Boot Flag at 0x79 set to 0x1
    [    0.375258] cpufreq-nforce2: No nForce2 chipset.
    [    0.375289] Scanning for low memory corruption every 60 seconds
    [    0.375473] audit: initializing netlink socket (disabled)
    [    0.375486] type=2000 audit(1282911195.375:1): initialized
    [    0.386344] highmem bounce pool size: 64 pages
    [    0.386350] HugeTLB registered 4 MB page size, pre-allocated 0 pages
    [    0.388159] VFS: Disk quotas dquot_6.5.2
    [    0.388234] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [    0.396810] fuse init (API version 7.13)
    [    0.396913] msgmni has been set to 1679
    [    0.397176] alg: No test for stdrng (krng)
    [    0.397241] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    [    0.397245] io scheduler noop registered
    [    0.397247] io scheduler anticipatory registered
    [    0.397249] io scheduler deadline registered
    [    0.397297] io scheduler cfq registered (default)
    [    0.397509]   alloc irq_desc for 24 on node -1
    [    0.397512]   alloc kstat_irqs on node -1
    [    0.397526] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
    [    0.397540] pcieport 0000:00:1c.0: setting latency timer to 64
    [    0.397733]   alloc irq_desc for 25 on node -1
    [    0.397735]   alloc kstat_irqs on node -1
    [    0.397746] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
    [    0.397759] pcieport 0000:00:1c.1: setting latency timer to 64
    [    0.397943]   alloc irq_desc for 26 on node -1
    [    0.397945]   alloc kstat_irqs on node -1
    [    0.397955] pcieport 0000:00:1c.4: irq 26 for MSI/MSI-X
    [    0.397968] pcieport 0000:00:1c.4: setting latency timer to 64
    [    0.398095] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [    0.398209] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [    0.398364] ACPI: AC Adapter [AC] (off-line)
    [    0.398452] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
    [    0.399136] ACPI: Lid Switch [LID]
    [    0.399188] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
    [    0.399196] ACPI: Power Button [PBTN]
    [    0.399244] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
    [    0.399247] ACPI: Sleep Button [SBTN]
    [    0.400006] ACPI: SSDT 7f66e4f6 00286 (v01  PmRef  Cpu0Ist 00003000 INTL 20050624)
    [    0.400563] ACPI: SSDT 7f66de8c 005E5 (v01  PmRef  Cpu0Cst 00003001 INTL 20050624)
    [    0.401013] Monitor-Mwait will be used to enter C-1 state
    [    0.401045] Monitor-Mwait will be used to enter C-2 state
    [    0.401069] Monitor-Mwait will be used to enter C-3 state
    [    0.401075] Marking TSC unstable due to TSC halts in idle
    [    0.401154] processor LNXCPU:00: registered as cooling_device0
    [    0.401550] ACPI: SSDT 7f66e77c 000C4 (v01  PmRef  Cpu1Ist 00003000 INTL 20050624)
    [    0.401909] ACPI: SSDT 7f66e471 00085 (v01  PmRef  Cpu1Cst 00003000 INTL 20050624)
    [    0.402227] Switching to clocksource hpet
    [    0.409470] processor LNXCPU:01: registered as cooling_device1
    [    0.411740] thermal LNXTHERM:01: registered as thermal_zone0
    [    0.411750] ACPI: Thermal Zone [THM] (48 C)
    [    0.417042] isapnp: Scanning for PnP cards...
    [    0.485405] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    [    0.487036] brd: module loaded
    [    0.487572] loop: module loaded
    [    0.487693] input: Macintosh mouse button emulation as /devices/virtual/input/input3
    [    0.487828] ata_piix 0000:00:1f.1: version 2.13
    [    0.487846] ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [    0.487899] ata_piix 0000:00:1f.1: setting latency timer to 64
    [    0.493094] scsi0 : ata_piix
    [    0.494548] ACPI: Battery Slot [BAT0] (battery present)
    [    0.494573] scsi1 : ata_piix
    [    0.495229] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x6fa0 irq 14
    [    0.495232] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x6fa8 irq 15
    [    0.495629] Fixed MDIO Bus: probed
    [    0.495667] PPP generic driver version 2.4.2
    [    0.495731] tun: Universal TUN/TAP device driver, 1.6
    [    0.495733] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    [    0.495842] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    0.495871]   alloc irq_desc for 22 on node -1
    [    0.495874]   alloc kstat_irqs on node -1
    [    0.495882] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
    [    0.495905] ehci_hcd 0000:00:1a.7: setting latency timer to 64
    [    0.495909] ehci_hcd 0000:00:1a.7: EHCI Host Controller
    [    0.495950] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
    [    0.495986] ehci_hcd 0000:00:1a.7: debug port 1
    [    0.499886] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
    [    0.500131] ehci_hcd 0000:00:1a.7: irq 22, io mem 0xfed1c400
    [    0.536195] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
    [    0.536342] usb usb1: configuration #1 chosen from 1 choice
    [    0.536376] hub 1-0:1.0: USB hub found
    [    0.536388] hub 1-0:1.0: 4 ports detected
    [    0.536467]   alloc irq_desc for 20 on node -1
    [    0.536470]   alloc kstat_irqs on node -1
    [    0.536477] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    [    0.536502] ehci_hcd 0000:00:1d.7: setting latency timer to 64
    [    0.536506] ehci_hcd 0000:00:1d.7: EHCI Host Controller
    [    0.536548] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
    [    0.536585] ehci_hcd 0000:00:1d.7: debug port 1
    [    0.540476] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
    [    0.540508] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfed1c000
    [    0.548075] ata2: port disabled. ignoring.
    [    0.556045] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [    0.556211] usb usb2: configuration #1 chosen from 1 choice
    [    0.556246] hub 2-0:1.0: USB hub found
    [    0.556258] hub 2-0:1.0: 6 ports detected
    [    0.556342] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    0.556365] uhci_hcd: USB Universal Host Controller Interface driver
    [    0.556421] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    [    0.556433] uhci_hcd 0000:00:1a.0: setting latency timer to 64
    [    0.556438] uhci_hcd 0000:00:1a.0: UHCI Host Controller
    [    0.556484] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
    [    0.556521] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00006f20
    [    0.556623] usb usb3: configuration #1 chosen from 1 choice
    [    0.556651] hub 3-0:1.0: USB hub found
    [    0.556660] hub 3-0:1.0: 2 ports detected
    [    0.556714]   alloc irq_desc for 21 on node -1
    [    0.556716]   alloc kstat_irqs on node -1
    [    0.556724] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    [    0.556732] uhci_hcd 0000:00:1a.1: setting latency timer to 64
    [    0.556736] uhci_hcd 0000:00:1a.1: UHCI Host Controller
    [    0.556779] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
    [    0.556820] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00006f00
    [    0.556921] usb usb4: configuration #1 chosen from 1 choice
    [    0.556949] hub 4-0:1.0: USB hub found
    [    0.556957] hub 4-0:1.0: 2 ports detected
    [    0.557016] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    [    0.557024] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [    0.557028] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [    0.557068] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
    [    0.557097] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00006f80
    [    0.557193] usb usb5: configuration #1 chosen from 1 choice
    [    0.557221] hub 5-0:1.0: USB hub found
    [    0.557228] hub 5-0:1.0: 2 ports detected
    [    0.557283] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    [    0.557290] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [    0.557294] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [    0.557327] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
    [    0.557356] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00006f60
    [    0.557453] usb usb6: configuration #1 chosen from 1 choice
    [    0.557480] hub 6-0:1.0: USB hub found
    [    0.557488] hub 6-0:1.0: 2 ports detected
    [    0.557546] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
    [    0.557553] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [    0.557557] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [    0.557593] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
    [    0.557623] uhci_hcd 0000:00:1d.2: irq 22, io base 0x00006f40
    [    0.557721] usb usb7: configuration #1 chosen from 1 choice
    [    0.557752] hub 7-0:1.0: USB hub found
    [    0.557759] hub 7-0:1.0: 2 ports detected
    [    0.557888] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [    0.573149] i8042.c: Detected active multiplexing controller, rev 1.1.
    [    0.598025] serio: i8042 KBD port at 0x60,0x64 irq 1
    [    0.612354] serio: i8042 AUX0 port at 0x60,0x64 irq 12
    [    0.612409] serio: i8042 AUX1 port at 0x60,0x64 irq 12
    [    0.612439] serio: i8042 AUX2 port at 0x60,0x64 irq 12
    [    0.612463] serio: i8042 AUX3 port at 0x60,0x64 irq 12
    [    0.612617] mice: PS/2 mouse device common for all mice
    [    0.612780] rtc_cmos 00:04: RTC can wake from S4
    [    0.612835] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
    [    0.612876] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
    [    0.613008] device-mapper: uevent: version 1.0.3
    [    0.635447] Freeing initrd memory: 13390k freed
    [    0.645230] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
    [    0.645359] device-mapper: multipath: version 1.1.0 loaded
    [    0.645363] device-mapper: multipath round-robin: version 1.0.0 loaded
    [    0.645513] EISA: Probing bus 0 at eisa.0
    [    0.645524] Cannot allocate resource for EISA slot 1
    [    0.645527] Cannot allocate resource for EISA slot 2
    [    0.645556] EISA: Detected 0 cards.
    [    0.645723] cpuidle: using governor ladder
    [    0.645855] cpuidle: using governor menu
    [    0.646367] TCP cubic registered
    [    0.646540] NET: Registered protocol family 10
    [    0.647075] lo: Disabled Privacy Extensions
    [    0.647460] NET: Registered protocol family 17
    [    0.648097] Using IPI No-Shortcut mode
    [    0.648190] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
    [    0.648943] PM: Resume from disk failed.
    [    0.648958] registered taskstats version 1
    [    0.649660]   Magic number: 6:481:229
    [    0.649763] rtc_cmos 00:04: setting system clock to 2010-08-27 12:13:15 UTC (1282911195)
    [    0.649767] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
    [    0.649768] EDD information not available.
    [    0.723685] ata1.00: ATAPI: TSSTcorp DVD+/-RW TS-L632H, D400, max UDMA/33
    [    0.813988] isapnp: No Plug & Play device found
    [    0.814323] ata1.00: configured for UDMA/33
    [    0.820843] scsi 0:0:0:0: CD-ROM            TSSTcorp DVD+-RW TS-L632H D400 PQ: 0 ANSI: 5
    [    0.836613] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    [    0.836617] Uniform CD-ROM driver Revision: 3.20
    [    0.836733] sr 0:0:0:0: Attached scsi CD-ROM sr0
    [    0.836797] sr 0:0:0:0: Attached scsi generic sg0 type 5
    [    0.836865] Freeing unused kernel memory: 660k freed
    [    0.837315] Write protecting the kernel text: 4680k
    [    0.837375] Write protecting the kernel read-only data: 1844k
    [    0.859946] udev: starting version 151
    [    0.900193] usb 1-1: new high speed USB device using ehci_hcd and address 2
    [    0.988500] sky2 driver version 1.25
    [    0.988561] sky2 0000:09:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [    0.988581] sky2 0000:09:00.0: setting latency timer to 64
    [    0.988622] sky2 0000:09:00.0: Yukon-2 FE+ chip revision 0
    [    0.988745]   alloc irq_desc for 27 on node -1
    [    0.988747]   alloc kstat_irqs on node -1
    [    0.988768] sky2 0000:09:00.0: irq 27 for MSI/MSI-X
    [    0.989592] sky2 eth0: addr 00:21:9b:dd:ca:a4
    [    0.989766] Linux agpgart interface v0.103
    [    1.002481] b43-pci-bridge 0000:0b:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [    1.002500] b43-pci-bridge 0000:0b:00.0: setting latency timer to 64
    [    1.015335] ahci 0000:00:1f.2: version 3.0
    [    1.015360] ahci 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [    1.015423]   alloc irq_desc for 28 on node -1
    [    1.015425]   alloc kstat_irqs on node -1
    [    1.015441] ahci 0000:00:1f.2: irq 28 for MSI/MSI-X
    [    1.015527] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x5 impl SATA mode
    [    1.015531] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems 
    [    1.015538] ahci 0000:00:1f.2: setting latency timer to 64
    [    1.037311] usb 1-1: configuration #1 chosen from 1 choice
    [    1.053115] scsi2 : ahci
    [    1.058466] scsi3 : ahci
    [    1.059600] scsi4 : ahci
    [    1.059905] ata3: SATA max UDMA/133 abar m2048@0xfe9fb800 port 0xfe9fb900 irq 28
    [    1.059908] ata4: DUMMY
    [    1.059912] ata5: SATA max UDMA/133 abar m2048@0xfe9fb800 port 0xfe9fba00 irq 28
    [    1.060068] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
    [    1.060484] agpgart-intel 0000:00:00.0: detected 7676K stolen memory
    [    1.061725] ohci1394 0000:02:09.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [    1.067363] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
    [    1.073176] ssb: Sonics Silicon Backplane found on PCI device 0000:0b:00.0
    [    1.110254] [drm] Initialized drm 1.1.0 20060810
    [    1.119100] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]  MMIO=[fe3ff800-fe3fffff]  Max Packet=[2048]  IR/IT contexts=[4/4]
    [    1.380086] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [    1.380116] ata5: SATA link down (SStatus 0 SControl 300)
    [    1.425526] ata3.00: ATA-8: WDC WD1600BEVT-75ZCT1, 11.01A11, max UDMA/133
    [    1.425530] ata3.00: 312581808 sectors, multi 8: LBA48 NCQ (depth 31/32), AA
    [    1.426985] ata3.00: configured for UDMA/133
    [    1.440202] scsi 2:0:0:0: Direct-Access     ATA      WDC WD1600BEVT-7 11.0 PQ: 0 ANSI: 5
    [    1.440391] sd 2:0:0:0: Attached scsi generic sg1 type 0
    [    1.440428] sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
    [    1.440501] sd 2:0:0:0: [sda] Write Protect is off
    [    1.440504] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [    1.440533] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [    1.440698]  sda: sda1 sda2 < sda5 >
    [    1.477527] sd 2:0:0:0: [sda] Attached SCSI disk
    [    1.504217] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [    1.504224] i915 0000:00:02.0: setting latency timer to 64
    [    1.509050]   alloc irq_desc for 29 on node -1
    [    1.509054]   alloc kstat_irqs on node -1
    [    1.509064] i915 0000:00:02.0: irq 29 for MSI/MSI-X
    [    1.509072] [drm] set up 7M of stolen space
    [    1.991629] [drm] initialized overlay support
    [    2.597452] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[334fc00025e97070]
    [    2.715339] fb0: inteldrmfb frame buffer device
    [    2.715343] registered panic notifier
    [    2.728344] acpi device:2f: registered as cooling_device2
    [    2.728832] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input5
    [    2.728883] ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
    [    2.728946] ACPI Warning for \_SB_.PCI0.VID2._DOD: Return Package has no elements (empty) (20090903/nspredef-433)
    [    2.729039] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:01/input/input6
    [    2.729079] ACPI: Video Device [VID2] (multi-head: yes  rom: no  post: no)
    [    2.729108] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [    2.731166] vga16fb: initializing
    [    2.731171] vga16fb: mapped to 0xc00a0000
    [    2.731175] vga16fb: not registering due to another framebuffer present
    [    2.972404] Console: switching to colour frame buffer device 160x50
    [    3.897884] xor: automatically using best checksumming function: pIII_sse
    [    3.916011]    pIII_sse  :  6831.000 MB/sec
    [    3.916013] xor: using function: pIII_sse (6831.000 MB/sec)
    [    3.920210] device-mapper: dm-raid45: initialized v0.2594b
    [    4.005810] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
    [    4.005816] EXT4-fs (sda1): write access will be enabled during recovery
    [    4.827462] EXT4-fs (sda1): orphan cleanup on readonly fs
    [    4.827475] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4197846
    [    4.827567] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 4197756
    [    4.827605] EXT4-fs (sda1): 2 orphan inodes deleted
    [    4.827609] EXT4-fs (sda1): recovery complete
    [    5.316160] EXT4-fs (sda1): mounted filesystem with ordered data mode
    [    7.300703] Adding 6010872k swap on /dev/sda5.  Priority:-1 extents:1 across:6010872k 
    [    7.521175] udev: starting version 151
    [    8.499132] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
    [    8.632083] input: Dell WMI hotkeys as /devices/virtual/input/input7
    [    8.888235] cfg80211: Calling CRDA to update world regulatory domain
    [    8.925196] lp: driver loaded but no devices found
    [    8.930897] Linux video capture interface: v2.00
    [    8.985872] uvcvideo: Found UVC 1.00 device Laptop Integrated Webcam (05a9:2640)
    [    8.986213] uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
    [    8.986945] input: Laptop Integrated Webcam as /devices/pci0000:00/0000:00:1a.7/usb1/1-1/1-1:1.0/input/input8
    [    8.987062] usbcore: registered new interface driver uvcvideo
    [    8.987108] USB Video Class driver (v0.1.0)
    [    9.350521] input: PS/2 Mouse as /devices/platform/i8042/serio2/input/input9
    [    9.367548] ricoh-mmc: Ricoh MMC Controller disabling driver
    [    9.367552] ricoh-mmc: Copyright(c) Philip Langdale
    [    9.367589] ricoh-mmc: Ricoh MMC controller found at 0000:02:09.2 [1180:0843] (rev 12)
    [    9.367612] ricoh-mmc: Controller is now disabled.
    [    9.369405] sdhci: Secure Digital Host Controller Interface driver
    [    9.369408] sdhci: Copyright(c) Pierre Ossman
    [    9.375737] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio2/input/input10
    [    9.615095] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
    [    9.615516] sdhci-pci 0000:02:09.1: SDHCI controller found [1180:0822] (rev 22)
    [    9.615543]   alloc irq_desc for 18 on node -1
    [    9.615546]   alloc kstat_irqs on node -1
    [    9.615554] sdhci-pci 0000:02:09.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
    [    9.617810] Registered led device: mmc0::
    [    9.619981] mmc0: SDHCI controller on PCI [0000:02:09.1] using DMA
    [    9.700174] Disabling lock debugging due to kernel taint
    [    9.707822] ndiswrapper version 1.55 loaded (smp=yes, preempt=no)
    [   10.664672] cfg80211: World regulatory domain updated:
    [   10.664677] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    [   10.664680] 	(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   10.664683] 	(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [   10.664686] 	(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [   10.664689] 	(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   10.664691] 	(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   10.755450] phy0: Selected rate control algorithm 'minstrel'
    [   10.756348] Registered led device: b43-phy0::tx
    [   10.756369] Registered led device: b43-phy0::rx
    [   10.756388] Registered led device: b43-phy0::radio
    [   10.756481] Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
    [   10.766758] usbcore: registered new interface driver ndiswrapper
    [   12.628388] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
    [   12.628489]   alloc irq_desc for 30 on node -1
    [   12.628493]   alloc kstat_irqs on node -1
    [   12.628510] HDA Intel 0000:00:1b.0: irq 30 for MSI/MSI-X
    [   12.628553] HDA Intel 0000:00:1b.0: setting latency timer to 64
    [   12.958580] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input11
    [   13.180206] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
    [   13.180319] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
    [   13.180397] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
    [   20.029234] b43-pci-bridge 0000:0b:00.0: PCI INT A disabled
    [   20.072156] usbcore: deregistering interface driver ndiswrapper
    [   20.083449] ndiswrapper version 1.55 loaded (smp=yes, preempt=no)
    [   20.096715] usbcore: registered new interface driver ndiswrapper
    [   20.164978] b43-pci-bridge 0000:0b:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [   20.165003] b43-pci-bridge 0000:0b:00.0: setting latency timer to 64
    [   20.232192] ssb: Sonics Silicon Backplane found on PCI device 0000:0b:00.0
    [   20.250529] cfg80211: Calling CRDA to update world regulatory domain
    [   20.259248] cfg80211: World regulatory domain updated:
    [   20.259252] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    [   20.259256] 	(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   20.259258] 	(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [   20.259261] 	(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    [   20.259264] 	(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   20.259267] 	(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    [   20.280696] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
    [   20.348448] phy0: Selected rate control algorithm 'minstrel'
    [   20.349295] Registered led device: b43-phy0::tx
    [   20.349316] Registered led device: b43-phy0::rx
    [   20.349337] Registered led device: b43-phy0::radio
    [   20.349439] Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
    [   20.946588] ppdev: user-space parallel port driver
    [  106.926226] sky2 eth0: enabling interface
    [  106.926737] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [  106.972153] b43 ssb0:0: firmware: requesting b43/ucode15.fw
    [  107.031356] b43 ssb0:0: firmware: requesting b43/lp0initvals15.fw
    [  107.038053] b43 ssb0:0: firmware: requesting b43/lp0bsinitvals15.fw
    [  107.176176] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    [  112.704977] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [  207.629881] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
    [  207.630357] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [  207.902901] sky2 eth0: Link is down.
    [  217.498509] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
    [  217.720108] eth0: no IPv6 routers present
    [  260.712471] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [  260.720172] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [  260.722831] wlan0: direct probe responded
    [  260.722840] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [  260.724530] wlan0: authenticated
    [  260.724573] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [  260.727212] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [  260.727220] wlan0: associated
    [  260.729443] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [  269.125269] sky2 eth0: Link is down.
    [  269.741909] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [  270.888076] wlan0: no IPv6 routers present
    [  271.148625] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [  271.348095] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [  271.548112] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 3)
    [  271.550806] wlan0: direct probe responded
    [  271.550814] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [  271.552459] wlan0: authenticated
    [  271.552504] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [  271.555053] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [  271.555060] wlan0: associated
    [  273.689245] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
    [  280.398438] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [  281.800570] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [  281.804464] wlan0: direct probe responded
    [  281.804475] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [  281.806145] wlan0: authenticated
    [  281.806193] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [  281.808678] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [  281.808685] wlan0: associated
    [  290.733200] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [  292.144548] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [  292.344102] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [  292.347779] wlan0: direct probe responded
    [  292.347786] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [  292.349485] wlan0: authenticated
    [  292.349513] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [  292.352089] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [  292.352093] wlan0: associated
    [  301.075044] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [  302.468871] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [  302.668107] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [  302.671864] wlan0: direct probe responded
    [  302.671870] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [  302.674605] wlan0: authenticated
    [  302.674647] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [  302.677166] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [  302.677173] wlan0: associated
    [  308.732101] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 1853.464111] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    [ 1858.986143] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 1865.456306] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 1865.640264] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1865.643975] wlan0: direct probe responded
    [ 1865.643984] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1865.645800] wlan0: authenticated
    [ 1865.645842] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1865.648295] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1865.648303] wlan0: associated
    [ 1865.650355] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [ 1874.533293] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1875.776059] wlan0: no IPv6 routers present
    [ 1875.936618] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1876.136065] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [ 1876.139823] wlan0: direct probe responded
    [ 1876.139829] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1876.141524] wlan0: authenticated
    [ 1876.141569] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1876.144088] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1876.144096] wlan0: associated
    [ 1885.078737] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1886.473564] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1886.477251] wlan0: direct probe responded
    [ 1886.477257] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1886.478977] wlan0: authenticated
    [ 1886.479003] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1886.481590] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1886.481595] wlan0: associated
    [ 1895.215215] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1896.621948] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1896.625626] wlan0: direct probe responded
    [ 1896.625631] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1896.627331] wlan0: authenticated
    [ 1896.627353] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1896.629937] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1896.629940] wlan0: associated
    [ 1905.557976] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1906.960611] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1906.964303] wlan0: direct probe responded
    [ 1906.964314] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1906.966041] wlan0: authenticated
    [ 1906.966085] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1906.968551] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1906.968560] wlan0: associated
    [ 1915.694188] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1917.096565] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1917.100571] wlan0: direct probe responded
    [ 1917.100581] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1917.102244] wlan0: authenticated
    [ 1917.102290] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1917.104866] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1917.104875] wlan0: associated
    [ 1919.249060] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 1923.632278] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 1923.816237] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1923.824258] wlan0: direct probe responded
    [ 1923.824268] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1923.825879] wlan0: authenticated
    [ 1923.825925] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1923.828443] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1923.828451] wlan0: associated
    [ 1932.588345] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1933.992628] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1934.192087] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [ 1934.195823] wlan0: direct probe responded
    [ 1934.195829] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1934.197549] wlan0: authenticated
    [ 1934.197594] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1934.200084] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1934.200092] wlan0: associated
    [ 1942.827760] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1944.228579] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1944.232309] wlan0: direct probe responded
    [ 1944.232320] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1944.234068] wlan0: authenticated
    [ 1944.234116] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1944.237089] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1944.237099] wlan0: associated
    [ 1952.964221] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1954.364594] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1954.368302] wlan0: direct probe responded
    [ 1954.368313] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1954.370008] wlan0: authenticated
    [ 1954.370052] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1954.372565] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1954.372572] wlan0: associated
    [ 1963.211193] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1964.612590] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1964.616651] wlan0: direct probe responded
    [ 1964.616662] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1964.618316] wlan0: authenticated
    [ 1964.618361] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1964.620942] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1964.620949] wlan0: associated
    [ 1973.546307] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1974.948622] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1975.148069] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [ 1975.348070] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 3)
    [ 1975.351773] wlan0: direct probe responded
    [ 1975.351783] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1975.353528] wlan0: authenticated
    [ 1975.353573] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1975.356188] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1975.356198] wlan0: associated
    [ 1982.249063] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 1986.997215] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 1987.180262] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1987.380113] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [ 1987.383864] wlan0: direct probe responded
    [ 1987.383873] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1987.385531] wlan0: authenticated
    [ 1987.385578] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1987.388249] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1987.388258] wlan0: associated
    [ 1996.284806] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 1997.684571] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 1997.688288] wlan0: direct probe responded
    [ 1997.688300] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 1997.689977] wlan0: authenticated
    [ 1997.690029] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 1997.692520] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 1997.692530] wlan0: associated
    [ 2006.515523] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2007.916661] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2007.920380] wlan0: direct probe responded
    [ 2007.920390] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2007.922175] wlan0: authenticated
    [ 2007.922221] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2007.924774] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2007.924781] wlan0: associated
    [ 2009.797077] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 2029.756301] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 2029.940263] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2029.943979] wlan0: direct probe responded
    [ 2029.943989] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2029.945658] wlan0: authenticated
    [ 2029.945700] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2029.948201] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2029.948207] wlan0: associated
    [ 2038.871733] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2040.272617] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2040.472128] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [ 2040.475884] wlan0: direct probe responded
    [ 2040.475892] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2040.477591] wlan0: authenticated
    [ 2040.477637] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2040.480115] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2040.480124] wlan0: associated
    [ 2049.315255] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2050.720513] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2050.920094] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [ 2050.923861] wlan0: direct probe responded
    [ 2050.923868] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2050.925577] wlan0: authenticated
    [ 2050.925622] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2050.928126] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2050.928134] wlan0: associated
    [ 2059.658067] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2061.068585] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2061.072422] wlan0: direct probe responded
    [ 2061.072432] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2061.074063] wlan0: authenticated
    [ 2061.074114] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2061.076909] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2061.076918] wlan0: associated
    [ 2064.525060] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 2071.672352] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 2071.856288] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2071.859999] wlan0: direct probe responded
    [ 2071.860047] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2071.861804] wlan0: authenticated
    [ 2071.861845] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2071.864382] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2071.864391] wlan0: associated
    [ 2075.761075] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 2079.629288] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 2079.812256] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2079.815963] wlan0: direct probe responded
    [ 2079.815973] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2079.817640] wlan0: authenticated
    [ 2079.817689] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2079.820197] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2079.820206] wlan0: associated
    [ 2088.531292] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2089.926089] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2089.930146] wlan0: direct probe responded
    [ 2089.930156] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2089.931763] wlan0: authenticated
    [ 2089.931812] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2089.934341] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2089.934350] wlan0: associated
    [ 2092.336063] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 2092.521178] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 2092.704265] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2092.904134] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [ 2093.105145] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 3)
    [ 2093.304105] wlan0: direct probe to AP 00:26:44:05:c0:1d timed out
    [ 2104.009153] b43-phy0: Radio hardware status changed to DISABLED
    [ 2109.008161] b43-phy0: Radio hardware status changed to ENABLED
    [ 2109.332138] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    [ 2114.857024] ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 2115.040739] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2115.240125] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [ 2115.440077] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 3)
    [ 2115.640105] wlan0: direct probe to AP 00:26:44:05:c0:1d timed out
    [ 2140.349086] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    [ 2140.360196] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2140.364674] wlan0: direct probe responded
    [ 2140.364682] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2140.366364] wlan0: authenticated
    [ 2140.366406] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2140.368903] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2140.368911] wlan0: associated
    [ 2140.370989] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
    [ 2149.050097] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2150.464571] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2150.469160] wlan0: direct probe responded
    [ 2150.469171] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2150.470791] wlan0: authenticated
    [ 2150.470836] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2150.473630] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2150.473639] wlan0: associated
    [ 2150.872094] wlan0: no IPv6 routers present
    [ 2159.284613] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2160.692859] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2160.892115] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 2)
    [ 2160.895872] wlan0: direct probe responded
    [ 2160.895881] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2160.897558] wlan0: authenticated
    [ 2160.897602] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2160.900141] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2160.900149] wlan0: associated
    [ 2169.524000] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2170.925137] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2170.928864] wlan0: direct probe responded
    [ 2170.928874] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2170.930554] wlan0: authenticated
    [ 2170.930601] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2170.933171] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2170.933179] wlan0: associated
    [ 2179.870312] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2181.280533] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2181.284579] wlan0: direct probe responded
    [ 2181.284591] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2181.286203] wlan0: authenticated
    [ 2181.286251] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2181.288750] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2181.288761] wlan0: associated
    [ 2190.011998] wlan0: deauthenticated from 00:26:44:05:c0:1d (Reason: 15)
    [ 2191.420623] wlan0: direct probe to AP 00:26:44:05:c0:1d (try 1)
    [ 2191.424306] wlan0: direct probe responded
    [ 2191.424312] wlan0: authenticate with AP 00:26:44:05:c0:1d (try 1)
    [ 2191.425992] wlan0: authenticated
    [ 2191.426013] wlan0: associate with AP 00:26:44:05:c0:1d (try 1)
    [ 2191.428605] wlan0: RX AssocResp from 00:26:44:05:c0:1d (capab=0x411 status=0 aid=1)
    [ 2191.428608] wlan0: associated
    [ 2199.253069] wlan0: deauthenticating from 00:26:44:05:c0:1d by local choice (reason=3)
    Code:
    [  106.972153] b43 ssb0:0: firmware: requesting b43/ucode15.fw
    [  107.031356] b43 ssb0:0: firmware: requesting b43/lp0initvals15.fw
    [  107.038053] b43 ssb0:0: firmware: requesting b43/lp0bsinitvals15.fw
    [  107.176176] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    [ 1853.464111] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    [ 2109.332138] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    Code:
    2.6.32-24-generic

  2. #2
    Just Joined!
    Join Date
    Aug 2010
    Posts
    10

    other version of information

    Code:
    ============ lspci ============
    00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub [8086:2a00] (rev 0c)
    	Kernel driver in use: agpgart-intel
    	Kernel modules: intel-agp
    00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a02] (rev 0c)
    	Kernel driver in use: i915
    	Kernel modules: i915
    00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a03] (rev 0c)
    00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02)
    	Kernel driver in use: ehci_hcd
    00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02)
    	Kernel driver in use: HDA Intel
    	Kernel modules: snd-hda-intel
    00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02)
    	Kernel driver in use: pcieport
    	Kernel modules: shpchp
    00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 02)
    	Kernel driver in use: pcieport
    	Kernel modules: shpchp
    00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 [8086:2847] (rev 02)
    	Kernel driver in use: pcieport
    	Kernel modules: shpchp
    00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 02)
    	Kernel driver in use: uhci_hcd
    00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02)
    	Kernel driver in use: ehci_hcd
    00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f2)
    00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller [8086:2815] (rev 02)
    	Kernel modules: iTCO_wdt
    00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller [8086:2850] (rev 02)
    	Kernel driver in use: ata_piix
    00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller [8086:2829] (rev 02)
    	Kernel driver in use: ahci
    	Kernel modules: ahci
    00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 02)
    	Kernel modules: i2c-i801
    02:09.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (rev 05)
    	Kernel driver in use: ohci1394
    	Kernel modules: firewire-ohci, ohci1394
    02:09.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 22)
    	Kernel driver in use: sdhci-pci
    	Kernel modules: sdhci-pci
    02:09.2 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller [1180:0843] (rev 12)
    	Kernel driver in use: ricoh-mmc
    	Kernel modules: ricoh_mmc
    02:09.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 12)
    02:09.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev ff)
    09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] (rev 12)
    	Kernel driver in use: sky2
    	Kernel modules: sky2
    0b:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01)
    	Kernel driver in use: b43-pci-bridge
    	Kernel modules: ssb
    
    ============ lsusb ============
    Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 001 Device 002: ID 05a9:2640 OmniVision Technologies, Inc. OV2640 Webcam
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    
    ============ lsmod ============
    Module                  Size  Used by
    binfmt_misc             6587  1 
    ppdev                   5259  0 
    b43                   163523  0 
    mac80211              205146  1 b43
    b44                    25574  0 
    cfg80211              126517  2 b43,mac80211
    ssb                    38671  2 b43,b44
    mii                     4381  1 b44
    ndiswrapper           184677  0 
    dm_crypt               11331  0 
    snd_hda_codec_idt      53916  1 
    snd_hda_codec_intelhdmi     9559  1 
    snd_hda_intel          20799  2 
    snd_hda_codec          87096  3 snd_hda_codec_idt,snd_hda_codec_intelhdmi,snd_hda_intel
    snd_hwdep               5668  1 snd_hda_codec
    snd_pcm_oss            34603  0 
    snd_mixer_oss          13929  1 snd_pcm_oss
    snd_pcm                71678  3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
    snd_seq_dummy           1498  0 
    snd_seq_oss            27626  0 
    arc4                    1153  2 
    snd_seq_midi            4621  0 
    snd_rawmidi            19141  1 snd_seq_midi
    snd_seq_midi_event      6003  2 snd_seq_oss,snd_seq_midi
    snd_seq                48042  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
    snd_timer              18710  2 snd_pcm,snd_seq
    snd_seq_device          6052  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
    snd                    56687  19 snd_hda_codec_idt,snd_hda_codec_intelhdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
    joydev                  8708  0 
    soundcore               6620  1 snd
    sdhci_pci               5470  0 
    sdhci                  15462  1 sdhci_pci
    ricoh_mmc               2923  0 
    snd_page_alloc          7140  2 snd_hda_intel,snd_pcm
    uvcvideo               56990  0 
    videodev               34361  1 uvcvideo
    psmouse                63245  0 
    v4l1_compat            13251  2 uvcvideo,videodev
    dell_wmi                1793  0 
    led_class               2864  2 b43,sdhci
    serio_raw               3978  0 
    lp                      7028  0 
    dell_laptop             6856  0 
    parport                32635  2 ppdev,lp
    dcdbas                  5422  1 dell_laptop
    dm_raid45              81647  0 
    xor                    15028  1 dm_raid45
    fbcon                  35102  71 
    tileblit                2031  1 fbcon
    font                    7557  1 fbcon
    bitblit                 4707  1 fbcon
    softcursor              1189  1 bitblit
    vga16fb                11385  0 
    vgastate                8961  1 vga16fb
    i915                  285076  3 
    drm_kms_helper         29297  1 i915
    drm                   162409  4 i915,drm_kms_helper
    ohci1394               26950  0 
    ieee1394               81181  1 ohci1394
    intel_agp              24119  2 i915
    i2c_algo_bit            5028  1 i915
    ahci                   32200  2 
    sky2                   40775  0 
    agpgart                31724  2 drm,intel_agp
    video                  17375  1 i915
    output                  1871  1 video
    
    ============ dmesg-firmware ============
    [  106.972153] b43 ssb0:0: firmware: requesting b43/ucode15.fw
    [  107.031356] b43 ssb0:0: firmware: requesting b43/lp0initvals15.fw
    [  107.038053] b43 ssb0:0: firmware: requesting b43/lp0bsinitvals15.fw
    [  107.176176] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    [ 1853.464111] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    [ 2109.332138] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
    
    ============ kernel version ============
    2.6.32-24-generic
    
    ============ ifconfig ============
    eth0      Link encap:Ethernet  HWaddr 00:21:9b:dd:ca:a4  
              inet addr:192.168.1.65  Bcast:192.168.1.255  Mask:255.255.255.0
              inet6 addr: fe80::221:9bff:fedd:caa4/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:16143 errors:0 dropped:0 overruns:0 frame:0
              TX packets:17161 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:10280810 (10.2 MB)  TX bytes:4197730 (4.1 MB)
              Interrupt:16 
    
    lo        Link encap:Local Loopback  
              inet addr:127.0.0.1  Mask:255.0.0.0
              inet6 addr: ::1/128 Scope:Host
              UP LOOPBACK RUNNING  MTU:16436  Metric:1
              RX packets:11233 errors:0 dropped:0 overruns:0 frame:0
              TX packets:11233 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:0 
              RX bytes:2117687 (2.1 MB)  TX bytes:2117687 (2.1 MB)
    
    wlan0     Link encap:Ethernet  HWaddr 00:22:5f:04:82:94  
              inet6 addr: fe80::222:5fff:fe04:8294/64 Scope:Link
              UP BROADCAST MULTICAST  MTU:1500  Metric:1
              RX packets:236 errors:0 dropped:0 overruns:0 frame:0
              TX packets:251 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:31860 (31.8 KB)  TX bytes:38074 (38.0 KB)
    
    
    ============ iwconfig ============
    wlan0     IEEE 802.11bg  ESSID:"\xAC\x86!+\xAA\x1AU\xA2\xBEp\xB5s;\x04\\xD36\x94\xB3\xAF\xE2\xF0\xE4\x9EO2\x15I\xFD\x82N\xA9"  
              Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated   
              Tx-Power=20 dBm   
              Retry  long limit:7   RTS thr:off   Fragment thr:off
              Power Management:off

  3. #3
    Linux Guru reed9's Avatar
    Join Date
    Feb 2009
    Location
    Boston, MA
    Posts
    4,651
    You have two different drivers loading, b43 and ndiswrapper, which will conflict. Also, while I think b43 is beginning to support this card, the wl driver should work better.

    If you can get a wired connection do
    Code:
    sudo apt-get install bcmwl-kernel-source bcmwl-modaliases
    Open the file /etc/modprobe.d/blacklist.conf with the text editor of your choice, ie
    Code:
    gksudo gedit /etc/modprobe.d/blacklist.conf
    Add the following two lines
    Code:
    blacklist b43
    blacklist ndiswrapper
    Make sure there isn't a line reading
    Code:
    blacklist wl
    Reboot and it should work. If not, check the output of
    Code:
    lsmod | grep wl
    If there is no output, the module isn't loading. Load as so
    Code:
    sudo modprobe wl
    Make it load at boot
    Code:
    echo "wl" | sudo tee -a /etc/modules

  4. #4
    Just Joined!
    Join Date
    Aug 2010
    Posts
    10
    # This file lists those modules which we don't want to be loaded by
    # alias expansion, usually so some other driver will be loaded for the
    # device instead.

    # evbug is a debug tool that should be loaded explicitly
    blacklist evbug

    # these drivers are very simple, the HID drivers are usually preferred
    blacklist usbmouse
    blacklist usbkbd

    # replaced by e100
    blacklist eepro100

    # replaced by tulip
    blacklist de4x5

    # causes no end of confusion by creating unexpected network interfaces
    blacklist eth1394

    # snd_intel8x0m can interfere with snd_intel8x0, doesn't seem to support much
    # hardware on its own (Ubuntu bug #2011, #6810)
    blacklist snd_intel8x0m

    # Conflicts with dvb driver (which is better for handling this device)
    blacklist snd_aw2

    # causes failure to suspend on HP compaq nc6000 (Ubuntu: #10306)
    blacklist i2c_i801

    # replaced by p54pci
    blacklist prism54

    # replaced by b43 and ssb.
    blacklist bcm43xx

    # most apps now use garmin usb driver directly (Ubuntu: #114565)
    blacklist garmin_gps

    # replaced by asus-laptop (Ubuntu: #184721)
    blacklist asus_acpi

    # low-quality, just noise when being used for sound playback, causes
    # hangs at desktop session start (Ubuntu: #246969)
    blacklist snd_pcsp

    # ugly and loud noise, getting on everyone's nerves; this should be done by a
    # nice pulseaudio bing (Ubuntu: #77010)
    blacklist pcspkr

    # EDAC driver for amd76x clashes with the agp driver preventing the aperture
    # from being initialised (Ubuntu: #297750). Blacklist so that the driver
    # continues to build and is installable for the few cases where its
    # really needed.
    blacklist amd76x_edac
    blacklist b43
    blacklist ndiswrapper
    Code:
    sudo modprobe wl
    Code:
    WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
    WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.
    FATAL: Module wl not found.

    Code:
    echo "wl" | sudo tee -a /etc/modules
    AND IT RESPONDS
    Code:
    wl

    wifi still won't connect; even more it doesn't show me anymore available wifi networks(only wired connections)
    maybe i rebooted wrong
    Code:
    sudo reboot

  5. #5
    Just Joined! Wifi-Fanatux's Avatar
    Join Date
    Mar 2009
    Location
    Northwest
    Posts
    20

    Broadcom 4312

    Depending on the distro (and version) you are using, the Broadcom 4312 wireless chipsets are frequently incompatible with the b43 kernel module and the ssb module on which b43 depends. The Broadcom wireless chipset for the 4312 under these circumstances conflicts with the ssb module.

    This may work for you:
    First, pass this parameter when booting (or add it to the menu.lst): ssb.blacklist=1
    Second, you'll need to install and enable the proprietary Broadcom STA driver.
    Third, you will need to be certain that both the b43 and ssb drivers are blacklisted. Add:
    ssb
    b43
    to the end of /etc/modprobe.d/blacklist.conf

    When you reboot, the installed driver scripts should configure the system to load the wl driver automatically at boot. You can check this with the command:
    lsmod | grep wl
    which should return a line for wl.
    You can also determine which interface your wireless is assigned to with the command:
    ifconfig -a

  6. #6
    Just Joined!
    Join Date
    Aug 2010
    Posts
    10
    I think i am quite new to Linux and that's why, how to understand 'pass this parameter when booting'?
    And when i tried to activate Broadcom STA from hardware drivers, it said that something went wrong or some failure and check var/log/jockey.log

    how do i have to add those blacklist b43 etc. pharses?

    I would like to get this work, but again, i'm too green to mess with those important files and rewriting/ reposting something to the system files.

    Can reloading linux-mint from live dvd make it better?
    Or maybe some other linux.versions would be better? I need fast, simple but also stylish,designed OS?

  7. #7
    Linux Guru rokytnji's Avatar
    Join Date
    Jul 2008
    Location
    Desert
    Posts
    4,002
    pass this parameter when booting
    means type

    ssb.blacklist=1
    at the bottom of boot screen when grub screen shows which kernel of operating system to boot.
    Linux Registered User # 475019
    Lead,Follow, or get the heck out of the way. I Have a Masters in Raising Hell
    Tech Books
    Free Linux Books
    Newbie Guide
    Courses at Home

  8. #8
    Just Joined!
    Join Date
    Aug 2010
    Posts
    10
    sorry
    no such place to type
    i only have linux mint OS

    when i try boot menu, then won't see also any place

    recommend some other linux?

  9. #9
    Just Joined! Wifi-Fanatux's Avatar
    Join Date
    Mar 2009
    Location
    Northwest
    Posts
    20

    Mint is a great distro to start with

    No, don't change distros. Mint should be easy to configure.
    When your Grub screen appears, you should be able to press the "e" key to edit.
    Then there should be a line of instructions for the computer to read in order to boot the computer.
    You should be able to type "ssb.blacklist=1" on that line of instructions, and then I believe you enter "b" to boot (whatever the screen states to boot that edited line.

    To download the STA driver. you will need an internet connection, so you will have to connect a cable up. Then open the synaptic package manager and search for the Broadcom STA driver. Synaptic will install and configure the driver modules for you. But now that I think about it, doesn't Mint have an install proprietary drivers applet? If so select the STA driver (while connected to the internet) and install it.

    The reason for the error in activating is most likely that the wireless card can not be detected because the ssb or b43 module has already connected to the device, therefore not allowing the device to be opened by another application.

    So, you need to blacklist those modules in order to keep the connection to the wireless device open for the STA driver to connect to. You do this by stopping the initialization scripts from loading those drivers in the modprobe.d directory which is accessed during the boot process. To do this:
    Open up a terminal window (Gnome Terminal, XTerminal, or whatever is available in your menu). Type "su" you will be asked for the root password. Then type the file manager you use (Nautilus if Gnome, Konqueror or Dolphin if KDE, Thunar if XFCE - not sure which Mint you are using). You will then be superuser browsing your folders (BE VERY CAREFUL NOT TO DELETE STUFF!).
    Go to the "File System" directory. Open the "etc" folder. Open the "modprobe.d" folder. There will be a file named "blacklist.conf", right click and open with a text editor. Scroll to the bottom and type in:
    ssb
    b43
    (Some distros require "blacklist ssb" and "blacklist b43" you will see other entries in that file, just make your entries similar. Then save the file and close your file manager and terminal that you have open as superuser, to avoid doing something accidentally.

    Then reboot, cross your fingers, and if it works you'll owe me a pint of Guinness stout.

  10. #10
    Just Joined! Wifi-Fanatux's Avatar
    Join Date
    Mar 2009
    Location
    Northwest
    Posts
    20

    BTW its not the Distro

    I thought I'd add that the problem is not the distro you are using. It is the wireless card. For years Broadcom has refused to release the coding for their wireless cards to changing the source code because of copyright protection. That is why it is called "proprietary" software. They also had not made any attempts to create a linux compatible driver. The linux kernel developers have created modules over the years so that broadcom devices can be autodetected by the operating system and that is the b43 module. It doesn't work for all cards. So there is a firmware application called fwcutter to download the broadcom firmware and automatically configure the driver for linux. This works for just about all broadcom cards except the 4312. Why I don't know.

    I've used broadcom cards for years and in the past had to use ndiswrapper to configure the windows driver, because I didn't know about the broadcom devices like you now know. I do know in the future, I will try to buy laptops that use other wireless cards (or pay extra to the manufacturer for a different card) than broadcom, or if I do buy one with a broadcom card, I will research which cards work with the b43 module. It's a pain, but in the end, I've learned a lot about how the operating system works, and I believe that I can do more with linux because of that knowledge.

Page 1 of 2 1 2 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •